Mitsubishi Electric Ldt322v Users Manual

							
Power Indicator
Status
Power ON Green
Power OFF RedRed On
Green Blinking
Power Standby Red, GreenRed Blinking
*
Power Standby when 
“SCHEDULE” is enable
Diagnosis
(Detecting failure)
See troubleshooting on 
page 35
Using Power Management
The LCD monitor follows the VESA approved DPM Power
Management function.
The power management function is an energy saving
function that automatically reduces the power consumption
of the display when the keyboard or the mouse has not been
used for a fi xed period.
The power management feature on your new display has
been set to the “ON” mode. This allows your display to enter
a Power Saving Mode when no signal is applied. This could
potentially increase the life and decrease the power
consumption of the display.
Selecting a video source
To view a video source:
Use the input button to set [VIDEO].
Use the COLOR SYSTEM menu to set [AUTO], [NTSC],
[PAL], [SECAM], [PAL60], [4.43NTSC], according to your
video format.
Picture Size
RGB 1, 2, 3
DVD/HD, VIDEO FULL NORMAL DYNAMIC CUSTOM
REAL
FULL NORMAL CUSTOM
REAL
Signal Type
NORMAL
DYNAMIC FULL
4:3
Squeeze NORMAL SIZE Recommended Size
NORMAL: 
Display by the inputed signal aspect ratio by PC 
signal, or display in 4:3 aspect ratio at DVD/HD or VIDEO 
signal.
FULL:  Display in entire screen.
DYNAMIC:   Expand 4:3 pictures to the entire screen with 
non-linearity. (Some round image will be cut by expansion.)
CUSTOM (ZOOM):  Image can be expanded beyond the 
active display area. The image which is outside of active dis-
play area is not displayed.
REAL:  Image will be displayed 1 by 1 pixel.
 
ZOOM
ZOOM
Picture Mode
HIGHBRIGHTSTANDARDsRGB
HIGHBRIGHT STANDARD
CINEMA
RGB 1, 2, 3
DVD/HD, 
VIDEO
Audio Source Switching
You can switch the audio source using the AUDIO INPUT but-
ton. 
AUDIO1 AUDIO2 AUDIO3

1-21  
						

							
English
Information OSD
RGB1, 2, 3
Video Input mode
Input signal Information
Audio input mode
Picture Size modeRGB2 
1024 x 768 
48kHz  60Hz
AUDIO : 1 
SIZE : FULL
)
DVD/HD
Video Input mode
Audio input mode
Picture Size modeDVD/HD
AUDIO : 3 
SIZE : FULL
VIDEO, VIDEO
Video Input mode
Input Signal Colour System mode
Audio input mode
Picture Size mode
VIDEO
NTSC
AUDIO : 3
SIZE : NORMAL
PIP or POP
Main:RGB2
Sub:VIDEO
Main picture Information
Sub picture Information
Main picture Information
RGB2 
1024 x 768 
48kHz  60Hz
AUDIO : 1 
VIDEO 
NTSC 
SIZE : FULL
)

1-22  
						

							
OSD (On-Screen-Display) Controls 
SET
Press MENU button to 
open Main menu.  Press 
UP or DOWN button to 
select sub-menu.
Press EXIT button to 
open Main menu.
Press UP or DOWN 
button to select.UP or DOWN button INPUT button Press UP or DOWN, and 
PLUS or MINUS button to 
select function, or control 
which you like.  Press INPUT 
button to decide.
Press INPUT button to 
decide.
Press EXIT button 
to exit.Press UP or DOWN, and PLUS or 
MINUS button to select  function, 
or control which you like.
Press SET button to decide.
Remote Control
Control Panel
OSD screen
INPUT EXIT
“-” “+” button EXIT buttonPress MENU or 
EXIT button to exit.
Press SET button 
to decide.

