Miele Kf 9757 Id Operating And Installation Instructions

. . . bars light up or flash in the
temperature displays.
Check the temperature displays about
6 hours after switching on the
appliance. Only temperatures within the
range the appliance can display will be
shown.
...F0toF5 in one of the
temperature displays appears.
There is a fault. Call the Service
Department.
. . . the Super freeze indicator light
and the temperature display are both
flashing at the same time.
There is a fault. Call the Service
Department.
. . . the Super freeze indicator light
does...

. . . the interior lighting in the
refrigerator section is not working.
Has the refrigerator door been left open
for too long? The lighting switches itself
off automatically after approx. 15
minutes.
If it also does not come on when the
door is opened briefly, but the
temperature display is working, then
the lighting is defective.
^Call the Service Department.
The LED lighting may only be repaired
or changed by a service technician.
Danger of injury and damage.
Should the cover be damaged or
need to be...

Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creak ...Creaking sounds can be...

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily...

To avoid a hazard due to instability
of the appliance, it must beinstalled
in accordance withthese
instructions.
Location
The appliance should be installed in a
dry, well ventilated room. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
It should not be installed where it is
exposed to direct sunlight or directly
adjacent to a heat-producing appliance...

Ventilation
Air at the back of the appliance gets
warm. The appliance housing unit must
be constructed to allow sufficient space
for ventilation.
A ventilation gap of at least 38 mm
depth must be allowed for behind the
appliance for air to circulate.The air
inlet to the appliance is via the plinth in
the housing unit.
The cross-section of the air inlet and
outlet must be at least 200 cm
2to
ensure that air can circulate without
hindrance. Otherwise the appliance has
to work harder, resulting in an...

Freezer section height Niche height
AB
KF 9757 iD549 1772 - 1788
Building-in dimensions
48
 

The door hinges are set ex-works to
enable the doors to be opened wide.
However, if the opening angle of the
doors needs to be limited for any
reason, the hinges can be adjusted to
accommodate this.
–For example, if the appliance doors
hit an adjacent wall when opened,
the opening angle can be limited to
90°.
^Place the locking pins supplied for
limiting the door opening into the
hinges from above.
The door opening angle is now limited
to 90°.–If you would like the appliance doors
to be cushioned so that...

Before building the appliance in, you
will need to decide on which side the
door is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
^Open both appliance doors.
^
Remove coversa,bandcand
capsdwith a screwdriver.
^
Slightly loosen fixing screwseat the
top, middle and bottom of the
appliance.
^
Push each of...