Mitsubishi Electronics Projector XD110U SD110U User Manual

							EN-11
ENGLISH
Projector + Computer 
For computer with Mini D-SUB  
Important: 
 When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
 Some computers require additional connectors or analog RGB output adapters to be connected with this projector. Contact your 
dealer for further information. 
 This projector uses stereo pin jack for its audio input. Check the type of the audio output terminal of the connected computer and 
prepare a proper cable for connection. Some computers don’t have the audio output terminal. 
 Speaker output is mono. 
 When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted. 
For Macintosh 
 If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further information. 
 Some Macintoshes require a MAC adapter for the RGB cable for connection with this projector. Contact your dealer for further 
information. 
About DDC 
The COMPUTER IN terminal of this projector complies with the DDC1/2B standard. When a computer supporting this standard is 
connected to this terminal, the computer will automatically load the information from this projector and prepare for output of appropri-
ate images. 
 After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the wall outlet first, 
and then boot up the computer. 
 You may need to install the DDC driver, depending on the computer you use. In this case, you need to download the driver from 
our Web site. Contact your dealer or Mitsubishi sales office for further information. 
 
AUDIO OUT
MONITOR OUTPUT
COMPUTER INRGB cable for PC
AU D I O  OU T
Audio cable (option)
MONITOR OUT
Necessary when outputting to both 
a PC monitor and the projector.
PC audio cable (option) AU D I O  I N
to PC audio 
outputComputer
to monitor 
port
RGB cable for PC (option) 
						

							EN-12
Preparation
Preparation for projection 
1. Attach the provided power cord to the projector. 
2. Plug the power cord in the wall outlet. 
3. Remove the lens cap. 
Warning: 
 Do not look into the lens directly when the projector is on. 
 The lens cap is for protecting the lens. If you leave the lens 
cap on the lens with the projector turned on, it may be 
deformed because of heat build-up. Remove the lens cap 
when you turn on the projector. 
 The power cords for use in the U.S. and Europe are pro-
vided with this projector. Use the appropriate cord for your 
country. 
 This projector uses the power plug of three-pin grounding 
type. Do not remove the grounding pin from the power plug. 
If the power plug doesn’t fit your wall outlet, ask an electri-
cian to change the wall outlet. 
 The provided power cord for the U.S. is rated at 120 V. 
Never connect this cord to any outlet or power supply using 
other voltages or frequencies than rated. If you want to use 
a power supply using other voltage than rated, prepare an 
appropriate power cord separately. 
 Use 100-240 V AC 50/60 Hz to prevent fire or electric 
shock. 
 Do not place any objects on the power cord or do not place 
the projector near heat sources to prevent damage to the 
power cord. If the power cord should be damaged, contact 
your dealer for replacement because it may cause fire or 
electric shock. 
 Do not modify or alter the power cord. If the power cord is 
modified or altered, it may cause fire or electric shock. 
Caution: 
 Plug in the power cord firmly. When unplugging, hold and 
pull the power plug, not the power cord. 
 Do not plug in or out the power cord with your hand wet. It 
may cause electric shock. 
Adjustment of the projection angle 
For the best projection, project images on a flat screen 
installed at 90 degrees to the floor. If necessary, tilt the projec-
tor using the two adjustment feet on the bottom of the projec-
tor.
 1. Tilt up the project to the appropriate angle. 
2. Press the foot adjustment buttons next to the adjustment 
feet (rear), and the adjustment feet will come out. 
3. Release the buttons to lock the adjustment feet (rear) to 
that position. 
4. Rotate the adjustment feet (rear) for fine adjustment. 
After using the projector: 
5. Put the adjustment feet (rear) back into the projector by 
pressing the foot adjustment buttons. 
Important: 
 If necessary, rotate the adjustment feet (front) for fine 
adjustment. 
 Install the screen on a flat wall at 90 degrees to the floor. 
 Slanting the projector more than ±10° (right and left) or ±15° 
(front and rear) may cause trouble or explosion of the lamp. 
You can tilt the projector up to 7 degrees using the adjust-
ment feet only. 
 Images may not be projected in a shape of a regular rectan-
gle or with its aspect ratio 4:3, depending on the installation 
conditions of the projector and the screen. 
 To correct vertical keystone distortion, press the KEY-
STONE button on the projector or the remote control to dis-
play KEYSTONE, and adjust the image by pressing the S, 
T button (or VOLUME +, - button on the remote control). 
In the following cases:  
Important: 
 When the keystone adjustment is carried out, the adjust-
ment value is indicated. Note that this value doesn’t mean a 
projection angle. 
 The allowable range of the adjustment value in the keystone 
adjustment varies depending on the installation conditions. 
 When the keystone adjustment takes effect, the resolution 
decreases. In addition, stripes may appear or straight lines 
may bend in images with complicated patterns. They are 
not due to product malfunctions. 
 Noise may appear on the screen during the keystone 
adjustment because of the type of the video signal being 
projected and the setting values of the keystone adjust-
ment. In such cases, set the keystone adjustment values in 
the range where the image is displayed without noise. 
 When the keystone adjustment is carried out, the image 
may not be displayed correctly because of the type of input 
signal. 
For SD110U only 
 When the 720p or 1080i signal is input, the keystone adjust-
ment ranges are limited. 
 
