Mitsubishi Electric CP3800DW User Manual
Have a look at the manual Mitsubishi Electric CP3800DW User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 561 Mitsubishi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 6
Italian
Con la presente Mitsubishi Electric Corporation dichiara che questo CP3800DW è\
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla
direttiva 1999/5/CE.
Spanish
Por medio de la presente Mitsubishi Elec tric Corporation declara que el CP3800DW
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
Portuguese
Mitsubishi Electric Corporation declara que este CP3800DW está conforme...](http://img.usermanuals.tech/thumb/3285/37510/w64_Mitsubishi_Electric_CP3800DW-5.png "Page 6
Italian
Con la presente Mitsubishi Electric Corporation dichiara che questo CP3800DW è\
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla
direttiva 1999/5/CE.
Spanish
Por medio de la presente Mitsubishi Elec tric Corporation declara que el CP3800DW
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
Portuguese
Mitsubishi Electric Corporation declara que este CP3800DW está conforme...")
Setting Up the Printer Setting Up the Printer S e S ett t i t n i g n g Up U p th t e h e Pr P ri n i n te t e r r P P a a p p e e r r a a n n d d R R i i b b b b o o n n Type 8inch Paper Width: 203mm Ribbon Width: 210mm CAUTION ･ Set the paper and ribbon without putting them directly on the work surface. Any dust or dirt could get inside the printer and adversely affect the print quality. Downloaded From ManualsPrinter.com Manuals
Setting Up the Printer Setting Up the Printer S e S ett t i t n i n g g Up U p th t h e e Pr P ri n i n te t e r r S S e e t t t t i i n n g g t t h h e e M M e e d d i i a a 1. Release the Open Lever, and pull out the mechanism unit . Open Lever 2. Open the Paper Release lever. Paper Release Lever 3. Remove the scrap box Scrap Box 4. Remove the entire paper cassette unit. Downloaded From ManualsPrinter.com Manuals
Setting
Up
the
Printer
Setting
Up
the
Printer
S
e
S ett
t i
t n
i n g
g Up
U p th
t h e
e Pr
P ri n
i n te
t e r
r
5. Install the new roll of paper on the paper holder. When installing it, make sure there are no gaps between the paper and the holder.
Make sure the paper is not sticking out. If the end of the roll is uneven (with paper sticking out), remove it from
the holder, and flatten it.
Check for uneven ends
No gaps
○
×
×
Check for uneven ends
6. Set the paper holder into the paper cassette. (Set it firmly all the way in)
Set the paper in the direction indicated below.
Paper direction
Seal
Downloaded From ManualsPrinter.com Manuals
Setting
Up
the
Printer
Setting
Up
the
Printer
S
e
S ett
t i
t n
i g
n g U
Up
p th
t e
h e Pr
P ri n
i n te
t r
e
r
7. Remove the tape, and advance the roll as indicated by the arrow. Set the end of the paper about 5mm beyond the roller. When doing this, insert the paper straight along the seal. If it isn’t inserted straight, the paper will
be crooked, which could cause white line on the edges of the print, ribbon wrinkles, and register slippage.
