Mitsubishi Electric Diamond Pro 730 Service Manual



- 1-9 -
ENGLISH
x : Available
MOIRE CANCEL LEVELXX
CLAMP PULSE POSITIONX
FACTORY PRESET---
HORIZ-CONVERGENCEXXX
VERT-CONVERGENCEXXX
FACTORY PRESET---
DEGAUSS---
POWER SAVEXXX
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaCONTROL LOCKX
OSD POSITIONXXX
OSD TURN OFFXXX
DIAGNOSIS---
LANGUAGEX
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaAUTO SAVEX
ALL RESET---
FACTORY PRESET---
Group
IconPress the Minus ButtonItem Item
IconPress the Plus Button
To adjust the horizontal beam alignment on the full screen...



- 1-10 - Black vertical
lines are visible
on the screen.
PROBLEMITEMS TO CHECKBefore calling your Authorized Product Support, please
check that the items below are properly connected or set.
In case of using a non-standard signal, please check the
pin assignments and the signal timing of your computer
with the specification outlined in Section 6. SPECIFICA-
TIONS.
LOCATION
No
pictureLED On
(Green)•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•Front (OSD)
Front
Rear
Rear
Computer
Press any...



- 1-11 -
ENGLISH
PROBLEMITEMS TO CHECK LOCATION
•
•
Two fine horizontal
lines are visible on
the screen.The 2 very faint thin lines across the screen are normal.
They are caused by the aperture grille stabilization
filaments(Damper Wires) which are required for all
aperture grille CRTs’.
A buzzing sound
when power on.A brief vibration or hum sound that is heard just after power
up is normal.  This is caused by the automatic degaussing
function.  This sound will be heard each time the monitor is...



- 1-12 -
Size 45cm/17(41cm/16 Diagonal Viewable Image)Mask type Aperture grilleGun In-lineDeflection angle 90°CRT Phosphors Red, Green, Blue EBU (medium short persistence)Aperture grille pitch 0.25mmFace Plate   Anti-glare, Anti-reflection and Anti-static filmFocusing method Dynamic Beam Forming (DBF)Video 0.7V analog RGBSync Separate H, V  sync., or Composite syncInput ConnectorsDB9-15PInput Impedance 75 Ω (video), 2.2k Ω(sync.)SCANNING Horizontal 31 - 96kHzFREQUENCY Vertical 55 - 160HzRESOLUTION...



- 1-13 -
ENGLISH
7.1 Optional Macintosh Adapter AD-A205 settings
The AD-A205 Macintosh Adapter(option) allows you to
take an advantage of the built in video capabilities of
your Macintosh computer with the monitor.
(1) Set the dip switches of the adapter, before connect
to the computer.
Apple Macintosh
Switch
ONSwitch Setting
2,4
Macintosh LC, LC II
Macintosh LC III, LC475, LC6301,2
Macintosh Quadra 610, 650, 700, 800, 840AV, 900, 950Macintosh Centris 610, 650, 660AV
Power Macintosh 4400, G3...



- 1-14 - (3)“AD-A205 Mac Adapter Setting Chart” shows all available modes for Macintosh systems and all possible combinations
with the monitor.
We recommend that you use the monitor with a preset timing. (See Section 1.2 Internal Preset Memory Capability)
(4) Please refer to the instruction book of your computer about the resolution setting.
Resolution may not be changed on some computers.
1. The resolution does not change with the computer powered on when you set the dip switches.
Be sure to power...



	



	
	


	

































	
	

	
	
	
 	
!		
 #
$	
 %
&
  
( )
*	
 +

&,-+
*	
 ./
0%!012&340240

 	



5555	


		
	

,
	

+
!		
626
 




•	

			
•   		
 		
 	  
	  	  
  		
 	    
 
 

		
• 



	

•!	

	!#

	

		
$!
%&$()&*+%!(,!
-	.(!#/((
01(	%()##/2*!/2#/3,...

0 
1!#!$2&#-/2#$((4
+1 &5$(25!/3!#

&		&
*+&	+


 


 6%%3$#&()&3 25*-/2#,
71
$&*#/%,%3$#&()&3 25*-/2#,


&
*	+
	
&




&
*	+