1-23  
						

							
English
BRIGHTNESS
Adjusts the overall image and background screen brightness.
Press + button to increase brightness.
Press - button to decrease brightness.
CONTRAST
Adjusts the image brightness in relation to the input signal.
Press + button to increase contrast.
Press - button to decrease contrast.
NOTE: sRGB picture mode is standard and cannot be changed.
SHARPNESS
This function is digitally capable to keep crisp image at any timings.  \
It is adjustable to get a distinct image or a soft one as you prefer and set independently for each picture mode.
Press + button to increase sharpness.
Press - button to decrease sharpness.
BLACK LEVEL
Adjusts the image brightness in relation to the background.
Press + button to increase black level.
Press - button to decrease black level.
NOTE: sRGB picture mode is standard and cannot be changed.
NOISE REDUCTION     * : INPUT VIDEO, VIDEO only
Adjusts the noise reduction level.
Press + button to increase reduction level.
Press - button to decrease reduction level.
TINT     * : INPUT DVD/HD, VIDEO, VIDEO only
Adjust the tint of the screen.
Press + button the flesh tone color becomes greenish.
Press - button the flesh tone color becomes purplish.
COLOR     * : INPUT DVD/HD, VIDEO, VIDEO only
Adjust the color of the screen.
Press + button to increase color depth.
Press - button to decrease color depth.
COLOR TEMPERATURE
Color temperature can be selected out of 5000K, 6500K and 9300K.
When USER is selected, R.G.B can be adjusted individually. (RGB 1,2,3 only) 
COLOR CONTROL     * : INPUT RGB1,2,3 only
R, G, B: Increases or decreases Red, Green, and Blue depending upon which is selected.
The change in color will appear on screen and the direction (increase or decrease) will be shown by the color bars.
NOTE: It can be adjusted only when USER is selected by COLOR TEMPERATURE.
PICTURE RESET
Selecting Picture reset allows you to reset all OSD settings about PICTURE setting.
Select “Yes” and press “SET” button to restore to factory preset data.
Press “EXIT” button to cancel and then return to the previous menu.
PICTURE
Main-Menu

1-24  
						

							
H POSITION
Controls Horizontal Image position within the display area of the LCD.
Press + button to move screen to right.
Press - button to move screen to left.
V POSITION
Controls Vertical Image position within the display area of the LCD.
Press + button to move screen to UP.
Press - button to move screen to DOWN.
CLOCK     * : INPUT RGB2,3 only
Press + button to expand the width of the image on the screen the right.
Press - button to narrow the width of the image on the screen the left.
CLOCK PHASE     * : INPUT RGB2,3 only
Improves focus, clarity and image stability by increasing or decreasing this setting.
ZOOM MODE
You can select “FULL”, “NORMAL” and “CUSTOM” and “RE\
AL”. (INPUT RGB1/2/3 only)  You can also select “FULL”, 
“NORMAL” “DYNAMIC” and “CUSTOM” and “REAL”. (IN\
PUT DVD/HD, VIDEO, VIDEO only)
Selecting “DYNAMIC” will make the screen display panoramic with the expansion of the middle and outside of th\
e screen 
changed. (The upper and the bottom of the image will be cut by expansio\
n.)
Dynamic image is the same as FULL size image when HDTV signal is input.
Selecting “REAL” image will be displayed 1 by 1 pixel.
CUSTOM ZOOM
“CUSTOM ZOOM” will be selected when you select “CUSTOM” on t\
he screen “ZOOM” mode.
ZOOM: expands the horizontal and the vertical size simultaneously.
HZOOM:  expands the horizontal size only.
VZOOM:   expands the vertical size only.
H POSITION: moves to the right with + button. moves to the left with –\
 button.
V POSITION: moves up with + button. moves down with – button.
H RESOLUTION     * : INPUT RGB1,2,3 only
Adjusts the horizontal size by increasing or decreasing the setting.
Press + button to expand the width of the image on the screen.
Press - button to narrow the width of the image on the screen.
V RESOLUTION     * : INPUT RGB1,2,3 only
Adjusts the vertical size by increasing or decreasing the setting.
Press + button to expand the height of the image on the screen.
Press - button to narrow the height of the image on the screen.
SCREEN RESET
Selecting Screen reset allows you to reset all OSD settings from PICTURE setting.
Select “Yes” and press “SET” button to restore the factory preset data.
Press “EXIT” button to cancel and then return to the previous menu.
SCREEN
Main-Menu

