Miele H 5461 Bp Manual

							Descaling
Only use the descaling tablets
supplied with the appliance. These
have been specially formulated and
are available to re-order from the
Miele Spare Parts Department or via
the internet on www.miele-shop.com.
Other types of descaling agents will
damage the oven.
Follow the instructions on the
package carefully to avoid damaging
the oven.
Clean the oven interior after
descaling to ensure that all traces of
descaling agent have been removed.When to run the descaling
programme
The descaling programme can be run
at any time.
However, to ensure the oven functions
correctly you will be automatically
prompted to run the descaling
programme after a certain number of
oven uses.
Descaling process (overview)
The descaling process takes approx.
90 minutes and includes a number of
stages:
Preparing the descaling solution
Drawing in the descaling solution
Activation phase
Rinse 1
Rinse 2
Rinse 3
Evaporating the residual moisture
Cleaning and care
61 
						

							Preparation
Dissolve one descaling tablet in
approx. 600 ml of cold tap water.
Place the universal tray on the top
shelf level to collect the descaling
solution after it has been used.
A plastic tube (with clip) is supplied
with your oven so that you do not
have to hold the container with the
descaling agent underneath the
water intake tube.

Attach the plastic tube to the end of
the water intake tube. Place the other
end in the bottom of the descaling
solution container and secure it to the
container with the clip.

Close the door.Start the descaling process.
Select Moisture plusand then
Descale.
Press the OK sensor to start the
suction process.
The segment display shows how the
descaling process is progressing. You
can hear the pump during the
descaling process.
The amount of solution specified can
be more than the amount which is
actually taken in which means that
some of the solution will be left in the
container at the end of descaling. Top
the container up with approx. 300 ml of
water to the container, as the system
will need to draw in some more liquid
during the activation phase.
Once the descaling solution has been
drawn into the appliance
– Activation phase will appear in the
display.
The activation phase takes
approx. 60 minutes.
–
the time left for the activation phase
will be shown counting down in the
display.
The system will take in more liquid at
approximately five minute intervals. You
will hear the noise of the pump for a
moment or so.
The oven lighting and the cooling fan
will remain on during descaling.
Cleaning and care
62 
						

							The steam injection system will need to
be cleanedat the end of the
descaling processto remove all traces
of descaling solution.
Prompts to do this will appear in the
display.
Cleaning is carried out by flushing
approx. 1 litre of mains tap water
through the system. The water is
collected in the universal tray. This
process is repeated three times.
Take the universal tray out of the
oven and empty it. Place the tray
back in the oven again at the top
shelf level.
Unclip the plastic tube from the
container. Rinse the container and fill
with approx. one litre of tap water.
Place the container in the oven, insert
the plastic tube and secure it to the
container with the clip.
Start the first rinse.

Repeat twice.
Empty the universal tray before the
second and third rinse.After the third rinse, residual water will
need to be evaporated from the steam
injection system.
Before proceeding, remove the
plastic tube and the container from
the oven.
The oven will heat up to Evaporate
residual moisture. The time counts
down in the display.
Allow the oven to cool down before
cleaning by hand. Danger of
burning.
Remove the universal tray and empty
it. Clean the oven interior to remove
any condensation and descaling
agent residue.
Leave the oven door open until the
oven interior is completely dry.
Cleaning and care
63 
						

							With the aid of the following guide, minor problems can be easily corrected
without contacting Miele.
If you cannot resolve a problem following these instructions please contact the
Miele Service Department.
Do not attempt to open the appliance casing yourself!
Installation, maintenance and repairs may only be carried out by a suitably
qualified and competent person in strict accordance with current national and
local safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held liable for unauthorised work.
Problem Possible cause and remedy
The display is dark. – Check whether the time of day display is set so that it
does not show in the display (see Settings - Time of day
- Display).
– Check whether the mains fuse has tripped. If it has not
tripped, contact a qualified electrician or the Miele Ser-
vice Department.
The oven does not
heat up.– Check whether the system lockhas been activated
(see Settings - Safety).
– Check whether demo mode has been activated (see
Settings - Showroom prog.).
–
Check whether the mains fuse has tripped. If it has not
tripped, contact a qualified electrician or the Miele Ser-
vice Department.
A noise can be
heard after a
cooking
programme.The cooling fan remains switched on after the end of a
cooking programme (see Settings - Cooling fan).
The door cannot be
opened at the end
of a pyrolytic
cleaning
programme.Switch the appliance off. If the door lock will still not open
please contact the Miele Service Department.
Problem solving guide
64 
						

							Problem Possible cause and remedy
The top lighting is
not working.Disconnect the appliance from the electricity supply:
Switch off and unplug at the socket, or disconnect the
fuse, or switch off at the isolator as appropriate.
Turn the lamp cover a quarter turn anti-clockwise to
release it and then pull it downwards to take it out.
Replace it with a new halogen lamp (Osram 66725 AM/A,
230 V, 25 W, G9).
Refit the lamp cover and turn it clockwise to secure it.
Reconnect the appliance to the mains electricity supply.
The side lighting is
not working.Disconnect the appliance from the electricity supply:
Switch off and unplug at the socket, or disconnect the
fuse, or switch off at the isolator as appropriate.
Remove the shelf runners.
Use the lever supplied to release the lamp cover from its
frame.
Replace it with a new halogen lamp (Osram 66725 AM/A,
230 V, 25 W, G9).
Push the lamp cover back into its retainers, and replace
the shelf runners.

