Miele Pw 5065 Operating Manual

							Drainage
There are two drainage options for this
machine:
Drain valve
The machine is drained with a
motorized drain valve. A connection
can be made to an on-site floor drain
(gully with an air gap) on an angle.
Drain pump
The wash water is drained using a
pump with a 3 ft (1 m) delivery height.
Make sure there are no kinks in the
drain hose. The elbow on the end of the
drain hose can be turned or removed if
necessary.
Possible connections:
1. Directly into a sink:Hook the hose
over the edge of the sink and secure
it firmly (e.g. by tying the hose to the
water faucet).
2. To a stand pipe:Place the drain
hose into a 1
1/2 (4 cm) stand pipe
and secure it firmly.
3. To a floor drain:The machine is
equipped with an air gap/
anti-siphoning system so that no
minimum drain height is required.If necessary the drain hose can be
extended up to 16’ 5 (5 m). The hose
extension can be purchased from your
Miele dealer or Miele.
The drain pump must be replaced for
drain heights over 3 ft (1 m). The
maximum allowable drain height is 5 ft
11 in (1.8 m). A stronger pump for
these heights can be purchased from
your dealer or Miele.
Installation
51
 
						

							Electrical connection
,This installation should be
performed by an experienced and
qualified technician, in accordance
with local codes and regulations.
The washer comes with a power cord
without a plug.
The machine is supplied as standard
for connection to a 208 V, 60 Hz, 20 A,
2-phase electrical supply*.
For extra safety it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA.
The machine must only be connected
to the voltage and frequency shown on
the data plate.
,*To convert the machine to
another electrical connection,
please read the converting manual
on the wiring diagram inside the
washer. The conversion must be
performed by a Miele Service
Technician. Additionally the Heating
level setting must be adjusted.
,Do not install devices to
automatically turn the washer off,
i.e. a clock timer.If the machine is hard wired, two 20 A
circuit breakers must be provided
on-site. Switches with a contact gap of
more than 3 mm are valid as
separators. All components must be
CSA or UL approved.
Installation
52
 
						

							Height 337/16 (85 cm)
Width 23
7/16 (59.5 cm)
Depth 283/8 (72 cm)
Depth with the door open 44
1/8 (112 cm)
Weight 236 lb (107 kg)
Maximum floor load 2778 Newton (approx. 278 kg)
Capacity 13.2 lbs (6.5 kg) dry laundry
Fuse rating see data plate
Rated load see data plate
Fuse rating see data plate
Noise level during spinning
(Noise emission 3. GSGV)< 70 dB(A)
Minimum water flow pressure 14.5 psi (1 bar)
Maximum water pressure 145 psi (10 bar)
Length of intake hose 5’3 (1.6 m)
Length of power cord 5’3 (1.6 m)
Drain height maximum (Drain pump) 3’3 (1 m)
Light bulb for drum light Type G4 (5 Watts/12 Volt)
Technical Data
53
 
						

							Disposal of the packing
materials
The cardboard box and packing
materials protect the appliance during
shipping.
To prevent suffocation of children
ensure that any plastic wrapping, bags,
etc. are disposed of safely and kept out
of the reach of children.
Please recycle.
Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure that the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet, cut
off its power cord and remove any
doors to prevent hazards.
Help to protect the environment
54
 
						

							Menu SettingsJ
to adjust standard settings
The washer controls can be adjusted to changing demands through the settings
menu.
 
