Mitsubishi Electronics Projector HC100 User Manual
Have a look at the manual Mitsubishi Electronics Projector HC100 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 20 Mitsubishi Electronics manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
EN-31 ENGLISH POWER Off Steady red Blinking red / green STATUS Off Off Blinking orange Blinking green Steady red Off Steady or Blinking Solution •Connect the power cord to the projector. •Plug the power cord into a wall outlet. •If any objects are blocking the air inlet or outlet grille, remove them and carry out the following. 1. Unplug the power cord from the wall outlet. 2. Make sure that the projector has cooled off. 3. Plug the power cord into the wall outlet. 4. Press the POWER button. •If any objects are blocking the air inlet or outlet grille, remove them. •Dont expose the air outlet grilles to hot air emitted from a heating appliance. •After the STATUS indicator stops blinking, press the POWER button. •If you unplug the power cord while the fan is rotating, the lamp may not turn on about one minute when you plug the power cord next time. •The lamp cant turn on again for one minute after it goes out. •Press the POWER button several times. •Replace the lamp. (The lamp is at the end of its life.) •Attach the lamp cover on the bottom. •Unplug the power cord from the wall outlet and contact your dealer. Troubleshooting Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to unplug the power plug, and then contact your dealer. No image appears on the screen. Problem Power can not be turned on. No image appears on the screen. Projected images suddenly disappear.Solution •Check whether the indicators are on or off and how they are lightning. •Check that the lens cap is removed. •It may take about one minute for the lamp to light up. •The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again. •If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the power cord is plugged. After the fan stops rotating, press the POWER button to turn back on the POWER indicator. •Check that the intake vent is clean. •Check that the lamp cover is closed. (See Page 29.) •Check that the cables connected to the external devices are not broken. •When an extension cable is being used, replace it with the supplied cable for check. When images are displayed correctly, add an RGB signal amplifier to the extension cable. •This problem may occur when the intake vent and/or exhaust vents are blocked. (In such a case, the STATUS indicator brink orange.) ➔Remove the objects blocking the intake vent and/or exhaust vents and then carry out the following procedure. 1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator goes out.) 2. Unplug the power cord from the wall outlet. 3. Wait about 10 minutes. 4. Plug the power cord into the wall outlet. 5. Press the POWER button. •When the STATUS indicator is steady red, it is indicating that the lamp should be replaced. Replace the lamp in this case.
EN-32 Troubleshooting (continued) Images are not displayed correctly. Problem Projected images are shaking. Projected images are displaced. Projected images are distorted. Projected images are dark. Projected images are blurred. White dots are seen on projected images. Black dots are seen on projected images. Rainbow effect is seen on projected images. Fine streaks are seen on projected images. Projected images become wavy. Hue is not appropriate. Tint in projected images is incorrect. Only the motion areas in the images supplied from the computer arent displayed. Projected images are obscured.Solution •Check that the cable connected to the external device isnt intermittent. •Connect the cables plug with the external devices connector firmly. •Press the AUTO POSITION button. •Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See page 26.) •Adjust the projector and the screen so that they are perpendicular to each other. (See Page 11.) •Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See Page 24.) •Replace the lamp. (See Page 28.) •Adjust the focus. (See Pages 15 and 19.) •Clean the lens. •Press the $ or % button on the remote control to eliminate flicker. •Adjust TRACKING and FINE SYNC. in the SIGNAL menu. (See Page 26.) •Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See Page 24.) •Adjust the projector and the screen so that they are perpendicular to each other. (See Page 11.) •This symptom is normal for a DLP projector and is not a malfunction. (A very small number of pixels may stay lit or out, but such symptom is not a malfunction. Pixels of 99.99% or more are effective.) •This is due to color breaking noise that occurs in a DLP system and is not a mal- function. •This is due to interference with the screen surface and is not a malfunction. Re- place the screen or displace the focus a little. •Connect the plugs of the cables to external devices securely. •Keep the projector away from devices that emit interfering radio waves. •When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of keystone correction is as small as possible. •Check that the cables connected to the external devices are not broken. •Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 23.) •Check that the cable connected to the external device isnt broken. •This is caused by the computer being used. Contact the manufacturer of your computer. •Match the output resolution of your computer with the resolution of the projector. For the method to change the output resolution of the computer, contact the manufacturer of your computer. (See page 36.) •Some images and texts appear obscured during the keystone adjustment. In such cases, use the projector without applying the keystone adjustment. (See page 10.) No image appears on the screen. (Continued) Problem NO SIGNAL is displayed. Solution •Turn on the power of the connected device, or check whether there is something wrong with the connected device. •Check whether the external device outputs signals. (Check this especially when the external device is a notebook computer.) •Check that the cable connected to the external device isnt defective. •Check that the projector is connected to the external device using the correct terminals. •Check that the connected device is correctly selected as the input source. •When an extension cord is being used, replace it with the supplied cable and check whether images are projected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord.
