Miele T 8823 C Manual

							Extending the drying level for
the Minimum iron
programme
The electronics of this dryer ensure a
very effective and energy-efficient
drying process.
You can, however, extend the range
of the drying level in this programme.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
once.
–
TheLow temperatureindicator light
will briefly flash on and off twice.
The option selected will be displayed
by anumberwhich will alternate with
P.
0The drying level will be damper.
IStandard setting
(TheAutomatic plusindicator light
will also flash once.)
2The drying level will be drier.
(TheAutomatic plusindicator light
will also flash twice.)
Pressing theStart/Stopbutton
switches from one to the other.
Switch the dryer off.
The settings have been changed. You
can alter the settings again at any time.
Control
Repeat steps
to.
Switch the dryer off after step.
Programmable functions
51 
						

							Anti-crease setting
Helps prevent creasing if laundry is
not normally removed immediately
after the end of a programme.
Anti-crease
–is set as a standard setting. You can
shorten the time or switch it off
completely.
–can be used for all programmes,
exceptWoolens handcare.
–should always be switched on.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
twice.
–
TheLow temperatureindicator light
will briefly flash on and off three
times.
The option selected will be displayed
by anumberwhich will alternate with
P.
0Anti-crease deactivated.
I1 hour Anti-crease
(TheAutomatic plusindicator light
will also flash once.)
2Default setting. 2 hours
Anti-crease.
(TheAutomatic plusindicator light
will also flash twice.)
Pressing theStart/Stopbutton
switches from one to the other.
Switch the dryer off.
The settings have been changed. You
can alter the settings again at any time.
Control
Repeat steps
to.
Switch the dryer off after step.
Programmable functions
52 
						

							Altering the volume of the
buzzer
The buzzer has two volumes.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
–The dryer is switched off.
–The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
three times.
– TheLow temperatureindicator light
will briefly flash on and off four times.
The option selected will be displayed
by anumberwhich will alternate with
P.
0Default setting. Normal buzzer
ILoud buzzer
(TheAutomatic plusindicator light
will also flash.)
Pressing theStart/Stopbutton
switches from one to the other.
Switch the dryer off.
The settings have been changed. You
can alter the settings again at any time.
Control
Repeat steps
to.
Switch the dryer off after step.
Programmable functions
53 
						

							Extending the drying level for
the Automatic plus
programme
The electronics of this dryer ensure a
very effective and energy-efficient
drying process.
You can, however, extend the range
of the drying level in this programme.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
four times.
–
TheLow temperatureindicator light
will briefly flash on and off six times.
The option selected will be displayed
by anumberwhich will alternate with
P.
0The drying level will be damper.
IStandard setting
(TheAutomatic plusindicator light
will also flash once.)
2The drying level will be drier.
(TheAutomatic plusindicator light
will also flash twice.)
Pressing theStart/Stopbutton
switches from one to the other.
Switch the dryer off.
The settings have been changed. You
can alter the settings again at any time.
Control
Repeat steps
to.
Switch the dryer off after step.
Programmable functions
54 
						

							Extending the cooling down
time
The cooling down phase which takes
place before the end of a programme
can be lengthened if required. This
makes the garments easier to handle.
The cooling down time is only available
for programmes with drying levels.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
five times.
–
TheLow temperatureindicator light
will briefly flash on and off seven
times.
The option selected will be displayed
by anumberwhich will alternate with
P.
0Default setting
IThe cooling down time will be five
minutes longer.
(TheAutomatic plusindicator light
will also flash once.)
2The cooling down time will be ten
minutes longer.
(TheAutomatic plusindicator light
will also flash twice.)
Pressing theStart/Stopbutton
switches from one to the other.
Switch the dryer off.
The settings have been changed. You
can alter the settings again at any time.
Control
Repeat steps
to.

Switch the dryer off after step.
Programmable functions
55 
						

							Standby
To save energy, the display goes out
after 10 minutes and the indicator
light for theStart/Stopbutton will start
flashing slowly.
Reactivate from Standby
Turning the programme selector or
pressing one of the buttons switches
the display back on again. This will
not alter a running programme.
On
Standby is activated:
– if a programme is not selected after
the machine has been switched on.
– after a programme has started.
However: The display will switch on for
10 minutes if Delay start has finished,
after the end of a progamme or the
anti-crease cycle.
The buzzer (if selected) will sound for
10 minutes after the end of a
progamme.Factory default settings. Not in
current programme
As in On.
But: The display will not switch off
during a programme.
Off
The display will not switch off during a
programme.
Follow steps (
,,...) to
programme and store in memory.
See the next page.
Programmable functions
56 
						

							Before you begin, first ensure that:
–The dryer is switched off.
–The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton six
times.
– TheLow temperatureindicator light
will briefly flash on and off eight
times.
The option selected will be displayed
by anumberwhich will alternate with
P.
0On
IFactory default settings. Not in
current programme
(TheAutomatic plusindicator light
will also flash once.)
2Off
(TheAutomatic plusindicator light
will also flash twice.)
Pressing theStart/Stopbutton
switches from one to the other.
Switch the dryer off.
The settings have been changed. You
can alter the settings again at any time.
Control
Repeat steps
to.
Switch the dryer off after step.
Programmable functions
57 
						

							Memory function
The electronics will memorise any
Extra options selected for a
programme. The duration selected
for the timed drying programmes will
also be stored in memory.
These settings will be selected
automatically the next time the
programme is chosen. You can either
accept these or change them by
pressing the appropriate button.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
seven times.
–
TheLow temperatureindicator light
will briefly flash nine times.
The option selected will be displayed
by anumberwhich will alternate with
P.
0Default setting. Memory
deactivated.
IMemory.
(TheAutomatic plusindicator light
will also flash.)
Pressing theStart/Stopbutton
switches from one to the other.
Switch the dryer off.
The settings have been changed. You
can alter the settings again at any time.
Control
Repeat steps
to.
Switch the dryer off after step.
Programmable functions
58 
						

							Clean out airways indicator
Fluff should be removed after drying.
The Clean out airways indicator will
remind you toClean the filterswhen a
certain amount of fluff has collected
in the filters. You can decide at what
level of fluff this reminder should be
given.
You will have an idea of how often this
should be done after a few drying
programmes.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
eight times.
–
TheLow temperatureindicator light
will flash on and off slowly once.
The option selected will be displayed
by anumberwhich will alternate with
P.
0TheClean out airwaysindicator
light is deactivated.
ITheClean out airwaysindicator
light will come on when there is a
heavy build-up of fluff
(TheAutomatic plusindicator light
will also flash once.)
2Default setting
(TheAutomatic plusindicator light
will also flash twice.)
3TheClean out airwaysindicator
light will come on when there is
only a light build-up of fluff
(TheAutomatic plusindicator light
will also flash three times.)
Pressing theStart/Stopbutton
switches from one to the other.
Switch the dryer off.
The settings have been changed. You
can alter the settings again at any time.
Control

Repeat steps
to.

Switch the dryer off after step.
Programmable functions
59 
						

							Keypad tone
An audible tone sounds each time a
button is pressed.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
–The dryer is switched off.
–The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
nine times.
– The indicator lightLow temperature
will flash on and off slowly once and
will then flash on and off quickly
once.
The option selected will be displayed
by anumberwhich will alternate with
P.
0Default setting. Keypad tone
deactivated.
IKeypad tone activated
(TheAutomatic plusindicator light
will also flash.)
Pressing theStart/Stopbutton
switches from one to the other.
Switch the dryer off.
The settings have been changed. You
can alter the settings again at any time.
Control
Repeat steps
to.
Switch the dryer off after step.
Programmable functions
60