Screen
Adjustment feet
Press the T  
(or -) button.Press the S  
(or +) button. 
						

							EN-13
ENGLISH
Basic operation
Power-on 
1. Turn on the device connected to the projector first. 
2. Plug the power cord in the wall outlet. 
 The POWER indicator lights up. 
 If the power cord is unplugged from the wall outlet 
before the projector is cooled down completely after 
use, the fans may start rotating when the power cord is 
plugged in next time and the POWER button may not 
function. In this case, wait for the fans to stop and press 
the POWER button to light the indicator. 
3. Press the POWER button on the control panel or the ON 
button on the remote control. 
 It may take about one minute for the lamp to light up. 
 The lamp occasionally fails to light up. Wait a few min-
utes and try to light the lamp again. 
 After the POWER button is pressed, the image may 
flicker before the lamp becomes stable. This is not a 
product malfunction. 
 Regardless of the setting of LAMP MODE in the 
INSTALLATION menu, the STANDARD lamp mode is 
activated by default whenever the projector is turned 
on. When LAMP MODE has been set to LOW, the lamp 
mode changes from STANDARD to LOW about one 
minute after turn-on. 
Important: 
 Do not cover the lens with the lens cap while the lamp is on. 
Do not strip off the aluminum sheet inside the lens cap.
 The projector starts warming up when the POWER button is 
pressed. During the warm-up process, images may appear 
dark and no commands are accepted. 
 By blinking red, the STATUS indicator indicates that the 
lamp should be replaced soon. Replace the lamp when the 
STATUS indicator blinks red. (See page 23 and 26.)  Images may not be projected with good quality in an 
extremely hot or cold environment. (This is not a product 
malfunction.) 
4. Adjust the focus by turning the focus ring. 
5. Choose your desired external input source using  the 
COMPUTER or VIDEO button. 
 The input source is switched from VIDEO to COM-
PUTER at the press of the COMPUTER button on the 
control panel.
 The input source is switched between VIDEO(1) and S-
VIDEO(2) at every press of the VIDEO button on the 
control panel. 
 The projector automatically selects the appropriate sig-
nal format. The selected signal format is displayed on 
the screen. 
 The COMPUTER and VIDEO buttons don’t function 
while the menu is being displayed. 
 When COMPUTER is chosen as the source, images 
supplied from the computer may flicker. Press the W or 
X button on the remote control to reduce flicker, if it 
occurs. 
 To avoid permanently imprinting a fixed image onto 
your projector, please do not display the same station-
ary images for long period. 
6. Adjust the image size by turning the zoom ring. 
 If necessary, adjust the focus and zoom again. 
STILL
ON POWER OFF
MUTE
MENU
COMPUTER
16:9
AUTO POSITIONPAGE
DOWN
ENTER
VIDEO12
KEYSTONEVOLUME
UP
5 31, 2
3, 1, 2 55
4
6
Indicator
ConditionSTATUS POWER
Stand-by - Red
When the lamp is on. Green Green 
						