EN-33 ENGLISH Others Problem The exhaust vents emit warm air. No audio is output. The menu cant be used. “TEMPERATURE!!” is displayed. The mark appears. The remote control doesnt function easily or at all. The buttons on the control panel (except for the POWER button) don’t function. Abnormal sound is heard.Solution •This air comes out after cooling the inside of the projector. You may feel hot, but this is not a malfunction. •Check that the volume isnt set to low. •The microcomputers inside the projector may be wrongly operating because of noise. ➔Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again. •This indication appears when the ambient temperature rises high. When the ambient temperature stays high, the lamp goes out. ➔Eliminate any causes of the rise in the ambient temperature. •This indication appears when the air inlet or outlet grille is blocked. When they are kept blocked, the lamp goes out. ➔Remove the objects blocking the air inlet or outlet grille. •This mark appears when ineffective operation is carried out. This isnt a product malfunction. •Check that the battery is loaded in the remote control or the battery isnt weak. (See page 8.) •Check that the remote control sensor isnt exposed to direct sunlight or fluorescent light. (See page 8.) •Use the remote control within its operation range. (See page 8.) •Use the remote control at least 10 cm away from the projector. •The password function is working. ➔Cancel the password lock or contact the person in charge of management of the projector. (See page 27.) •Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symptom is not a malfunction. If the following problem occurs after the lamp is replaced, check the following first. Problem The projector does not turn on. The STATUS indicator blinks.Solution •Fit the lamp cover securely. (See Pages 28 and 29.) •Reset the lamp operating time. (See Page 29.) •Reset the lamp operating time. (See Page 29.) Kensington Lock This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington Technology Group below. Kensington Technology Group 2855 Campus Drive San Mateo, CA 94403, U.S.A. Phone : +1- (650)572-2700 Fax : +1- (650)572-9675
EN-34
Indicators
POWER
Steady
red
Steady
green
Steady
green
STATUS
Off
Blinking
green
Steady
green
CONDITION
Stand-by
Lamp stand-by (about 1 minute)
The power is on. (Normal condition)
NOTE
The POWER button cannot be used to
switch between on and off.
POWER
Steady
green
or
Steady red
Steady red
Steady
green
Steady red
Steady red
Blinking
green/red
Blinking
green/red
STATUS
Blinking orange
Blinking green
Blinking green/red
Blinking red
Steady red
Off
Steady
or
Blinking
CONDITION
Abnormal temperature
•The ventilation grilles is clogged with dust or dirt.
•The room temperature is high.
The protection circuit is working or the lamp is in an
abnormal condition.
Lamp operation time warning. (Total lamp operation
time reached 1500 hours
*1 while the power was on.)
Lamp operation time warning. (Total lamp operation
time reached 1500 hours
*1 while the power was off.)
Lamp operation time warning. (Total lamp operation
time reached 2000 hours
*1, *2 while the power was off.)
The lamp cover isn’t closed.
Abnormal.POSSIBLE SOLUTION
•Clean the ventilation grilles.
•Relocate the projector to a cooler place.
•Wait until the STATUS indicator goes out,
then press the POWER button.
•If the above solution is not effective,
replace the lamp.
Replace the lamp.
Change with a new lamp if this problem
recurs.
Close the cover correctly.
Contact your dealer.
*
1 When LAMP MODE of the INSTALLATION menu is set to STANDARD. When it is set to LOW, this duration will be
extended.
*
2 When LAMP MODE is set to LOW, this duration will be extended up to 3000 hours.
This projector has two indicators, each of which shows the operation condition of the projector.
The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your
dealer.
