Miele Kf 9757 Id Operating And Installation Instructions

							^Undo ball jointdusing a spanner
and remove it.
^Stand the appliance doors up one by
one, and slacken the hinges at the
front (the hinges remain open).
^
Remove capsafrom the top and
bottom of each door (if the caps are
not in place, they will have been
supplied separately with the
appliance).
^
Remove screwsbfrom all of the
hinges, and refit each hinge in its
diagonally opposite corner.
Do notclose up the hinges. Danger
of injury.
^
Use a powered screwdriver to secure
the hinges; screwsbare
self-tapping.^Replace capsain the vacant holes
on the opposite side.
To secure the soft-close mechanism
^Place the two doors with the outer
side downwards on a stable surface.
^Screw ball jointdof soft-close
mechanismcinto the new fixing
holes.
^Push tension springainwards
again.
^
Screw mountingbonto the hinge
and tighten securely.
^
Open out soft-close mechanismc
and hook it onto ball jointd.
Changing the door hinging
51
 
						

							^Hang the doors onto the pre-fitted
screws, and push the doors inwards.
^Tighten the screws at the top, middle
and bottom securely.
^Replace coversa,bandc.
^Then replace capsdin the vacant
holes.
^
Replace the locking pins into the top
of the hinges to prevent the doors
opening too far.
Changing the door hinging
52
 
						

							All fitting instructions given are for a
right hand hingedappliance. If you
have converted the appliance to left
hand hinging you will need to adapt
these instructions accordingly.
To install the appliance you will need
the following:
–a cross-slotted screwdriver,
–a selection of Torx screwdrivers,
–a hexagon spanner.
Weight of the furniture doors
Before fitting furniture doors, ensure
that the weight of the door does not
exceed the maximum permitted:
Appliancemax.
weight
of upper
door in
kgmax.
weight
of lower
door in
kg
KF 9757 iD 20 12
Fitting a door which is heavier than
the maximum permitted could
damage the hinges.
Building into a peninsular run
When built into a peninsular run, the
rear of the building-in niche must be
fitted with a kitchen furniture panel.
Aligning the housing unit
The housing unit must be carefully
aligned using a spirit level before
installing the appliance. The unit
corners must be at right angles, as
otherwise the furniture door will not
align correctly with the 4 corners of the
appliance.
Building in the appliance
53
 
						

							Preparing the appliance
^Slide cover stripainto the holder as
shown, with the bumps facing
downwards. The bumps will fit into
keyhole slotsb.
^Position the mains electricity cable so
that the appliance can be connected
easily once installed.
^
Secure fixing bracketsc(supplied)
to the appliance doors by screwing a
hexagon screwdinto the pre-drilled
holes.
(With large furniture doors, attach a
third pair of fixing bracketscin the
handle region of the doors).^Push the appliance two-thirds of the
way into its niche.
When doing this, make sure that the
mains cable does not get trapped.
With 16 mm thick unit walls:
^Clip spacerseonto the top hinges
and spacersfonto the bottom
hinges.
Building in the appliance
54
 
						

							^Open both appliance doors.
^Using a screwdriver, remove cover
gfrom the top corner of the
appliance.
^
Fit coverhonto fixing bracketi.
^
Secure fixing bracketito the top of
the appliance with screwsj
(M5 x 15).^Fit coverkonto fixing bracketl.
^Secure fixing bracketlto the
bottom of the appliance with screws
m(M5 x 15).
^Carefully remove the protective foil
from sealing stripn.
^Apply the sealing strip to the side of
the appliance on which the door is
opened so that it is flush with the
front edge of the appliance.
Fit the sealing strip so that it meets
up with the lower edge of top cover
hand then cut the sealing strip
2-3mmabove bottom fixing bracket
l.
^
Push the appliance into the niche
until covershandktouch the front
edge of the side walls of the housing
unit.
Building in the appliance
55
 
						