							EN-14
Basic operation (continued)
Power-off 
Use the following procedure to turn off the projector. Do not 
turn off the projector by unplugging the power cord while the 
lamp is on. Unplugging while the lamp is on degrades the 
lamp’s performance and causes failure in the projector. 
1.Press the POWER button on the control panel or the OFF 
button on the remote control. 
 The message POWER OFF? YES : PRESS AGAIN 
appears on the screen.
 To cancel, press any button except the POWER button. 
(Some buttons on the remote control don’t function for 
cancel.) 
2.Press the POWER button on the control panel or the OFF 
button on the remote control within 10 seconds again. 
 The lamp will go out and the STATUS indicator will start 
blinking. 
 Though the lamp goes out at this second press of the 
POWER button (or OFF button), the air outlet fans con-
tinue operating for one minute to cool down the lamp. 
The STATUS indicator will stop blinking. 
3.Unplug the power cord. 
 The POWER indicator will go out. 
 If the power cord should be unplugged accidentally 
while either the air inlet fan or the air outlet fans are 
operating or the lamp is on, allow the projector to cool 
down for 10 minutes with the power off. To light the 
lamp again, press the POWER button (or OFF button). 
If the lamp doesn’t light up immediately, repeat pressing 
the POWER button (or OFF button) two or three times. 
If it should still fail to light up, replace the lamp. 
Important: 
 When storing the projector in the provided carrying case, 
the lens should face up. 
AUTO POSITION button 
When the image isn’t projected in the right position with COM-
PUTER selected as the input source, follow the procedure 
below. 
1. Project a bright image such as the Recycle Bin window 
on the full screen. 
2. If the screen saver is running, turn it off. 
3. Press the AUTO POSITION button. 
 If the image is still not in the right position, adjust the 
image position using the SIGNAL menu. See page 19. 
Volume from the speaker 
Press the VOLUME + or -button to change the volume 
from the speaker.
The volume control bar will appear on the screen.
 The volume control bar will disappear about 10 seconds 
after the VOLUME button is released. 
 The VOLUME buttons don’t function while the menu selec-
tion bar or the menu is being displayed. 
 When a high-level audio signal, such as a DVD audio signal, 
is supplied to the AUDIO IN terminal, the output from the 
speaker may be distorted. 
AV  m u t e  
The video and audio signals are temporarily muted when the 
MUTE button is pressed. To cancel muting, press the MUTE 
button again. 
ANAMORPHIC mode 
When playing DVD discs containing data of letterboxed image, 
press the 16:9 button. Exit the ANAMORPHIC mode, by press-
ing the 16:9 button again. 
Important: 
 When a letterboxed image is kept displayed for a long time 
before displaying 4:3 image, the afterimages of the black 
bars may appear on the 4:3 image screen. Consult your 
dealer in this case. 
Caution: 
 After using the projector, wait one minute for the air outlet 
fans to stop. Then unplug the power cord from the wall out-
let. 
 The lamp can’t be lit again for one minute after turned off for 
safety purpose. It will take another one minute for the STA-
TUS indicator to go out. If you want to turn on the projector 
again, wait until the indicator goes out, and then press the 
POWER button. 
 The air outlet fans rotate faster as the temperature around 
the projector rises. 
 When the temperature around the projector rises high, the 
sign TEMPERATURE!! blinks red on the screen. If the 
temperature stays high, the lamp will go out automatically. 
Important: 
 Do not display a still picture for a long time because the 
afterimages may persist on the screen.  
 