Normal condition
Abnormal condition
POWER indicator
STATUS indicator
EN-35 ENGLISH Specifications The specifications and outside appearance of the projector are subject to change without prior notice. Type Model Display Technology Projection lens Light-source lamp Image size (Projection distance) Maximum number of display colors Maximum resolu- tionComputer signal Video signal Component signal Computer input Video input Audio input Speaker Control terminal/Others Operating temperatures Rated voltage Power consumption Dimensions Weight Others S-video input Video input Component video input Analog input Digital input (DVI) Audio inputDLP™ projector HC100 0.55-inch Single chip DMD (Aspect ratio 16:9) Pixel 854 x 480 = 409920 pixels F 2.4 - 2.7 f= 19 - 23 mm 200 W 40 min. to 300 max. (Projection distance 1.4 to 10.7 m) 16770000 (full-color display) Maximum resolution : 1024 x 768 dots (Analog) / compressed Panel resolution : 854 x 480 dots NTSC / PAL / NTSC 4.43 / PAL-M / PAL-N / PAL-60 / SECAM 480i, 480p, 576i, 576p, 720p, 1080i Panel resolution : 854 x 480 dots [Signal type] [Terminal type] [Line] Analog RGB D-SUB 15P 1 Digital RGB DVI 1 [Signal type] [Terminal type] [Line] Video input RCA 1 S-Video input S 1 Component video inputRCA 1 [Signal type] [Terminal type] [Line] RGB Stereo mini jack (ø3.5) 1 Component RCA (L, R) 1 Video/S-video RCA (L, R) 1 2 W Mono Round type ø4.5cm x 1 RS-232C (8-pin) +41˚F (+5˚C) to +95˚F (+35˚C) AC100 - 240V, 50/60Hz 2.9A 310 mm (W) x 100 mm (V) x 245 mm (D) * Not included protrusion. 2.9 kg Luminance signal : Vp-p=1.0 V 75Ω (negative sync) Chrominance signals : Vp-p=0.286 V 75Ω (burst signal) Vp-p=1.0 V 75Ω (negative sync) YC BCR : Vp-p=1.0 V 75Ω (Y) (negative sync) Vp-p=0.7 V 75Ω (C B, CR) RGB : Vp-p=0.7 V 75Ω (negative sync) YCBCR : Vp-p=1.0 V (Y) (negative sync) Vp-p=0.7 V (CB, CR) HD/CS : TTL-level (negative or positive polarity) VD : TTL-level (negative or positive polarity) DVI-D interface (TMDS single link) 350 mVrms, 10 kΩ or more Replacement part (Option / Not included in the box) Spare lamp 499B042-20 (VLT-HC100LP)
EN-36 TV60, 480i(525i)–15.73 59.94 854 x 480TV50, 576i(625i)–15.63 50.00 854 x 4801080i 60 (1125i 60)–33.75 60.00 854 x 480 *2 1080i 50 (1125i 50)–28.13 50.00 854 x 480480p (525p)–31.47 59.94 854 x 480 *2576p (625p)–31.25 50.00 854 x 480 *2 720p 60 (750p 60)–45.00 60.00 854 x 480 *2720p 50 (750p 50)–37.50 50.00 854 x 480PC98 640 x 400 24.82 56.42 768 x 480 CGA84 640 x 400 37.86 84.13 768 x 480CGA85 640 x 400 37.86 85.08 768 x 480VGA60 640 x 480 31.47 59.94 640 x 480 VGA72 640 x 480 37.86 72.81 640 x 480VGA75 640 x 480 37.50 75.00 640 x 480VGA85 640 x 480 43.27 85.01 640 x 480 SVGA56 800 x 600 35.16 56.25 640 x 480SVGA60 800 x 600 37.88 60.32 640 x 480 *2SVGA72 800 x 600 48.08 72.19 640 x 480 SVGA75 800 x 600 46.88 75.00 640 x 480SVGA85 800 x 600 53.67 85.06 640 x 480XGA60 1024 x 768 48.36 60.00 640 x 480 *2 XGA70 1024 x 768 56.48 70.07 640 x 480XGA75 1024 x 768 60.02 75.03 640 x 480XGA85 1024 x 768 68.68 85.00 640 x 480 MAC13 640 x 480 35.00 66.67 640 x 480MAC16 832 x 624 49.72 74.55 640 x 480MAC19 1024 x 768 60.24 75.02 640 x 480 HP75 1024 x 768 62.94 74.92 640 x 480 Specification of RGB signals in each computer mode of the projector Signal mode Resolution Horizontal Vertical Normal mode (H x V) frequency (kHz) frequency (Hz) (H x V)*1 *1 : When ASPECT in the FEATURE menu is set to AUTO. *2 : Available for the signal for DVI-D terminal. Important: •Some computers aren’t compatible with the projec- tor. •The projectors maximum resolution is 854 x 480 pixels. It may not display images of higher resolu- tions than 854 x 480 correctly. •If the resolution and frequency of your computer arent shown on the table, find the compatible resolution and frequency by changing the resolution of your computer.