						

							Accessing the "Settings"J
^Turn the program selector to Finish.
The main menu shows.
12:03
Selecting a program
SettingsF
^Confirm with OK.
^The Settings menu is selected.
CBackA
LanguageF
Suds cooling
^Set the desired setting with the
buttons+/–and confirm with OK.
Leaving the Settings menu
^Select Back and confirm with OK.
The display shows the main menu.
LanguageJ
The display contents can be shown
in different languages.
The displayed language can be
changed by the sub-menu
LanguageJ.
The flag behind the word LanguageJ
is a guide to find the settings menu in
case a foreign language is selected.
The selected language is marked with a
check.
If the language setting was changed, it
is only valid for the current wash
program. Once the program ends, the
display will show the language which is
set under Settings - Supervisor level.
Suds cooling
Cold water is added at the end of
the main wash to cool the wash
water.
The wash water cooling is carried out
when a wash temperature of 158°F
(70°C) or more is selected.
The wash water cooling should be
activated when the drain hose is hung
into a sink, to prevent scalding
The wash water cooling is factory set
on.
SettingsJ
56
 
						

							Time of day
This selection allows the clock to be
shown as 24 hours, 12 hours or not
at all. The time of day is also set
here.
If the clock is not selected the delay
start can only be shown as a 24 hour
timer. The display will show the timer
counting down until the start of the
program but not the current time of day.
Selecting the clock display
^Select the desired clock display and
confirm.
The display shows the clock setting.
Set the time of day
^Set the hours with the buttons+/–
and confirm with OK. Repeat with
setting the minutes and confirm. The
display changes to Settings.
Display contrast
The contrast of the display can be
set at ten different levels.
It is factory set to Setting 4.
The contrast changes immediately
when a different level is selected.
Display brightness
The brightness of the display can be
set at ten different levels.
It is factory set to Setting 5.
The brightness changes immediately
when a different level is selected.
SettingsJ
57
 
						

							Standby
The display goes out after 10
minutes and the Start button
flashes slowly to save energy.
Two options can be selected:
On
The display will go into standby mode:
–if no program is selected after the
machine is turned on.
–after a program has started.
– at the end of a program.
Not in current prog.
(factory default)
The Standby function will be turned on
if no program was selected after the
machine was turned on.
By turning the program selector or
pressing any button the display is
turned on again.
Memory
The Memory function remembers the
addition of an extra feature to a
program, a change in spin speed or
the temperature the next time that
program is selected.
Once the wash program is selected
again the washer shows the saved
options.
The Memory function is factory set to
off.
SettingsJ
58
 
						

							The menu "Settings - Supervisor
level" has to be "activated" by a
Miele service technician or dealer.
The menu Settings (except
LanguageJ) is locked with a code
to prevent unwanted access.
CBackA
FLanguageF
Supervisor level
^Select the Supervisor level and
confirm.
CBackA
XEnter code
^Select the code and confirm.
Entering the code
A three digit code must be entered. On
delivery the code is:0 0 0.
0__
Enter code
^
Enter the first digit with the+button.
Confirm with OK.
^
Enter the second and third digit.
Confirm each with OK.
W
Entry OK.
Menu opened.
The user is now in the supervisor level.
The following settings can now be
changed.
Change the code to prevent
unwanted access to the settings.
Menu Settings - Supervisor level
59
 
						

							LanguageJ
The display contents can be shown
in different languages.
The fixed language selection can be
set in the sub-menu LanguagesJ.
^Select the desired language and
confirm with OK.
Supervisor level
The access code for the operator
level can be changed.
^Enter the old code.
^Enter the new code.
Once the new code is confirmed, the
beginning of the Settings menu will
appear.
Auto load control
If the Auto load control is turned off
the program will run as if for a full
load.
The machine comes factory set with
this option on.
Pre-wash water
The water type (hot/cold) for the
pre-wash can be selected (except
for the program Curtains). The hot
water intake will be only accessible
at a wash temperature of 86°F
(30°C) or higher.
The machine comes factory set with
water type hot.
Main wash water
The water type for the main wash
can be selected (except for the
programs WOOLLENS and
Curtains). The hot water intake will
only be accessible at a wash
temperature of 86°F (30°C) or
higher.
The machine comes factory set with the
water type hot selected.
If the washer is not connected to hot
water, the program running times will
be extended and vary from the
displayed remaining times.
Menu Settings - Supervisor level
60