VOLUME     10 
						

							EN-15
ENGLISH
Menu operation
Basic operation
Several settings can be adjusted using the menu. OFF.
Example : Auto power off time setting
1. Press the MENU button.
2. Press the W or X button to select INSTALLATION. 
3. Press the ENTER button (or T button).4. Press the S or T button to select AUTO POWER OFF.
5. Press the W or X button to adjust the auto power off time.
6. Exit the menu by pressing the MENU button several times.
Important: 
 When the button doesn’t function, unplug the power cord 
from the wall outlet. Wait about 10 minutes, plug the power 
cord in, and try again.  
 After selecting the items marked with  , press the ENTER 
button. 
IMAGE CONTRAST ±30
BRIGHTNESS ±30
WHITE ENHANCE AUTO, 0 - 10
STANDARD
LOW
HIGH
USER     COLOR TEMP.
COLOR  ±10
TINT  ±10
SHARPNESS  ±5
GAMMA MODE AUTO, DYNAMIC, STANDARD, THEATERCONTRAST R  ±30
CONTRAST B  ±30
BRIGHTNESS R  ±30
BRIGHTNESS B  ±30
INSTALLATION
OFF, MIRROR, INVER T, MIRROR INVERT
AUTO POWER ON
ON , OFF
RESET ALL OK  AUTO POWER OFF
ON , OFF
FEATURE MENU POSITION 1 (Upper left), 2(Lower right)IMAGE REVERSE SPLASH SCREEN
BLUE, BLACK BACK COLOR
STANDARD, LOW LAMP MODE
MENU ACCESS PASSWORD FUNCTION
VIDEO SIGNAL AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
LANGUAGE
SIGNALHORIZ.POSITION
HOLD0 - 999
VERT.POSITION 0 - 999
FINE SYNC. 0 - 31
TRACKING
USER0 - 9999
CLAMP POSITION0 - 63
CLAMP WIDTH 1 - 63 *4
*2
*2
*2
*2
*2
AUTO , OFF CINEMA MODE
*4
*4
ON
BEGIN 0 - 15
END 0 - 15 OFF
COMPUTER INPUTRGB, YCBCR / YPBPR
SET UPOFF / 3.5% / 7.5%
*4
*4 *4
*4
OFF,  5,  10,  15,  30,  60 min
OK 
ON , OFF ANAMORPHIC
ON
UNLOCKOK 
LOCK *1
*3 *1
(These items are not available when the 
input sour ce is COMPUTER.)
* 1: Not available with certain signals.
* 2: Not available when the source is a VIDEO or S-VIDEO signal.
* 3: Available only when the input signal is TV60, 480i. 
* 4: Setting range differs depending on the input signals. 
IMAGE
XGA60opt.
INSTALLATION
opt.XGA60
INSTALLATION
opt.
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
XGA60
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
AUTO POWER 
ON
AUTO POWER 
OFF
30 minOFF 
						

							EN-16
Menu operation (continued)
1IMAGE
CONTRAST ................................. Use to adjust the image contrast. The contrast 
becomes higher as the value increases.
BRIGHTNESS ............................. Use to adjust the image brightness. The image 
becomes brighter as the value increases.
WHITE ENHANCE ...................... Use to adjust the white level of the projected image. 
Select AUTO for normal use.
COLOR TEMP ............................. Use to adjust the color temperature. See page 18.
COLOR ........................................ Use to adjust the color intensity of the image.
TINT............................................. Use to adjust the color balance of the image. The 
color balance shifts to green as the value increases 
and shifts to purple as the value decreases. (Avail-
able only when VIDEO or S-VIDEO is chosen as the 
source.) 
 When the TV50 (PAL, SECAM) signal is input, TINT can’t be adjusted. 
SHARPNESS .............................. Use to adjust the image sharpness. The image becomes sharp as the value increases. (Not 
available with certain signals.) 
GAMMA MODE  .......................... When AUTO is selected, the appropriate gamma mode is automatically selected depending on 
the input signal. For normal use, select AUTO. Select DYNAMIC for computer sources. Select 
STANDARD for sport scenes and video sources. Select THEATER for film sources. 
2 INSTALLATION 
AUTO POWER ON ...................... When ON is chosen, the lamp is automatically lit 
when the power cord is plugged in the wall outlet. 
Choose ON when using the projector mounted on the 
ceiling. 
 The projector is in the stand-by mode when the 
lamp is off.  Use the remote control to turn on the 
lamp. 
AUTO POWER OFF .................... Use to set the time elapsed before the projector 
enters the stand-by mode when there is no signal 
input from the source. 
SPLASH SCREEN ...................... Choose ON to display the splash screen when the 
power is turned on. 
BACK COLOR ............................. Use to select the background from among BLUE and BLACK, which will be displayed when there 
is no signal input from the source. 
LAMP MODE ............................... Use to change the brightness of the lamp. When LOW is chosen, the lamp brightness is kept low 
and the projector operating noise is reduced, resulting in a longer lamp replacement interval. 
 When the lamp mode is switched, the projected image may flicker. This is not a product mal-
function. 
 Do not change the setting of LAMP MODE frequently.  
 When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW 
about one minute after turn-on. 
IMAGE REVERSE ....................... Use to reverse the projected image. Select MIRROR for rear projection with the tabletop-
mounted projector. Select MIRROR INVERT for front projection with the ceiling-mounted projec-
tor.  
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
WHITE ENHANCE AUTO
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE
opt.
INSTALLATION
opt.
ON
BACK COLOR AUTO POWER 
ON
AUTO POWER 
OFF
SPLASH 
SCREEN
LAMP MODEON
BLUEOFF OFF
STANDARD
OFF IMAGE 
REVERSE
XGA60 
						