							Building in the appliance
–With 16 mm thick walls:
The spacers should touch the front
edge at the top and bottom of the
side walls of the housing unit, detail
a.
–
With 19 mm thick walls:
The front edges of the top and
bottom hinges sit flush with the front
edge of the housing side walls, detail
b.
^
Make sure that the covers on the top
and bottom fixing brackets sit flush
with the front edges of the housing
unit side walls, detaild.
This will create a gap all round of
42 mmto the front edges of the
housing unit side walls.On furniture with door fittings (e.g.
stubs, seals etc)the dimension of
these must be taken into account when
making sure there is a gap all round of
42 mm.
^Pull the appliance forwards by the
dimension of the door fitting to keep
the gap at 42 mm all round.
The hinges and the covers will now
protrude by the dimension of the door
fitting.
Tip: Remove the door fittings. This will
ensure that the doors are flush with the
surrounding kitchen unit furniture doors.
If the all round gap of 42 mm is not
maintained between the appliance
casing and the front edge of the
housing unit side wall the doors may
not shut properly.
This could lead to a build-up of ice
and condensation and also cause
operational faults.
^
Align the appliance height on both
sides by altering the adjustable feet
using the spanner suppliedc.
Building in the appliance
56
 
						

							Securing the appliance in the
niche
^Press the appliance against the
housing unit on the hinge side.
^To fix the appliance to the housing
unit at the top and bottom, screw the
long4x20mmchip board screwsa
into the hinges at the top and bottom.^Loosen screwsbon the top and
bottom fixing bracketsc.
^Press fixing bracketcagainst the
side wall and tighten screwsb.
^
Attach fixing bracketcto the
housing unit side wall with screwsd.
Drill holes in the housing unit side
walls if necessary.
^
Break off the protruding end of top
covere, turn the cover around and
fit it on top fixing bracketc.
^
Fit oblong coverfonto top fixing
bracketc.
Building in the appliance
57
 
						

							^Break off the protruding end of
bottom covere. It is no longer
required.
^Fit angled covergonto bottom fixing
bracketc.
^Close the appliance doors.
Fitting the furniture doors
^
A gap of 8 mmamust be set
between the appliance door and the
central fixing bracket.
^
Push fitting aidsbup to the height of
the furniture door: the lower edge X
of the fitting aids must be at the same
height as the upper edge of the
furniture door being fitted (see-on
the diagram).
^
Undo nutscand take fixing bracket
doff together with the fitting aids.^Using a pencil, lightly mark a line
down the centre of the inside of the
furniture door.
^Hang fixing bracketdwith the fitting
aids onto theinsideof the furniture
door. Align the fixing bracket
centrally.
^Attach the fixing bracket securely
using at least 6 short4x14mm
chipboard screwsb. (On cassette
doors only use 4 screws on the
edges).
^
Pull the fitting aids upwards to
remove themf.
^
Turn them around and fit them into
the middle slots on fixing bracketg
for safe keeping.
Building in the appliance
58
 
						

							^Hang the furniture door onto
adjusting boltsh.
^Loosely attach nutscon the
adjusting bolts.
^Close the door and check the
distance between the door and
neighbouring furniture doors.
^Align to match neigbouring doors if
necessary:
Side adjustments X are made by
sliding the furniture door, and height
adjustments Y by turning adjusting
boltshwith a screwdriver.
^
Tighten nutsc.Securing the appliance doors to the
furniture doors:
^Drill fixing holesain the furniture
doors and screw in the4x14mm
screwsb.
Make sure the two metal edges are
alligned (SymbolII).
– Align depth Z on the furniture door:
Loosen screwscat the top of the
appliance door, and loosen the
hexagon-headed screwdat the
bottom of the fixing bracket. By
moving the furniture doors, create a
gap of 2 mm between the furniture
doors and the front edge of the
housing unit.
Building in the appliance
59
 
						

							^Close both of the doors, and align
them with the neighbouring furniture
doors.
^Whilst counterholding adjusting bolts
gwith a screwdriver, tighten nutsa
on the appliance doors with ring
spannerf.
^
Cover striphmust be completely
hidden in the niche, and must not
protrude.
^
Tighten all screws again.^Replace top coveri, and snap it
into place.
^Replace side coversj, making sure
they snap into place.
^Replace side coversk, making sure
they snap into place.
Building in the appliance
60