Mitsubishi Electric Lt 46164 Owners Guide

							 Appendices 81
For assistance call 1(800) 332-2119
If prompted for a name, 4. 
highlight a name for the 
device and press ENTER to 
add a check.  The device 
itself may later override the 
name assigned.
Highlight 5. On and press 
ENTER to add a check.
Highlight 7. EXIT and press ENTER to close the New 
Device Found screen.
Note:  At any time after completing Auto Input Sens-
ing, you can set the TV’s HDMI control on or off 
in the Inputs > HDMI Control menu.
265 Series.8.   To supplement HDMI control with 
NetCommand IR control, see page 60.
Many new HDMI devices have a feature called Con-
sumer Electronics Control (CEC) or HDMI Control.  
HDMI Control allows one device, such as the TV, to 
control other devices, such as an A /V receiver or disc 
player.  Use of CEC is optional.
Each manufacturer chooses which CEC functions to 
support so it is difficult to predict which devices and 
features are compatible with Mitsubishi’s HDMI Control.  
You may find that CEC functions for a specific device are 
limited.
To use HDMI Control, you must enable it in both 
the TV and the device.
In the TV.•	  Enable HDMI control from the New 
Device Found screen or from the Inputs > HDMI 
Control menu.
I•	n the Device.  Most devices with HDMI CEC com-
patibility let you turn it on or off in the device menus, 
where it is typically listed as “HDMI Control.”
Enabling HDMI Control of CEC Devices
To ensure proper detection
Power on HDMI devices before connecting them to •	
the TV.
Connect and set up HDMI devices one at a time.•	
Power on the device and allow it to complete the 1. 
power-on sequence (boot up).  Stop any playback.
Connect the device to one of the TV’s HDMI inputs.2. 
When the TV detects the connection, the 3. New 
Device Found screen will appear.
Note:  See “If the New Device Found Screen Has No 
HDMI Control Option” on this page if there is no 
HDMI Control option.
New Device Found screen with HDMI Control option.  
This screen displays only if the device’s HDMI Control is 
enabled.
Appendix C:  HDMI Control of CEC Devices
If the New Device Found Screen 
Has No HDMI Control Option
If the New Device Found screen shows no option for 
HDMI Control, one of these conditions applies:
HDMI Control is turned off in the menus of the •	
new device
Action:
Highlight a. EXIT and press ENTER to close the 
New Device Found screen.
Display the device’s setup menus and enable b. 
the device’s CEC capabilities.
Wait for the TV’s c. New Device Found screen 
to appear again.
If the d. New Device Found screen does not 
appear, power off the device.  Power on the 
device and wait for the New Device Found 
screen to display with the HDMI Control 
option.
The HDMI cable cannot support CEC•	
Action:
Upgrade your HDMI cable to one that supports 
CEC.
The device does not have CEC compatibility•	
Action:
Control the device with its own remote  -
control or program the TV’s remote control to 
operate the device.
265 Series. -  Use the TV’s NetCommand IR 
control (page 60).
 
						

							82 Appendices
For assistance call 1(800) 332-2119
HDMI Control of an HDMI A/V 
Receiver and Connected Devices
Note: Connect the A/V receiver to the TV with an 
HDMI cable before making other connections.
Enable HDMI Control for the A /V receiver as 1. 
described in “Enabling HDMI Control of CEC 
Devices” on the previous page.
Power on the HDMI device you wish to connect to 2. 
the A /V receiver (such as a disc player, cable box, 
or satellite receiver).  Allow the device to complete 
the power-on sequence (boot up).  Stop playback if 
the device starts playing.
Connect the device to the A /V receiver with an 3. 
HDMI cable.
Select the device’s HDMI input on the A /V receiv-4. 
er’s front panel controls or remote control.
When the TV detects the connection, the 5. New 
Device Found screen will appear.
Note:  If the TV is unable to detect the device, either 
the device’s CEC capability is not enabled or 
the device is not CEC compatible.  Enable 
HDMI control through the device’s menus 
before continuing.  You may need to temporar-
ily connect the device directly to the TV to view 
device menus.
Highlight 6. On and 
press ENTER to 
add a check.
Highlight 7. EXIT and press ENTER to close the New 
Device Found screen.
Optional:  Connect the TV’s 8. DIGITAL AUDIO 
OUTPUT to an input on the A /V receiver.  Use this 
additional connection if:
You want the ability to switch between the A /V •	
receiver speakers and the TV speakers.
You want to use the A /V receiver to listen to •	
devices connected to the TV only, e.g., an 
antenna input or camcorder.
265 Series.9.   If desired, perform NetCommand IR 
Learning to supplement CEC functions.  You must 
first connect and place IR emitters for the devices.  
See page 60.
HDMI OUTOPTICAL
AUDIO IN
High-denition 
DVD player
DVD player
Cable box
VCR
Y/ VIDE O
TV
A/V receiver with 
HDMI output
HDMI 
cables
Devices with HDMI 
output to A/V receiver
Optional  
digital audio  connectionHDMI cable
Connecting HDMI devices.  The optional digital audio 
connection allows you to hear audio through the A/V 
receiver from devices connected to the TV only.
Appendix C:  HDMI Control of CEC Devices, continued
    