•Set COMPUTER INPUT in the SIGNAL menu to RGB when inputting the HDTV signal as RGB sig- nal. •TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are supplied to the VIDEO or S-VIDEO signal, the signal mode is indicated as TV60 or TV50. When they are supplied to the COMPONENT terminal, the signal mode is indicated as 480i or 576i. Connectors SERIAL (8-pin) 1 R(RED)/CR 2G(GREEN)/Y3B(BLUE)/CB4 GND5 GND6 GND7 GND8 GND9 DDC5V10 GND11 GND12 DDC Data13 HD/CS14 VD 15 DDC Clock 1 TXD IN2––3––4 GND–5––6––7 RXD OUT 8–– 1 352 681 5 116 10 15 Pin No. Name I/O COMPUTER IN / COMPONENT VIDEO IN (Mini D-SUB 15-pin) Pin No. Spec. DVI-D (HDCP) (DVI-D 24-pin) PIN No.SPECPIN No.SPEC 1 DATA 2- 13–2 DATA 2+ 14 +5V Power3 DATA 2 Shield 15 Ground4–16 Hot Plug Detect5–17 DATA 0-6 DDC Clock 18 DATA 0+7 DDC Data 19 DATA 0 Shield8–20–9 DATA 1- 21–10 DATA 1+ 22 Clock Shield11 DATA 1 Shield 23 Clock+ 12–24 Clock- 1724 16 9 8 1 Specifications (continued)
North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www.mitsubishielectric.ca Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, Canada Sales Phone :+1-(905) 475-7728 Fax :+1-(905) 475-7958 E-mail :[email protected] Technical Phone :+1-(905) 475-7728 Fax :+1-(905) 475-7958 Customer Care E-mail :[email protected] MDEA (Mitsubishi Digital Electronics America, Inc.) (Warranty Registration) http://www.mitsubishi-presentations.com/ Presentation Products Division, 9351 Jeronimo Road, Irvine, CA 92618 U.S.A Phone Main Line :+1-(949) 465-6000 Technical :+1-(888) 307-0309 Product Information :+1-(888) 307-0312 Technical Support E-mail :[email protected] Europe MEU-FRA (Mitsubishi Electric Europe B.V French Branch) 25, Boulevard des Bouvets 92 741, Nanterre CEDEX, France Sales Phone :+33 (0)1 55-68-55-07 Fax :+33 (0)1 55-68-57-31 Technical Phone :+33 (0)1 41-02-83-24 Fax :+33 (0)1 49-01-07-23 MEU-GER (Mitsubishi Electric Europe B.V. German Branch) http://www.mitsubishi-evs.de/ Gothaer Strasse 8, 40880 Ratingen, Germany MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch) http://www.mitsubishi.ie/ Westgate Business Park, Ballymount, Dublin 24, Ireland Sales Phone :+353-(0)1- 4198844 Fax :+353-(0)1-4564422 Technical Phone :+353-(0)1-4198807 Fax :+353-(0)1-4198895 MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch) Centro Direzionale Colleoni, Palazzo Persero-Ingresso 2, Via Paracelso 12, 20041 Agrate Brianza, Italy Sales Phone :+39-(0)39-60531 Fax :+39-(0)39-6053214 E-mail :[email protected] MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch) http://www.mitsubishi.nl/LCD/ProdFrame.html Nijverheidsweg 23a, 3641 RP Mijdrecht, The Netherlands Sales Phone :+31-297-282461 Fax :+31-297-283936 E-mail :[email protected] Technical Phone :+31-297-282461 Fax :+31-297-283936 E-mail :[email protected] MEU (MITSUBISHI ELECTRIC EUROPE B.V.) http://www.mitsubishi-projector.ru/ Moscow Representative Office, 12/1 Goncharnaya St. 109240, Moscow, Russia Sales Phone :+7 (095) 915 8602 Fax :+7 (095) 915 8603 MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch) http://www.mitsubishielectric.es/ Ctra. de Rubi, 76-80, 08190 Sant Cugat del Valles, Barcelona, Spain Sales Phone :+34-93.565.31.54 Fax :+34-93.589.43.88 E-mail :[email protected] Technical Phone :+34-93.586.27.51 Fax :+34-93.699.74.45 E-mail :[email protected] MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian Branch) Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden Sales Phone :+46-(0)8-6251070 Fax :+46-(0)8-6251036 Technical Phone :+46-(0)8-6251052 Fax :+46-(0)8-6251036 MEU-UK (Mitsubishi Electric Europe) http://www.mitsubishi.co.uk/evs/ Visual Information Systems Division, Travellers Lane, Hatfield, Hertfordshire, AL10 8XB Sales Phone :+44 (1707) 278684 Fax :+44 (1707) 278541 E-mail :[email protected] Technical Phone :+44 (870) 606 5008 Fax :+44 (1506) 431927 E-mail :[email protected] Russia (Mitsubishi Electric Europe B.V Moscow Representative Office) 52, bldg.5, Kosmodamianskaya Nab, 113054, Moscow, Russian Federation Sales Phone :+7 (095) 721 2070 Fax :+7 (095) 721 2071 Technical Phone :+7 (095) 721 2070 Fax :+7 (095) 721 2071 MITSUBISHI Projector Contact Information AsiaMITSUBISHI ELECTRIC RYODEN AIR-CONDITIONING & VISUAL INFORMATION SYSTEMS (HONGKONG) LTD. •Hong Kong Office Units 5-10, 20/F., Ever Gain Plaza, Tower One 88 Container Port Road, Kwai Chung, New Territories, Hong Kong. Technical Support Phone :+852 2510 0777 Fax :+852 2510 0463 •Beijing Office 9/F, Office Tower 1, Henderson Centre, 18 Jianguomennei Dajie, Dongcheng District, Beijing, 100005, China Sales & Technical Support Phone :+86 (10) 6518 2930 Fax :+86 (10) 6518 2530 •Shanghai Office 10/F, Shanghai Square Office Tower, 138 Huai Hai Zhong Road, Lu Wan District, Shanghai, 200021, China Sales & Technical Support Phone :+86 (21) 6327 2228 Fax :+86 (21) 6327 4918 •Shenzhen Office Unit 01-04, 13/F, Building A, Tian An International Building, Renmin Road South, Shenzhen, 518005, China Sales & Technical Support Phone :+86 (755) 518 6386 Fax :+86 (755) 218 4775 •Chengdu Office Block B-1, 23/F., Chuan Xin Mansion, 18 Section 2, Renmin Road South, Chengdu, 610016, China Sales & Technical Support Phone :+86 (28) 619 9730 Fax :+86 (28) 619 9801 MEAP (Mitsubishi Electric Asia Pte Ltd) http://www.mitsubishielectric.com.sg 307 Alexandra Road, Mitsubishi Electric Building, 289245,Singapore Main Line Phone :+65 6 473 2308 Fax :+65 6 475 9503 Sales & Technical Support E-mail :[email protected] AMS (Antah Melco Sales & Services Sdn Bhd (A Joint-Venture Company of Mitsubishi Electric Corporation)) http://www.antahmelco.com.my 6, Jalan 13/6, Petaling Jaya, Selangor Darul Ehsan, Malaysia Main Line Phone :+603-7955 2088 Fax :+603-7956 3950 :+603-7958 2576 Technical Support Phone :+603-7955 2088 E-mail :[email protected] Product Information Phone :+603-7955 2088 ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.) http://www.mitsubishi-electric.com.tw 9th Floor., 90 Sec. 6, Chung Shan N. Rd., Taipei, Taiwan Sales Support Phone :+886 (0) 2 2832 8255 Fax : +886 (0) 2 2833 9813 KYW (Kang Yong Watana Co., Ltd.) http://www.mitsubishi-kyw.in.th 28 Krungthep Kreetha Road, Huamark Bangkapi, Bangkok, 10240, Thailand Sales Support Phone :+66 (2) 731 6901 Fax :+66 (2) 379 4763 STC (Setsuyo Astec Corp. Seoul Branch) Dongseo Game Channel Bldg, 660-11, Deungchon-dong, Kangseo-ku, Seoul, Korea Main Line Phone :+82 (0) 2 3665 4964 Fax :+82 (0) 2 3665 4965 Oceania ME-AUST (Mitsubishi Electric Australia) http://www.mitsubishi-electric.com.au/prod.asp?prod=proj 348 Victoria Road, Rydalmere, N.S.W. 2116, Australia Sales Phone :+(612)9684-7777 Fax :+(612)9898-0484 E-mail :[email protected] BDT (Black Diamond Technologies Ltd.) (Warranty Registration) http://www.bdt.co.nz/projectors/warranty.asp 1 Parliament St, Lower Hutt, Wellington, New Zealand Sales Phone :+64-(0)4-560-9100 Fax :+64-(0)4-560-9133 E-mail :[email protected] Technical Phone :+64-(0)4-560-9100 Fax :+64-(0)4-560-9133 Manufactured by Mitsubishi Electric Corporation 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan MITSUBISHI ELECTRIC CORPORATION Printed in JAPAN 871D423A30