Miele K 1801 Vi Operating And Installation Instructions

Correct use
Do not operate any electrical
equipment (e.g. an electric ice-cream
maker) inside the appliance. Danger of
sparks and explosion.
Do not store explosive materials in
the appliance or any products
containing propellants (e.g. spray
cans). Thermostats switching on may
produce sparks which could present a
fire hazard. Flammable compounds
could explode.
Observe the use-by dates given on
food to avoid the risk of food poisoning.
Storage times will depend on several
factors, including the...

Disposal of your old appliance
Before disposing of an old
appliance, first make the door latches
or locks unusable.
This way you will prevent children from
accidentally locking themselves in and
endangering their lives.
Be careful not to damage any part of
the pipework whilst awaiting disposal,
e.g. by
–puncturing the refrigerant channels
in the evaporator.
–bending any pipework.
– scratching the surface coating.
Splashes of refrigerant can damage the
eyes.
The manufacturer cannot be held
liable for...

Normal energy
consumptionIncreased energy
consumption
Installation siteIn a ventilated room. In an enclosed, unventilated room.
Protected from direct sunlight. In direct sunlight.
Not near to a heat source (radiator,
oven).Near to a heat source (radiator,
oven).
Where the ideal ambient room
temperature is approx. 20°C.Where there is a high ambient room
temperature.
Do not cover the ventilation gaps
and dust them regularly.
Temperature setting
with a thermostat
which is approximate
(set in stages).With a...

Before using for the first time
Clean the inside of the appliance and
the accessories with lukewarm water
and a little washing up liquid, and
then dry with a soft cloth.
Important:
To ensure the correct functioning of
the appliance, let it stand for approx.
1 1/2 - 2 hours, or for approx. 8
hours if it has been transported on
its side to its final location before
connecting it to the mains.
Switching the appliance on
Open the appliance door.
Press the rocker switch on the right
side underneath the...

To select settings for your appliance
(e.g. to set the temperature, etc),
touch the sensor for the particular
zone of the appliance where you
would like to select the settings.
The applicable sensor will then be
highlighted in yellow, and depending
on the zone, further settings which may
be selected will now appear in the
display.
Depending on which zone you have
selected, you can
– adjust the temperature, or
– select the Super cool function, or
– adjust the humidity levels for the
MasterFresh drawers....

Settings mode
You can select further settings in
settings mode and you can also select
certain appliance functions via the
control panel and adjust the settings.
The settings for the different functions
are described in more detail in the
relevant section of these instructions.
Overview of functions that can be
selected in settings mode:
Function Symbol
To enter or leave settings
mode
To select the
temperature unit
(see The correct
temperature)†
No function selected
To switch the sensor
tone on/off...

Leave your finger on thesensor for
another 4 seconds untilcand the
sensor also appear in the display.
Now touch thesensor repeatedly
untilbappears in the display.
Touch the access sensor again.
By touching thesensor, you can
now select whether the sensor tone is
switched on or off:
0: Sensor tone switched off
1: Sensor tone switched on
–: Return to menu
After selecting a new setting, touch
the access sensor to confirm your
choice.
Touch thesensor repeatedly until
appears in the display.
...

It is very important to set the correct
temperature for storing food in the
appliance. Micro-organisms will cause
food which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these micro-organisms. Reducing
the temperature reduces their growth
rate.
The temperature in the appliance will
rise:
–the more often the door is opened
and the longer it is kept open,
– the more food that is stored in it,
– the warmer the food is which is being
put into it,...

–Touching the sensor once:
adjusts the temperature shown in
1 °C steps.
–Keeping your finger on the sensor:
changes the temperature
continuously.
If the highest or lowest temperature that
it is possible to set is reached, theor
sensor will disappear from the
display.
The temperature display on the
control panel always shows the
requiredtemperature.
When you have adjusted the
temperature,wait for approx. 6 hours
if the appliance is not very fulland
for approx. 24 hours if the appliance
is fullbefore...

Now touch thesensor repeatedly
until†appears in the display.
Touch the access sensor again.
By touching thesensor, you can
now set the temperature to be
displayed in Fahrenheit or Celsius.
†0: Temperature in Fahrenheit
†1: Temperature in Celsius
†–: Return to menu
After selecting a new setting, touch
the access sensor to confirm your
choice.
Now touch thesensor repeatedly
untilcappears in the display.
Touch the access sensor again.
You have now left settings mode.
The door alarm is...