							EN-17
ENGLISH
3 FEATURE
MENU POSITION ....................... Use to select the position of the menu on the screen, 
1.   (upper left) or 2.   (lower right). 
CINEMA MOD ............................. When AUTO is selected, the film mode will be auto-
matically activated when a film source signal is input-
ted. When OFF is selected, the film mode will not be 
activated.
VIDEO SIGNAL ........................... When AUTO is selected, the appropriate video format 
is automatically selected depending on the input sig-
nal. If the image isn’t displayed correctly, select the 
desired video format manually.
ANAMORPHIC ............................ Select ON when playing DVD discs containing data of 
widescreen images. 
PASSWORD FUNCTION.............. Use to change the mode of the password lock or to enable or cancel the password lock. See 
page 21 for details. 
LANGUAGE ................................ Use to select the language used in the menu. (  / English / Español / Deutsch / Français / 
Italiano /   /   /   / PORTUGUÊS).
RESET ALL ................................. Use to reset the menu settings (except PASSWORD FUNCTION, and LANGUAGE ). 
 CINEMA MODE can be adjusted only when a TV50, TV60, 480i, 576i signal is being displayed. 
 When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of VIDEO SIG-
NAL depending on the input signal in such cases. 
4 SIGNAL 
HORIZ. POSITION ...................... Use to adjust the horizontal position of the image.  
VERT. POSITION ........................ Use to adjust the vertical position of the image. 
FINE SYNC ................................. Use to synchronize the projector with the PC input 
signal so that the image is not blurred.
TRACKING .................................. Use to eliminate image noise such as wide stripes.
COMPUTER INPUT  ................... The projector adjusts its settings automatically when 
connected to a DVD player equipped with a compo-
nent video output (Y, C
B, CR). When the projector is 
connected with a device having an RGB terminal, 
choose RGB manually. 
SET UP ....................................... When OFF is selected, the black area becomes make 
lighter. When 3.5% or 7.5% is selected, the black 
area becomes thicker. 
HOLD  ......................................... Use to adjust the image when flagging occurs near the top of the screen. 
5 SIGNAL - USER (No need to adjust in normal use.) 
CLAMP POSITION/ 
CLAMP WIDTH ........................... Use to correct solid white or solid black in the pro-
jected image. 
Important: 
 You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is supplied.  
 
FEATURE
XGA60
AUTO
opt.
MENU POSITION
VIDEO SIGNAL?
RESET ALL
English
LANGUAGEAË
OK
MENU ACCESS PASSWORD
FUNCTION
ANAMORPHICCINEMA MODEAUTO
1.
ON
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTRGB
FINE SYNC. 0
USER
XGA60opt.
OK
ONHOLD
7.5%
SET UP
CLAMP 
POSITIONUSER
0
CLAMP WIDTH 1 
						