						

							 Appendices 83
For assistance call 1(800) 332-2119
Using HDMI Control
As an example of using HDMI Control, press P L AY on 
the device itself to:
Power on the TV•	
Switch to the device (no need to display the •	
Input Selection menu)
Begin play of the device•	
Direct Keys
Test your equipment with the TV’s remote control to 
find additional supported commands.  See the table 
below for commands that may be available, depending 
on the individual device.
CEC-enabled VCR, DVD, and DVR functions that 
may be available:
Record/
Playback
Menu 
 Navigation
Channel 
TuningOther
     CHGUIDE
ENTERDigits 0–9, 
CANCEL
TOOLS
Check the 
TOOLS menu 
for supported 
functions.
CANCEL 
(to cancel)ENTER
If you have a CEC-enabled A /V receiver, CEC-enabled 
devices connected to the A /V receiver with an HDMI 
cable may also be controllable.  They can be selected 
from the TV’s Input Selection menu.
CEC-enabled A /V receiver functions that may be 
available:
Try the •	VOL, MUTE, and menu-navigation keys.
To open the A /V receiver menu, follow these steps:•	
While watching TV, press 1. AUDIO.
Press 2.  until the TV Speakers option displays.
Press 3.  to select Off (to send audio to the A /V 
receiver).
Press 4. INPUT and highlight the A /V receiver icon 
in the Input Selection menu.
Press 5. TOOLS.
Select 6. Menu from the Tools menu.
Resolving CEC Conflicts
Because each manufacturer selects which CEC func-
tions to support, some devices can conflict with other 
devices.  If control conflicts arise, you can:
Turn off TV control of an individual CEC-enabled •	
device (see below).
Turn off CEC in the setup menu of one of the •	
devices.
Turning Off the TV’s HDMI Control of a CEC Device
Press 1.  MENU on the TV remote control.
Highlight 2. Inputs > HDMI Control.
Move to the device name and press 3. ENTER to select 
Off to turn off the TV’s ability to control the device.
Press 4. EXIT to clear the menu.
Inputs > HDMI Control menu
Removing an HDMI Device
Power off the device.1. 
Disconnect the HDMI cable.2. 
Press 3. MENU on the TV remote control to enter the 
TV main menu.
Go to 4. Inputs > Name.
Highlight the HDMI input name and press 5. ENTER to 
select Delete.
Press 6. EXIT to clear the menus.
Inputs > Name menu with Delete selected for HDMI-3.
Appendix C:  HDMI Control of CEC Devices, continued
 
						