Reconnect the appliance to the mains electricity supply.
Cakes and biscuits
are not cooked
properly after
following the times
given in the chart.–
Check that the correct temperature has been set.
–
Check whether there has been a change to the recipe.
The addition of more liquid or more eggs makes a
moister mix which would need longer to cook.
Cakes / biscuits are
browning unevenly.There will always be a slight unevenness. If browning is
very uneven check that the correct temperature was set
and that the correct shelf level was used.
With conventional heatthe material and colour of the tin
used plays an important role. Light coloured, shiny tins are
less suitable.
Problem solving guide
65 
						

							Problem Possible cause and remedy
Max. operating
duration reached
appears in the
display.Safety switch-off has activated.
The appliance will be ready for use again after it has been
switched off and then back on again.
A fault code
appears in the
display:F+a
numberYou can rectify the faults with the following codes yourself:
–Fault 23: The temperature required for pyrolytic cleaning
was not reached.
This could have been caused by too much soiling in the
oven to start with.
Remove all coarse soiling before starting the pyrolytic
cleaning programme again.
If the fault message appears again please contact the
Miele Service Department.
– Fault 32: The door has not locked for the pyrolytic
cleaning process.
Switch the oven off and start the pyrolytic cleaning
process again.
If the fault code appears again call the Miele Service
Department.
– Fault 33: The door lock for the pyrolytic cleaning process
will not open.
Interrupt the pyrolytic cleaning programme by switching
the oven off. If the door will still not open please contact
the Miele Service Department.
–
Fault 54: The food probe is faulty.
The message will go out as soon as the food probe is
removed from the oven. A replacement can be ordered
from your Miele Dealer or the Miele Spare Parts
Department.
For all other fault codes please contact the Miele Service
Department.
Problem solving guide
66 
						

							After sales service
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact
–your Miele Dealer
or
–Miele (see back cover for contact
details).
A call-out charge will be applied for
service visits where the problem
could have been resolved as
described in these instructions.
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance.
This information is given on the data
plate, visible on the front frame of the
oven, with the door fully open.
Please note that telephone calls may
be monitored and recorded for
training purposes.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the UK, your appliance is guaranteed
for 2 years from the date of purchase.
However, you must activate your cover
by calling 0845 365 6640 or registering
online at www.miele.co.uk.
After Sales / Guarantee
67 
						

							A range of additional accessories as well as cleaning and care products are
available for your Miele oven. Depending on product they are available to order
from your Miele Dealer, the Miele Spare Parts Department or via the internet on
www.miele-shop.com.
FlexiClip telescopic runners
FlexiClip runners can be installed in the
oven. They can be fitted to any shelf
level, and can be fully extended out of
the oven to give a good overview of
cooking in progress.
Baking tray, universal tray and rack
These items, supplied with your oven,
are also available to order.
When ordering, please quote the model
number of your appliance.Pizza stone
The pizza stone is ideal for items which
need a well baked base such as pizza,
quiche, bread, bread rolls and savoury
snacks.
The pizza stone is made from heat
retaining fire brick and is glazed.
Place it directly on the rack.
A paddle made of untreated wood is
supplied with it for placing food on the
pizza stone and taking it off.
Flan/Pizza dish
This circular pan is suitable for cooking
pizzas, flat cakes made with yeast or
whisked mixtures, sweet and savoury
tarts, baked desserts, and can also be
used for frozen cakes and pizzas.
The surface has been treated with
PerfectClean enamel.
Optional accessories
68 
						

							Gourmet oven dish
The gourmet oven dish can be placed
in the oven directly on the runners. It
has non-tip safety notches like the
universal tray to prevent it being pulled
out too far.
It has an anti-stick coating.
It is available in two sizes:
–HUB 5000-M (internal dimensions:
(Capacity approx. 5 litres,
dimensions approx. 38 x 22x8cm)
– HUB 5000-XL (internal dimensions:
(Capacity approx. 8 litres,
dimensions approx. 38 x 35x8cm)Gourmet oven dish lid
A lid is available separately for each of
the gourmet oven dishes.
When ordering a lid, please specify the
gourmet oven dish it is to be used with
(HUB 5000 M or XL).
Miele E-cloth
Removes grease and stains and leaves
no smearing. Suitable for cleaning
surfaces such as stainless steel, glass,
plastic and chrome without the use of
chemicals.
Oven cleaner
Suitable for removing stubborn soiling.
It is not necessary to pre-heat the oven
beforehand.
Optional accessories
69 
						

							All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations (BS
7671 in the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
unauthorised work.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Thevoltage and connected loadare
given on the data plate, visible below
the oven interior, with the door open.
Ensure that these match the household
mains supply. Please quote these data,
and the model and serial number when
contacting Miele.
Connection of this appliance should be
made via a fused connection unit or a
suitable isolator, which complies with
national and local safety regulations,
and the on/off switch should be easily
accessible after the appliance has
been built in.
If the switch is not accessible after
installation (depending on country) an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a residual current
device (RCD). Please contact a
qualified electrician for advice.
When switched off there must be an
all-pole contact gap of 3 mm in theisolator switch (including switch, fuses
and relays acc. to EN 60 335).
Important U.K.
The appliance is supplied for
connection to a 230-240 V, 50 Hz
supply with a 3-core cable.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue = neutral
Brown = live
WARNING
THIS APPLIANCE MUST BE
EARTHED
When replacing the cable supplied
with another cable or changing the
connection, only cable type
H 05 VV-F or H 05 RR-F with a
suitable cross-sectional area (CSA)
may be used (available from the
Miele Customer Contact Centre).
Electrical connection
70