Mitsubishi Electric Ldt322v Users Manual

1. Determine the installation location
CAUTION:
DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY 
YOURSELF.
Installing your LCD display must be done by a qualifi ed
technician. Contact your dealer for more information.
CAUTION:
MOVING OR INSTALLING THE LCD MONITOR MUST BE 
DONE BY TWO OR MORE PEOPLE.
Failure to follow this caution may result in injury if the LCD
monitor falls.
CAUTION:
Do not mount or operate the display upside down, face up, or 
face down.
CAUTION:
Do not install the LCD monitor where it...

English
7. Adjust the sound
Make adjustments when adjustment of the volume is required.
8. Adjust the screen (See pages 23-31)
Make adjustments when adjustment of the screen display 
position or distortion is required.
9. Adjust the image (See page 23-31)
Make adjustments when adjustment such as the brightness 
or contrast is required.
10. Recommended Adjustment
To reduce the risk of “image persistence”, please adjust 
the following items based on the application being used.
“POWER SAVE” (See page 26),...

13. When LDT322V is installed in portrait position
Conditions
LDT322V can be installed in portrait position, under the following condi\
tions:
Caution:
Portrait position is effective only when wall-mounted or ceiling-mounted.
The stands(legs) can not be fi tted to the monitor in portrait position.
Placing the monitor in portrait position will shorten the average life o\
f the LCD backlight.
Operational Environment (Temperature) shall be limited, as shown below:
  Operational    Temperature    5 - 35 °C /...

English
1. Lay the screen face down
Lay the protective sheet on a table, which was wrapped 
around the monitor when it was packaged, beneath the 
screen surface so as not to scratch the screen face.
This device cannot be used or installed without the Tabletop 
Stand or other mounting accessory. Failure to follow correct 
mounting procedures could result in damage to the equip-
ment or injury to the user or installer. Product warranty does 
not cover damage caused by improper installation.
Failure to...

Connections
Before making connections:
*  First turn off the power of all the attached equipment and make connections.
*  Refer to the user manual included with each separate piece of equipment.\
Wiring Diagram
LCD monitorDVD player
HD or laser disk player Equipment with
digital interfacePersonal computer
Personal computer LCD monitor (second monitor)VCR

1-15  

English
Connecting a Personal Computer
Connecting your computer to your LCD monitor will enable you to display \
your computers screen image.
Some video cards may not display an image correctly.
Connect the LCD Monitor to a Personal Computer
•  To connect the RGB 2 IN connector (mini D-sub 15 pin) on the LCD monito\
r, use the supplied PC - Video RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin).
•  To connect the RGB 3 IN connector (BNC) on the LCD monitor, use a signal cable which is available...

Connecting with Digital Interface Equipment
Connections can be made with equipment that is equipped with a digital i\
nterface compliant with the DVI (Digital Visual 
Interface) standard.
Connect the LCD Monitor to a Computer with a Digital Output
•  The RGB 1 IN connector also accepts a DVI-D cable.
•  Input TMDS signals conforming to DVI standards.
•  To maintain display quality, use a cable with a quality prescribed by DVI standards. (See 29 page “DVI-MODE” )
•  The AUDIO IN 1, 2 and 3 can be used...

English
Connecting a DVD Player with component out
Connecting your DVD player to your LCD monitor will enable you to displa\
y DVD video.
Refer to your DVD player owner’s manual for more information.
Connect the LCD Monitor to a DVD Player
•   To connect the DVD/HD In connector (BNC) on the LCD monitor, use a separately available BNC connector cable.  You will need a BNC-to-RCA adapter to connect a DVD player with an RCA pin jack t\
o the BNC connector cable (not provided).
•   The AUDIO IN 2  and 3...

Connecting to a Stereo Amplifi er
You can connect your stereo amplifi  er to your LCD monitor. Refer to your amplifi  er owners manual for more information.
Connect the LCD Monitor to a Stereo Amplifi  er
•  Turn on the LCD monitor and the amplifi er only after all connections have been made.
•  Use an RCA cable to connect the AUDIO OUT connector (RCA) on the LCD m\
onitor and the audio input on the ampli fi er.
•  Do not reverse the audio left and right jacks.
•  The AUDIO IN 2 and 3 (both RCA) can be used...

English
1.  Pressing the Main Power Switch.
NOTE: 
When the Main Power Switch is used to power off the 
LCD monitor, the remote control and the power button will 
not  activate the on mode and both green and red power 
indicator turn off.  Be sure to turn the Main Power Switch 
to the on mode before using these two options.
2.  Pressing the power button.
NOTE: 
Before pressing the power button, be sure to turn on the 
Main Power button on the LCD monitor.
3.  Using the remote control.
NOTE: 
Before...