1-25  
						

							
English
BALANCE
Adjust the balance of L/R volume.
Press + button to move the stereo sound image to right.
Sound of the left side will be small.
Press - button to move the stereo sound image to left.
TREBLE
To accentuate or reduce the high frequency sound.
Press + button to increase TREBLE sound.
Press - button to decrease TREBLE sound.
BASS
To accentuate or reduce the low frequency sound.
Press + button to increase BASS sound.
Press - button to decrease BASS sound.
AUDIO RESET
Selecting Audio reset allows you to reset all OSD settings from AUDIO setting.
Select “YES” and press “SET” button to restore the factory preset.
Press “EXIT” button to cancel and then return to the previous menu.
AUDIO
Main-Menu
PIP SIZE
Selecting the size of picture inserted at the “Picture-in-Picture” (PIP) mode.
“Large”, “Middle” and “Small” are available.
PIP AUDIO
Selecting the sound source in PIP mode.
When selecting “MAIN AUDIO”, you will get the sound for the main p\
icture and when selecting “PIP AUDIO”, 
you will get the sound for the picture instead.
PIP RESET
Selecting PIP Reset allows you to reset all OSD settings from PIP setting.
Select “Yes” and press “SET” button to restore the factory preset data.
Press “EXIT” button to cancel and then return to the previous menu.
PIP (PICTURE IN PICTURE)
Note: The “PIP” and “POP” modes do not function when the scr\
een size is “CUSTOM” or “REAL”.
Main-Menu

1-26  
						

							
AUTO SETUP     * : INPUT RGB2,3 only
Press SET button to automatically adjust screen size, horizontal position, vertical position, clock, clock phase, 
white level and black level.
Press EXIT button to cancel execution AUTO SETUP and then will return to the previous menu.
AUTO ADJUST     * : INPUT RGB2,3 only
Selecting the auto adjust ON/OFF.
Selecting ON when changing the timing, the horizontal position, vertical\
 position and clock-phase will adjust automatically.
POWER SAVE
Selecting RGB ON, the monitor will go to power management mode when RG\
B1,2,3 sync is lost.  
Selecting VIDEO ON, the monitor will go to power management mode after\
 about 10 minutes delay from when DVD/HD 
and VIDEO input signal is lost.
LANGUAGE
OSD control menus are available in seven languages. 
(English, German, Spanish, French, Italian, Swedish and Japanese)
SCREEN SAVER
Select SCREEN SAVER functions to reduce the risk of the image persistence.
GAMMA: The display gamma is changed and fixed when selected ON.
COOLING FAN: The built in cooling fan is always on when set ON.
BRIGHTNESS: The brightness is decreased when selected ON.
MOTION: Image is slightly expanded and moves 4 directions (UP, DOWN, RIGHT, LEFT) periodically 
(Need setting the time for movement).
Movement area is approximately +/- 10mm from original position; 
Please locate the important information such as text within 90% area of screen image.
See note (1) for this functions.
PIP and STILL will be disabled when MOTION is active.
COLOR SYSTEM     * : INPUT VIDEO, VIDEO only
Selecting the Color System depends on your input video format.
AUTO: NTSC, PAL, SECAM, PAL60 or 4.43 NTSC is automatically selected.
NTSC: Specific selection of NTSC.
PAL: Specific selection of PAL.
SECAM: Specific selection of SECAM.
PAL-60: Specific selection of PAL60.
4.43NTSC: Specific selection of 4.43 NTSC.
SIDE BORDER COLOR
Selecting the side black bar color white when 4:3 image displayed, you c\
an select OFF, 50 and 100. 
CONFIGURATION RESET
Selecting the CONFIGURATION RESET allows you to reset all configuration settings.
Select Yes and press SET button to restore the factory preset data.
Press EXIT button to cancel and return the previous menu.
FACTORY RESET
Selecting YES allows you to reset PICTURE, SCREEN, AUDIO, CONFIGURATION1,2 and ADVANCED OPTION will be 
back to factory settings (except LANGUAGE, DATE AND TIME and SCHEDULE).  
Select YES and press SET button to restore the factory preset data.  Press EXIT button to cancel and return the 
previous menu.
CONFIGURATION 1
Main-Menu

1-27  
						

							
English
OSD TURN OFF
The OSD control menu will stay on as long as it is use.  In the OSD Turn Off submenu, you can select how long the monitor 
waits after the last touch of a button to shut off the OSD control menu. 
The preset choices are 5 -120 seconds.
INFORMATION OSD
Selects the information OSD display or not. 
The information OSD will display when input signal or source change or warning message like as no-signal or out-of range.
A time between 1 to 10 seconds is available.
OFF TIMER
To select OFF TIMER mode ON/OFF.
In the OFF TIMER menu, you can preset the monitor to automatically power down.
A time between 1 to 24 hours is available.
When the OFF TIMER is set, the SCHEDULE (see page 29) settings will be\
 disabled.
OSD H POSITION
Adjusts the horizontal position of the OSD menu.
OSD V POSITION
Adjusts the vertical position of the OSD menu.
MONITOR INFORMATION
Indicates the model and serial number of your monitor.
CONFIGURATION 2
Main-Menu