							84 Appendices
For assistance call 1(800) 332-2119
Cleaning Recommendations
Normally, light dusting with a dry, non-scratching duster 
will keep your TV clean.  If cleaning beyond this is 
needed, please use the following guidelines:
First, turn off the TV and unplug the power cord from 
the power outlet.
Occasionally clean dust build-up from the air-intake 
grilles on the back and sides of the TV.  Clean using a 
vacuum cleaner with a brush attachment.
Top and Sides of the TV 
Gently wipe down your TV with a soft, non-abrasive •	
cloth such as cotton flannel, microfiber, or a clean 
cloth diaper, lightly moistened with water.  Dry with 
a second dry, soft, non-abrasive cloth.
For oily dirt, add a few drops of mild liquid deter-•	
gent, such as dishwashing detergent, to the water 
used to moisten the cloth.  Rinse with a second 
cloth moistened only with water.  Dry with a third 
dry, soft, non-abrasive cloth.
Screen
I M P O R TA N T
DO NOT apply any type of liquid to the surface of 
the TV screen.
Use only a soft, dry cloth to clean the LCD •	
screen.  Do not use any liquids.
Wipe the screen gently with an up and down •	
motion.
Clean the entire screen evenly, not just sections of •	
the screen.
General Cleaning Precautions
DO NOT allow liquid to enter the TV through the •	
ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as •	
these can scratch the surfaces.
DO NOT use any cleaners containing ammonia, •	
bleach, alcohol, benzene, or thinners, as these can 
dull the surfaces.
DO NOT spray liquids or cleaners directly on the •	
TV’s surfaces.
DO NOT scrub or rub the TV harshly.  Wipe it gently.•	
Care of the Remote Control
Remote Control Tips
For longer life, use alkaline batteries.•	
Do not mix old and new batteries.•	
Be within 20 feet of the equipment.•	
Do not press two or more keys at the same time •	
unless instructed to do so.
Do not allow the unit to get wet or become heated.•	
Keep the unit out of direct sunlight.•	
Avoid dropping on hard surfaces.•	
Do not use harsh chemicals to clean.  Use only a •	
soft, lightly moistened cloth.
Resetting the Remote Control
If TV mode is selected and the TV does not respond 
properly, reset the remote control.
Press and hold 1. POWER for several seconds until the 
mode indicator blinks twice and goes off.
Release the 2. POWER key.
Press keys 3. 0   0   9   3   5 and the mode indicator will 
blink twice when you finish entering the code.  
When entering the code, pause for a moment 
between each key press to ensure it is recognized.
Low-Battery Indicator
If you press a key and the mode indicator blinks five 
times, replace the remote control’s batteries.
Appendix D:  TV Care
 
						

							 Appendices 85
For assistance call 1(800) 332-2119
Reset NameWhen to UseHow to UseResulting Action
FormatIf the picture shape 
(aspect ratio) seems 
incorrect, use the 
FORMAT key to change 
the shape of the 
picture.
Press FORMAT to cycle through the 
aspect ratios available for the signal.
The last-used format for a signal 
type is memorized for each input.  
The next time the same input and 
signal type are viewed, the last-
used format will be recalled.
PerfectColor™/ 
PerfecTint™ 
Reset (265 
Series)
(for the single 
input currently 
being watched)
When the color 
intensities seem out 
of balance, use the 
PerfectColor/PerfecTint 
reset to reset the color 
balances to the original 
factory settings.
Both PerfectColor and 
PerfecTint are reset at 
the same time.
While viewing the input to be 1. 
reset, press MENU and go to 
Picture > Perfect.
Press 2. ENTER to display the 
PerfectColor adjustment screen.
Press 3. CANCEL to reset the colors.
All PerfectColor/PerfecTint 
sliders are reset to the original 
center position.  The PefectColor/
PerfecTint settings for other 
inputs remain unchanged.
A /V Memory 
Reset
(for the single 
current input)
When audio and/
or video settings for 
a single input seem 
incorrect, use A /V 
Memory Reset to 
return the input to 
the original factory 
settings.
During General TV Viewing
While viewing the input to reset, 1. 
press MENU and go to Picture > 
Reset.
Press 2. ENTER to highlight Reset.
Press 3. ENTER again to reset.
While Using VUDU Movies and 
Some VUDU Apps
Press TOOLS and 3.
All Audio and Video settings for 
the individual input are reset 
except for the global settings 
for audio Balance, Listen To, 
Language, True 120 Hz/True 240 
Hz, and settings in the Picture > 
Advanced menu.
TV Reset Comparison Guide
You can resolve many common TV problems using 
the reset functions described in the following table.  
See also the troubleshooting suggestions later in this 
appendix.
I M P O R TA N T
Before you change sound or picture settings:  If 
picture or sound settings seem wrong for a broadcast 
channel (a channel from the ANT input, a cable box, or 
satellite receiver), first check other channels from the 
same input before changing settings.  If most other 
channels from the same input seem correct, there is 
likely a problem with the broadcast rather than with the 
TV.  Use care in this case, as changes you make to fix 
problems on individual channels also affect all other 
channels on the same input.
Appendix E:  Troubleshooting
Service and Customer Support
Service
If you are unable to correct a problem with your TV, 
consult your Mitsubishi dealer or Mitsubishi Con-
sumer Relations at (800) 332-2119.
•	 DO	NOT	adjust	any	controls	other	than	those	
described in this Owner’s Guide.
•	 DO	NOT	remove	the	protective	back	cover	of	
your TV.
Customer Support
•	 To	order	replacement	or	additional	remote	con-
trols, visit our website at www.mitsuparts.com or 
call (800) 553-7278.
•	 For	questions:
 Call Consumer Relations at 800-332-2119.
 E-mail:  [email protected]
 Website:  www.mitsubishi-tv.com
 
