Miele W 2809 I Operating Instructions

Matching the fascia panel to
the height of adjacent drawer
fronts
Spacer bars
The fascia panel can be aligned with
the drawer fronts by adjusting the
spacer bars.
^Using a socket spanner, turn
clockwise or anti-clockwise until the
required height is reached.
If necessary individual bars can be
removed or more added.
^
To do this, use the socket spanner to
loosen the nuts.
An adapter kit with spacer bars and
longer screws can be ordered as an
optional accessory. This can be used to
add spacer bars from...

Fitting the front panel
The machine front can be fitted with a
door panel to match other kitchen units.
If fitted in a Miele kitchen, the door
panel can be ordered pre-drilled with
the necessary fixing holes as an
optional accessory.
If fitted in a non-Miele kitchen, a
suitable panel will have to be drilled
to suit by a qualified kitchen fitter.
See Fitting a door front panel made
by another manufacturer for details
on preparing and drilling the fixing
holes.
Front panel dimensions
Width
: 592 - 596 mm...

Fitting a door front panel made
by another manufacturer
Preparing the front panel
AMeasure distanceXfor drilling the
hinge holes.
–with spacer bars:
– without spacer bars:
(the front panel must be
correspondingly higher)BMark the two hinge holes and the
four smaller holes as shown in the
diagram.
For left hand hinging only:
–front panel shown decor side face
down, upper edge at the bottom:
if width (b) increases, measurementa
must also be increased
b= 592 mmNa= 21.5 mm
b= 593 mmNa= 22.0 mm
b= 594 mmNa=...

For right hand hinging only
–front panel shown decor side face
down, upper edge at the bottom:
if width (b) increases, measurementa
must also be increased
b= 592 mmNa= 21.5 mm
b= 593 mmNa= 22.0 mm
b= 594 mmNa= 22.5 mm
b= 595 mmNa= 23.0 mm
b= 596 mmNa= 23.5 mm
The heightHof the door front panel
corresponds to the door height of the
adjacent units.CDrill the two hinge holes (C35 mm/
15.5 mm deep) in the back of the
front panel.
DNext, drill the four smaller holes
(C7 mm/10 mm deep) in the back of
the front...

Fitting a plinth facing
The gap between the lower edge of the
washing machine plinth and the floor
can be closed up using a suitable
kitchen furniture plinth facing.
The washing machine plinth has a
special groove in which a plinth facing
can be fitted.
Plinth facing dimensions
Length
: 592 - 596 mm
Thickness
: 8 mm
Height (
H): The plinth facing height
must be calculated after aligning the
height of the machine with the screw
feet or after fitting the raising kit(s).Installation
^Calculate height (H)...

The Miele water protection
system
The Miele water protection system
protects the washing machine from
water damage.
The system consists of three main
components:
1) the inlet hose
2) the electronic unit and the washing
machine housing
3) the drain hose
1) Inlet hose
The inlet hose can withstand
pressure of more than 7,000 kPa.
2) Electronic unit and washing
machine housing
– Sump
Any leaking water is collected in a
sump in the base of the machine. A
float switches off the safety valves,
preventing any...

Connection to the water supply
The machine should be connected to a
mains water supply in accordance with
local and national safety regulations.
The German authorities do not require it
to have a non-return valve as the
washing machine has been designed
to comply with DIN regulations.
The machine is designed to operate
with a flow pressure of between
100 kPa and 1,000 kPa. If it is higher
than 1,000 kPa it is essential to fit a
pressure reducing valve.
Connection to the mains water supply
should...

Connection to the drainage
system
The machine drains via a drain pump
with a delivery head of 1 metre*.
The drain hose must not be kinked as
this restricts drainage. The swivel elbow
at the end of the hose can be turned in
either direction, or can be detached if
required, with a sharp twist and pull.
If required, the drain hose can be
extended to a length of 5 m. The
necessary parts can be purchased
from the Miele Spare Parts Department
or your Miele dealer.
* For a delivery head of more than 1 m
(up to...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person, in strict accordance with
current national and local safety
regulations (BS 7671 in the UK).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply.
Please ensure the connection data
quoted on the data plate match the
household mains...

Load Consumption data
Energy Water Duration
in kWh in litres Short Normal
Cottons95°C 5.0 kg 1.70 42 2 h 09 min
60°C1)5.0 kg 0.85 42 1 h 49 min
60°C 2.5 kg 0.70 36 1 h 03 min
40°C1)5.0 kg 0.52 48 1 h 59 min
40°C2)2.5 kg 0.36 36 59 min
Minimum iron40°C1)2.5 kg 0.44 49 59 min 1 h 19 min
Delicates30°C 1.0 kg 0.33 65 49 min 59 min
Woollens/30°C 2.0 kg 0.23 39 – 39 min
Silks/30°C 1.0 kg 0.25 39 – 36 min
Express40°C 2.5 kg 0.30 30 – 30 min
Automatic40°C 3.0 kg 0.35 - 0.50 40 - 55 – 1 h 18 min
Shirts60°C 1.5 kg...