Miele T 7944 C Manual
Have a look at the manual Miele T 7944 C Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 171 Miele manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Extending the cooling down time The cooling down phase which takes place before the end of a programme can be extended by 5 or 10 minutes, if required. This makes the garments easier to handle. The cooling down time can only be extended for programmes with drying levels. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton five times. – TheLow temperatureindicator light will flash seven times briefly. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Cooling down time not extended (factory default setting) iCooling down time extended by five minutes (theAutomatic plusindicator light will also flash once). 2Cooling down time extended by ten minutes (theAutomatic plusindicator light will also flash twice). Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 51
Standby To save energy, the display and the programme sequence/check lights go out after 10 minutes and the Start/Stopbutton starts flashing slowly. To come out of standby mode Turn the programme selector or press a button. Neither will have any effect if a programme is running. On The standby function is activated and the display and programme sequence/check lights will go out after 10 minutes: – if a programme is not selected after the dryer has been switched on. – after a programme has started. They will, however, come on for 10 minutes after a delay start time has counted down, at the end of the programme or the end of the anti-crease phase. The buzzer (if selected ) will sound for 10 minutes at the end of the programme.Factory default. Not in current programme As described under On. However, the display and programme sequence/check lights will stay on after the programme has started and remain visible during the programme. Off The display and programme sequence/check lights will stay on while the dryer is switched on. Follow the steps ( ,,...) to programme and store in memory. See next page. Programmable functions 52
Before you begin, ensure that: –The tumble dryer is switched off. –The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton six times. – TheLow temperatureindicator light will flash 8 times briefly. Anumberto show which option is selected will appear in the display alternating with the letterP. 0On IFactory default setting. Not in current programme (theAutomatic plusindicator light will also flash once). 2Off (theAutomatic plusindicator light will also flash twice). Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 53
Memory function The electronics will memorise any extra options selected for a programme. The duration selected for the Warm air or Cool air timed drying programmes will also be stored in memory. These settings will be selected automatically the next time the programme is chosen. You can either accept these or change them by pressing the appropriate button. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton seven times. – TheLow temperatureindicator light will flash 9 times briefly. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Memory deactivated (factory default setting) IMemory activated (theAutomatic plusindicator light will also flash) Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 54
Clean out airways indicator Fluff should be removed after drying. TheClean out airwaysindicator will remind you to clean the filters when a certain amount of fluff has collected in the filters. You can decide at what level of fluff this reminder should be given. You will have an idea of how often this should be done after a few drying programmes. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton eight times. – TheLow temperatureindicator light will flash on and off slowly once. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Clean out airwaysindicator light deactivated IClean out airwaysindicator light comes on when there is a heavy build-up of fluff (theAutomatic plusindicator light will also flash once). 2Factory default setting (theAutomatic plusindicator light will also flash twice). 3Clean out airwaysindicator light comes on when there is only a light build-up of fluff (theAutomatic plusindicator light will also flash three times). Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 55
Keypad tone An audible tone sounds each time a button is pressed. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: –The tumble dryer is switched off. –The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton nine times. – TheLow temperatureindicator light will flash on and off slowly once and then on and off quickly once. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Keypad tone deactivated (factory default setting) IKeypad tone activated (theAutomatic plusindicator light will also flash) Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 56
Adjusting the dryers electronics for very soft water In some areas of the UK, water is extremely soft which can affect the sensitivity of the control electronics. If the dryer is installed in an area of very soft water, you should contact your local water supplier for information and advice regarding water hardness and water conductivity. If the water conductivity is less than 150 µS, the following programmable function will need to be activated. Important. This programmable function should not be activated if, despite the water being extremely soft (as would be the case if a water softener were used), its conductivity is greater than 150 µS. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton ten times.–TheLow temperatureindicator light will flash on and off slowly once and then on and off quickly twice. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Factory default setting IAdjusted for very soft water (theAutomatic plusindicator light will also flash) Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 57
Extending the range of the drying levels You can extend the range of the drying levels for many of the programmes: Machine iron+ (drier than Machine iron). Slightly dry (drier than Hand iron). Normal+ (drier than Normal). This programmable function is only available for programmes with drying levels. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton eleven times. – TheLow temperatureindicator light will flash on and off slowly once and then on and off quickly three times. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Factory default setting IDrying level range extended (theAutomatic plusindicator light will also flash). Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. To select the extended drying level Select a programme. Press the drying level button repeatedly until one or two indicator lights come on. – Indicator lightsExtra dryandNormal = Normal+ – Indicator lightsNormalandHand iron= Slightly dry – Indicator lightsHand ironand Machine iron= Machine iron+ Programmable functions 58
M.-Nr. 07 851 060 / 02Alteration rights reserved/3611