						

							86 Appendices
For assistance call 1(800) 332-2119
Reset NameWhen to UseHow to UseResulting Action
A /V Reset
(for all inputs)
To reset audio and 
video adjustments for 
all inputs to the original 
factory settings.
While viewing the TV, press the 
control-panel buttons INPUT and 
VOLUME DOWN at the same time for at 
least two seconds.
All Audio and Video settings are 
returned to the original factory 
settings, including global settings 
not affected by Picture > Reset.
Channel 
Memorization
To erase and 
re-memorize channels 
on the ANT input.
While viewing the TV, press 1. 
MENU to display the main menu.
Navigate to the 2. Setup > 
Channel menu.
Highlight the reception mode, 3. 
e.g. Ant Air.
Select 4. All channels.
Highlight 5. Scan.
Press 6. ENTER to start channel 
memorization.
All previously memorized chan-
nels for the antenna input are 
erased and a new set of memo-
rized channels is created.  To 
add or delete individual channels, 
see the Setup > Channel > Edit 
menu instructions on page 53. 
Lock Menu 
Pass Code
To change your Lock 
menu pass code
See the cutout page from Appendix B, 
page 79.
Allows establishment of a new 
code.
Control-Panel 
Lock Release
To re-enable the 
control-panel buttons 
after activation of the 
Control-Panel Lock
Press and hold the INPUT button on 
the control panel for ten seconds.  If 
the TV is powered off, you can then 
press the POWER button to turn it on.
Allows the control panel to be 
unlocked if the remote control is 
misplaced.
Auto Input 
Sensing for 
HDMI
If the New Device 
Found screen does 
not appear when you 
connect an HDMI 
device.
Disconnect the HDMI device.1. 
Delete the HDMI input in the 2. 
Inputs > Name menu (see page 
55).
Power on and connect the new 3. 
device.
The New Device Found screen 
will display.
System ResetIf the TV does not turn 
on or off, does not 
respond to the remote 
control or control-
panel buttons, or has 
audio but no video.
Press and hold the POWER button on 
the control panel for ten seconds.
The TV will turn off.  Power on the 
TV and the green LED will flash 
quickly for about one minute.  The 
changes you made most recently, 
before using SYSTEM RESET, may 
be lost.
TV Reset
I M P O R TA N T:  
Use this reset 
only if other 
troubleshooting 
has been unsuc-
cessful.
To reset all consumer-
accessible settings 
and all memories to 
the original factory 
defaults.
Use TV Reset if the TV 
can respond to con-
trols but TV behavior is 
abnormal.
CAUTION:  All owner-
performed setups and 
adjustments will be 
erased.
While viewing the TV, press 1. 
MENU to display the TV main 
menu.
With the main menu displayed, 2. 
press number keys 1  2  3 to 
display the Reset menu.
READ THE ON-SCREEN 3. 
WARNING AND INSTRUC-
TIONS.
If you do not wish to use this •	
reset, press EXIT or MENU to 
back out.
If you do wish to use the •	
reset, press ENTER to erase 
all memories and settings.
The TV will start the initialization 
process and then turn off.  
Power on the TV and the front 
green LED will start flashing.  All 
memory and settings outlined in 
this Owner’s Guide will need to 
be set again.
Appendix E:  Troubleshooting, continued
 
						