							EN-18
Image adjustment
Image adjustment
You can adjust the image using the IMAGE menu. 
To control the white-to-black level of the image : 
Adjust CONTRAST in the IMAGE menu. Press the X button to 
increase the contrast and the W button to reduce it. 
To control the light level of the image : 
Adjust BRIGHTNESS in the IMAGE menu. Press the X button 
to lighten the image and the W button to darken it. 
To determine the intensity of the color : 
Adjust COLOR in the IMAGE menu. Press the X button to 
increase the amount of color in the image and the W button to 
decrease it. 
To adjust the red-green color balance of the image : 
Adjust TINT in the IMAGE menu. Press the X button to 
increase the amount of green in the image and the W button to 
increase the amount of red in the image. 
To adjust the detail and clarity of the image : 
Adjust SHARPNESS in the IMAGE menu. Press the X button 
to sharpen the image and the W button to soften the image. 
Color temperature
1. Select COLOR TEMP. in the IMAGE menu.
2. Press the W or X button to select USER  . 
3. Press the ENTER button.
4. Press the S or T button to select the desired item.
5. Press the W or X button to adjust the selected item. 
6. Repeat steps 4 and 5 for optimum adjustment results. 
7. Exit the menu by pressing the MENU button several times. 
 
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
WHITE ENHANCE AUTO
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE
opt.
About color temperature 
There are different kinds of white color. Color temperature 
is a way to show the differences in white. 
White of which temperature is low appears reddish. 
When the color temperature rises, white appears bluish. 
This projector adjusts this color temperature by changing 
the values of contrast blue and red.
To rise the color temperature:
Increase the CONTRAST B (blue) and decrease the 
CONTRAST R (red).
To reduce the color temperature:
Decrease the CONTRAST B (blue) and increase the 
CONTRAST R (red).
CONTRAST R
USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0 
						

							EN-19
ENGLISH
Adjustment of the image from the computer 
This projector adjusts the format of the video signal supplied 
from the computer. However, sometimes images are not pro-
jected correctly owing to the type of the computer used. When 
the image from the computer isn’t projected correctly, press 
the AUTO POSITION button. (See page 14.) If the image isn’t 
projected correctly yet, adjust the image from the computer 
using the menu.  
To move the image horizontally : 
Adjust HORIZ. POSITION in the SIGNAL menu. Press the X 
button to move the image to the left. Press the W button to 
move the image to the right. 
To move the image vertically : 
Adjust VERT. POSITION in the SIGNAL menu.  Press the X 
button to move the image upward.  Press the W button to move 
the image downward. 
When the image flickers or the image is out of focus : 
Adjust FINE SYNC. in the SIGNAL menu. 
When the top part of the image flags : 
Change the setting of HOLD in the SIGNAL menu. Select ON 
, press the ENTER button, and adjust BEGIN or END to 
minimize the flagging.  
When wide strips appear : 
Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL - 
USER menu. 
Important: 
Do not change any of the settings in the SIGNAL-USER menu 
for normal use.  
Simple adjustment method 
1. Select HORIZ. POSITION in the SIGNAL menu. 
2. Press the W or X button to adjust the horizontal start posi-
tion (or the left side of the image). 
3. Select TRACKING in the SIGNAL menu. 
4. Press the W or X button to adjust the horizontal end posi-
tion (or the right edge of the image). 
5. Repeat steps 1 to 4 for optimum adjustment results. 
6. Select VERT. POSITION in the SIGNAL menu. 
7. Press the W or X button to adjust the vertical start position 
(or the upper edge of the image). 
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTRGB
FINE SYNC. 0
USER
XGA60opt.
OK
ONHOLD
7.5%
SET UP
CLAMP 
POSITIONUSER
0
CLAMP WIDTH 1 
						

							EN-20
Advanced feature
Still 
To stop the motion in the image temporarily (or to display a still 
image):
Press the STILL button on the remote control.
 The image will freeze temporarily. 
To resume the motion in the image: 
Press the STILL button on the remote control again. 
Important: 
 Do not display a still picture for a long time because the 
afterimages may persist on the screen. 
Page-up and page-down 
You can control the computer to page-up and page-down the 
presentation data using the remote control. Switch the pages 
using the PAGE UP or DOWN button on the remote control. 
Connection 
To control the computer using the remote control, connect the 
projector with the computer as shown below.  
 Only the computers equipped with a USB port are sup-
ported. 
 Wait for the lamp to light up before connecting the USB 
cable. 
USB
USB 4-pin
(type B)
USB 4-pin
(type A) to USB port
USB cable
(option)