1-28  
						

							
INPUT RESOLUTION     * : INPUT RGB2,3 only
Selects to decision of input signal about below timings, 1024x768, 1280x\
768 and 1360x768.
AUTO: Determines the resolution automatically.
1024x768: Determines the resolution as 1024x768
1280x768: Determines the resolution as 1280x768
1360x768: Determines the resolution as 1360x768
BLACK LEVEL EXPANSION     * : INPUT VIDEO, VIDEO only
Selects a level of black expansion.
In case of go under the black cut-off level, please adjust the “Black level” in moderation on OSD menu\
.
GAMMA SELECTION
Selects a display gamma.
2.2
2.4
S gamma
Native
NOTE: sRGB picture mode is standard and cannot be changed.
SCAN MODE     * : INPUT DVD/HD, VIDEO, VIDEO only
Changes the display area of the image.
OVERSCAN: Set to display area about 95%
UNDERSCAN: Set to display area about 100%
SCAN CONVERSION     * : INPUT DVD/HD, VIDEO, VIDEO only
Selects IP (Interlace to Progressive) converter function.  
PROGRESSIVE: Enable the IP function, to convert interlace signal to progressive. Normally use this setting.
INTERLACE*: Disable the IP function.
*NOTE: This mode is better suited for motion pictures, but it increases chance of image retention.
FILM MODE     * : INPUT DVD/HD, VIDEO, VIDEO only
Selects Film mode function.
AUTO: Enable the Film mode function. This mode is better suited for movi\
es, which is converted 24 Frames/sec source 
to DVD Video. We recommend to select “PROGRESSIVE” in “SCAN CONVERSION”.
OFF: Disable the Film mode function. This mode is better suited for Broadcasting or VCR source.
IR CONTROL
Selects the infrared wireless remote controller mode. 
The item in this menu will become effective by pressing “SET” button on the selected item.
NORMAL: The monitor will be controlled normally by wireless remote controller.
LOCK: Disable the monitor control by infrared wireless remote controller.
Keep pressing “DISPLAY” button during 5 sec or more, this setting will return to “NORMAL”.
ADVANCED OPTION
Main-Menu

1-29  
						

							
English
TILING
TILING demonstrates multiple screens. This feature provides a single lar\
ge screen using up to 16 monitors.  
It will be able to divide up to 4 each H and V.  
This requires you to feed the PC output into each of the monitors throug\
h a distributor.
H MONITORS: Select number of horizontal divide.
V MONITORS: Select number of vertical divide.
POSITION: Select a position to expand the screen.
FRAME COMP: Works in tandem with TILING to compensate for the width of t\
he tile bezels in order to accurately 
display the image.
ENABLE: Select “YES”, the monitor will expand the selected positio\
n. 
PIP and STILL will be disabled when “TILING” is activated.
HEAT STATUS
Information of status for COOLING FAN, BRIGHTNESS and TEMPERATURE.
COOLING FAN comes to run when inside temperature is over a guaranteed li\
mit.
In this case warning is displayed on the screen.
POWER ON DELAY
Adjusts the delay time from “standby” to “power on” mode.
“POWER ON DELAY” time is selectable from OFF, 2sec, 4sec, 6sec, 8s\
ec, 10sec, 20sec, 30sec, 40sec and 50sec.
DATE AND TIME
Adjusts the current date and time for internal clock.
You should set this function when you use “SCHEDULE”.
SCHEDULE
Programs the monitors working schedule.
Schedule the power on and power off with hour and a day of the week. Als\
o sets the input port.
This OSD cant remove except EXIT.
(see “NOTE 2” on page 30 for further information)
DVI-MODE     * : INPUT RGB1 only
Selects the kind of DVI-D equipment which is connected RGB1. 
Select “DVI-PC” when PC or other computer equipment is connected.
Select “DVI-HD” when DVD player, which has DVI-D output, is connec\
ted.
ADVANCED OPTION RESET
Selecting ADVANCED OPTION reset allows you to reset all OSD settings fro\
m ADVANCED OPTION settings, 
except for DATE AND TIME.
Select “YES” and press “SET” button to restore the factory p\
reset data.
Press “EXIT” button to cancel and then return the previous menu.

1-30