							 Appendices 87
For assistance call 1(800) 332-2119
Appendix E:  Troubleshooting, continued
General TV Operation
SymptomRemarks
 1.The TV remote control does not work.Check that the batteries are fresh and installed correctly.•	
Check that the control mode on the remote is set to TV.•	
Be no more than 20 feet from the TV when using the remote control.•	
Program the remote control to operate the TV or other device.•	
Reset the remote control.  See •	“Resetting the Remote Control,”  
page 84.
 2.When I try to use the remote control, the POWER 
key blinks five times.
Replace the batteries.
 3.TV does not respond to the remote control or 
to control-panel buttons and TV will not power 
on or off.
Unplug the AC power cord for 10 seconds.•	
Press and hold the •	POWER button on the control panel to 
perform system reset.
 4.When a device is selected from the Input 
Selection menu, the screen is blue or black (no 
signal source).
•	 Make	sure	the	selected	device	is	turned	on.
•	 Begin	play	of	the	device.
 5.You have forgotten your Lock menu pass code.See “Bypassing the Parental Lock”, Appendix B.
 6.Rating restrictions are not working.Open the Lock > Parental menu and:
•	 Verify	that	the	ratings	locks	are	active.
•	 Check	the	Lock	Time/Unlock	Time	to	check	if	rating	restric-
tions are disabled.
•	 Rating	restrictions	apply	only	to	content	on	the	ANT	input.
 7.On-screen displays appear each time you 
change a function.
Normal TV operation.
 8.A warning message appeared on screen 
stating, “TV will shut down in a few seconds.  
Please check if the air flow is blocked.”
•	 Internal	TV		temperature	has	exceeded	proper	levels.		Cool	
the room.
•	 The	TV	has	overheated.		Clear	blocked	air	vents	and	ensure	
at least four inches of clearance on all sides of the TV.
 9.I have turned on CEC for my HDMI devices but 
control is erratic and I wish to disable it.
First •	turn off the TV’s HDMI control for the specific device.  
Open the Inputs > HDMI Control menu, select the device, 
select Off.
Disable CEC on the device itself.  See the device’s instruc-•	
tions.
If the problem persists, do the following:•	
Disconnect the device from the TV.1. 
Open the 2. Inputs > Name menu and select Delete for 
the device.
Reconnect the device to the TV and Auto Input Sensing 3. 
will recognize the device with CEC disabled.
Reset NameWhen to UseHow to UseResulting Action
VUDU
Reset VUDU 
Account Pass-
word
You have forgotten 
your account pass-
word.
Using a computer, go to 
www.VUDU.com.
Reset your account password 
from the VUDU website (requires 
access to e-mail).
VUDU
Reset Parental 
Controls Pass 
Code
You have forgotten 
your pass code.
Call VUDU Customer Care at 
1-888-554-VUDU (8838).
VUDU Customer Care will reset 
your pass code.
 
						

							88 Appendices
For assistance call 1(800) 332-2119
Appendix E:  Troubleshooting, continued
TV Channels
SymptomRemarks
 1.The TV takes several seconds to respond to 
channel changes.
It is normal for digital channels to take longer to tune in.•	
Press •	ENTER after entering a channel number to minimize 
delays.
Use a 4-digit number for an over-the-air digital channel.•	
Use a 6-digit number for digital cable channels if your cable •	
service is able to recognize 6-digit channel numbers.
 2.You cannot access a channel.Use number keys instead of •	CH.
Be sure the channel you want to view is in memory.•	
Check that the TV is switched to the correct device or •	
antenna for that channel by pressing the INPUT key.
Make sure the •	Lock > Parental menu lock is set to Off.
If you cannot tune to a virtual digital channel even though the •	
TV has already memorized digital channels, tune to the physi-
cal channel number used by the broadcaster.  The virtual 
channel will then be automatically added to memory.
You may be trying to tune to an analog channel that is no •	
longer broadcasting.
 3.When ChannelView list is displayed, informa-
tion appears incomplete
Press •	INFO to update the display for the highlighted channel.
Program information is displayed only for the currently tuned •	
channel.
Available information is sent from the broadcaster or cable •	
provider.  No other data is available.
Make sure the TV clock is set correctly.•	
TV Power On/Off
SymptomRemarks
 1.TV takes an excessively long time to power 
on.
When powered on, the TV needs time to boot up, just as a com-
puter does.
 2.You cannot program the TV to turn on auto-
matically (Timer function)
The TV may be locked.•	
The clock may not be set.•	
 3.TV turned itself off and the light on the front 
panel started to blink.
Momentary power fluctuation can cause the TV to turn off •	
to prevent damage.  Wait for the green light to stop flashing 
and turn the TV on again.
 If the TV does not stay on, press the •	POWER button on the 
control panel for at least eight seconds to perform System 
Reset.  If this happens frequently, obtain an AC line power 
conditioner/surge protector.
An unusual digital signal may have been received, triggering a •	
protection circuit.  Wait for the light to stop flashing and turn TV 
on.
 4.TV will not power off.Press the POWER button on the control panel for ten seconds to 
perform System Reset.
 