Path of the paper
As seen from above
○ ×
8. Set the paper cassette into the printer.
Downloaded From ManualsPrinter.com Manuals
Setting Up the Printer Setting Up the Printer S e S ett t i t n i n g g Up U p th t h e e Pr P ri n i n te t e r r 9. Turn the paper in the direction of the arrow. Wh en it is advanced enough, the buzzer will beep, and the flashing LED (orange) will go out. It is easier to set if the paper is turned while securing the holder with one hand. 10. Set the scrap box, and close the cover. The printer will not operate without the scrap box. If the mechanism unit is closed without the scrap box attached, there will be a “No Scrap Box Error”, and the LED will flash (red). CAUTION ･ The printer will not operate without the scrap box attached. ･ When the scrap box is removed, do not insert your fingers in the cutter at the top. They could be cut or severed. ･ As prints are cut, the scrap box fills with scrap paper. Be sure to empty it when you change the pape r and ribbon. If it becomes over-fill ed with scraps, it could cause problems with the printer. Downloaded From ManualsPrinter.com Manuals
Setting Up the Printer Setting Up the Printer S e S ett t i t n i n g g Up U p th t h e e Pr P ri n i n te t e r r 11. Set the new ribbon into the ribbon cassette. Advance the ribbon in the direction of the arrow, and take up any slack. Set it with the supply side in front. 13.Close the mechanism unit. *When the mechanism unit is closed, the printer will run initialization (4 blank sheets will be fed out). However, if the power is turned ON after the paper is set, it won’t run the initialization. By running initialization, the dirty outer layer of paper is cut off. *In order to facilitate media color adjustment, media type recognition, and print quantity management, an IC chip is built into the ink ribbon. Media without an IC chip, which has not been evaluated and cleared, may not function properly. (If correct data cannot be read from the IC chip, an alarm will sound. In this case, in order to protect the printer, it will lower the concentration for printing.) *Please change the media as a set, because the IC chip for each ribbon has unique information. Otherwise, errors could occur. Supply Take Up Supply side Set here CAUTION ・ Replace the ribbon and paper as a set to avoid problems later. Downloaded From ManualsPrinter.com Manuals
Trouble-shooting T ro uble -s hoo tin g E E r r r r o o r r D D i i s s p p l l a a y y s s Power Ribbon Paper Error The flashing LED indicates the printer status LED display Status Power Ribbon Paper Error Solution Refer to Paper End *1 ● Put in a new roll of paper P.12 Ribbon End *1 ● Put in a new roll of ribbon P.16 Door is Open (no paper) ● Set the paper properly and close the mechanism unit P.12 Door is Open ● Close the mechanism unit P.16 No Scrap Box ● Set the scrap box P.15 Paper Error ● ● ● Free the paper, and reset it correctly P.18 Ribbon Error ● ● ● Fix the ribbon, and set it correctly P.20 System Error *2 ● ● Re-boot the printer (turn off, then on) - Head Cool Down The head is cooling off (auto-recovery) - *● indicates lit, indicates flashing, and blank is not lit *1 Exchange the paper and ribbon as a set. *2 If the system error cannot be corrected, contact the dealer. Downloaded From ManualsPrinter.com Manuals
Trouble-shooting Trouble-shooting T r T o r u o b u b le l e -s - sh o h o o o ti t n i n g g S S o o l l v v i i n n g g M M e e d d i i a a E E r r r r o o r r s s 1. Pull out the mechanism unit. 2. Remove the ribbon cassette. a. If the paper is jammed: 1. Pull any paper remaining in the printer in the direction shown, and cut off any wrinkled or partially printed areas evenly with scissors. Printing over an already printed area will cause the ribbon to stick, and the paper will jam again. When pulling the paper out, pull it slowly. Application of too much force could damage the printer. CAUTION ・ Please be careful not to hurt yourself or damage anything on the edges of the printer. Downloaded From ManualsPrinter.com Manuals
Trouble-shooting
Trouble-shooting
T r
T o
r o ub
u b le
l e -
-s h
s o
h o o
oti
t n
i g
n g
2. Remove the scrap box, and rewind the paper.
3. Cut off any partially printed, wrinkled, or otherwise inferior paper evenly with a pair of scissors, and
reset the paper. If wrinkles or partially printed ar eas are left, it could cause the paper to jam again.
Cutting the paper
Then follow the methods as for setting the media.
○ ×
Downloaded From ManualsPrinter.com Manuals
T T r r o o u u b b l l e e - - s s h h o o o o t t i i n n g g b. If the ribbon is pulled into the mechanism: 1. Cut the ribbon. 2. Carefully remove any ribbon remaining in the mechanism. Any pieces of ribbon left inside the mechanism could affect print quality. In this case, clean the platen roller see P.22 3. Reattach the ribbon with cellophane (or similar) tape. Tape 4. Rotate the up-take ribbon several times until the tape is out of sight. Take care that there is no slack in the ribbon. Then, refer to a. If the paper is jammed . Downloaded From ManualsPrinter.com Manuals