						

							 Appendices 89
For assistance call 1(800) 332-2119
Appendix E:  Troubleshooting, continued
Picture
SymptomRemarks
 1.Picture does not look like a high-definition 
picture.
Not all signals are high-definition signals.  To receive high-defini-
tion programming from your cable or satellite provider, you must 
subscribe to the provider’s high-definition service.   Some over-
the-air broadcasts are in high-definition and can be received with 
a high-quality antenna suited to your location.
 2.TV has sound but no picture.Press •	MENU on the remote control.  If the menu displays, 
then there is a problem with the incoming signal.
Check that all video inputs are plugged in firmly.•	
Press and hold the •	POWER button on the control panel for ten 
seconds to perform System Reset.
 3.You cannot view a picture when playing a 
VHS tape.
Check your VCR’s owner’s guide for further troubleshooting. 
 4.VCR or DVD player’s on-screen menus jitter 
up and down.
Stop playback.  Possible cause:  Many VCRs and DVD players 
provide on-screen menus at only half-resolution that may 
appear to jitter up and down.
 5.When viewing a stopped VCR, white lines 
are rolling on the screen.
•	 Turn	off	video	mute	for	the	VCR.
•	 Begin	playing	the	tape.
•	 Change	the	VCR	input	from	Line	1	to	the	VCR	antenna	input.
 6.A color program appears as a black and 
white image, or the colors are dim, or the 
screen is black.
The PerfectColor color balance has been incorrectly set.  Reset 
the PerfectColor balance.
 7.Picture from an HDMI input is noisy (poor 
quality).
Upgrade a standard (unmarked) HDMI cable to a high-speed 
HDMI cable.
 8.The image from a computer appears dis-
torted when viewed on the TV.
Normal TV operation.  The TV does not correct distortion in •	
the picture from a computer because the correction process 
may cut off the edges of the image.
The aspect ratio may be wrong for the image.  Press •	FORMAT 
to change.
 
						

							90 Appendices
For assistance call 1(800) 332-2119
Appendix E:  Troubleshooting, continued
Sound 
SymptomRemarks
 1.There is no sound even when the 
volume is turned up.
•	 Check	if	the	MUTE key is on.
•	 The	TV’s	analog	Listen to setting may be set to SAP (analog 
program from the ANT input) but no SAP is being broadcast.
•	 Check	that	the		Sound > Audio > TV Speakers option is set to On 
to hear sound from the TV speakers.  Possibly the TV Speakers 
option is Off or set to Center but there is no A /V receiver con-
nected.
•	 If	using	an	A /V	receiver,	check	that	the	Sound > Audio > TV 
Speakers option is set to Off to hear sound from the A /V receiver 
speakers.
•	Press and hold the POWER button on the control panel for 10 
seconds to perform System Reset.
• The language selected in the Setup > Antenna Digital Audio 
menu is not being broadcast for the current program.
 2.The sound does not match the screen 
picture.
The TV’s analog Listen to setting may be set to SAP (analog program 
from the ANT input).
 3.The sound from my A /V receiver does 
not match the screen picture (I should 
hear the correct audio from my A /V 
receiver).
Check that •	DIGITAL AUDIO OUTPUT and/or AVR/SURROUND 
OUTPUT on TV’s connection panel is connected to the A /V 
r e c e i v e r.
Without this connection, devices connected only to the TV (and 
not the A /V receiver) can be heard only from the TV speakers.  
Note that this includes the ANT input, a device (such as a 
camcorder) connected to the TV, and any other device sending 
audio to the TV only.
If using a NetCommand-controlled A /V receiver, NetCommand •	
may be selecting the wrong A /V receiver audio input.  Check the 
A /V receiver’s NetCommand setup in the Inputs > AVR menu.
 4.Cannot select an audio-only device; it 
does not appear in the Input Selection 
menu.
Plug an unused video plug into the Y/ V I D E O jack to activate Auto 
Input Sensing.  Assign the name C D/Au d i o or MP3 to make the 
audio device selectable in the Input Selection menu.
.5.Sound is coming from the TV speakers 
instead of the A /V receiver.
Connect the TV’s •	AUDIO OUT to the A /V receiver.
Change TV Speakers setting to •	Off or Center.