Mitsubishi Electronics Projector XD490U XD460U User Manual

							EN-31
ENGLISH
Replacing the lamp
This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness 
may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the 
lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp. 
WARNING:
•  Be careful not to drop the lamp fi xing screws into the inside of the projector. Don’t put a metal piece or fl ammable 
object into the projector. Using the projector with any foreign object present inside may result in electric shock or 
fi re. When you can’t remove the foreign object from the inside, contact your dealer for removal. 
•  Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation 
may also result in fi re.
•  Don’t shake the removed lamp or don’t lift it above your face. You may be injured in your eye by fl ying or falling 
glass fragments.
•  Don’t replace the lamp immediately after use because the lamp cover is very hot. You may get burned. Turn off the 
power using the POWER button. After the lamp goes out, wait about 2 minutes until the intake and exhaust fans 
for cooling the lamp stop rotating. Then unplug the power cord, and wait at least 1 hour to allow the lamp to cool 
down enough to the touch.
•  Do not touch the lamp directly. It may break and cause injury or burn.
Interval of lamp replacement
The recommended interval of lamp replacement is about 5000 hours*1 *2 of consecutive use. Such interval differs 
depending on the operating environment and may be shorter than 5000 hours*1 *2. Decrease in luminescence and/or 
color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 3750 hours*1, 
the indicator will blink alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator 
will be lit red only) and the lamp replacement message will appear on the screen for 1 minute everytime the lamp is 
turned on. When the lamp has been used for about 4750 hours
*1, the replacement message (LAMP EXCHANGE) will 
appear on the screen for 1 minute every 25 hours*1 thereafter.
When the lamp operation time exceeds 5000 hours
*1 *2, the projector automatically shuts off and can’t be used 
until the lamp is replaced and the lamp operation time is reset.
*1   Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration 
will be shorted.
*2   Duration when LAMP MODE is set to STANDARD, this duration will be shorted to 2000 hours.
Caution:
•  Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a 
breakdown.
•  This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may 
explode or fail to illuminate permanently because of an impact, scratch, or deterioration through use. The period 
of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on 
operation conditions. Therefore, the lamp may explode soon after the start of use. 
•  The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction 
of lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting normally. 
•  When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and 
the gas charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains 
mercury. Be careful not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it 
should enter your eye or mouth, see a doctor immediately.
•  In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the 
projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace 
the lamp by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments. 
•  Don’t replace the lamp while the projector is installed on the ceiling. Glass fragments may fall from the projector, 
entering your eye or mouth causing injury. 
•  When placing the projector upside down to replace the lamp or conduct maintenance, ensure that the projector is 
securely placed before working with it. 
						

							EN-32
(c)
(a)(b)
(c)
To replace the lamp: 
1.  Reverse the projector gently.
2.  Loosen the screw (a) using a Phillips screwdriver (+), and 
remove the lamp cover (b).
3.  Loosen the screws (c) using a Phillips screwdriver (+).
4.  Pull up the handle. 
5.  Pull out the lamp box by the handle while holding the 
projector.
•  Pull the lamp box out of the projector slowly. If it is 
pulled out quickly, the lamp may break scattering glass 
fragments. 
•  Do not spill liquid on the removed lamp box or do not 
place it near any fl ammable object or where children 
can reach to prevent injury or fi re.
6.  Load a new lamp box securely into the projector in the right 
orientation.
7.  Put the handle back to the original position.
•  Make sure that the handle is locked.
8.  Tighten up the screws (c) using a Phillips screwdriver (+).
9.  Tighten up the screw (a) using a Phillips screwdriver (+) to 
secure the lamp cover.
Reset of the lamp operation time
Press the 
, 
, and POWER button on the control panel at the same time.
Important:
•  Unless these 3 buttons are pressed at the same time, the lamp operation time isn’t reset. 
•  Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully. 
•  The projector doesn’t turn on if the lamp cover isn’t attached securely. 
•  Be sure to reset the lamp operation time whenever you replace the lamp. 
•  Do not reset the lamp operation time unless you replace the lamp. 
•  The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.
•  Contact your dealer for a new lamp.
•  This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be 
regulated due to environmental considerations. For disposal or recycling information, please contact your local 
authorities or the Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)
Maintenance
Caution:
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on 
the projector. 
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft 
cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.
To protect the surface of the projector from fading or deteriorating:
•  Do not spray insecticide on or inside the projector.
•  Do not use benzine or thinner to clean it.
•  Do not let rubber or plastic materials contact with projector.
Cleaning of the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fl uid. The lens surface is 
fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fi ngers.
Replacing the lamp  (continued) 
						

							EN-33
ENGLISH
POWER
Off
Steady red
Blinking 
red / green
STATUS
Off
Off
Blinking 
orange
Blinking 
green
Steady red
Off
Steady
or
Blinking
  Solution
•  Connect the power cord to the projector. 
•  Plug the power cord into a wall outlet. 
•  If any objects are blocking the air inlet or outlet grille, remove them and carry 
out the following.
1.  Unplug the power cord from the wall outlet.
2.  Make sure that the projector has cooled off. 
3.  Plug the power cord into the wall outlet.
4.  Press the POWER button.
•  If any objects are blocking the air inlet or outlet grille, remove them.
•  Don't expose the air outlet grilles to hot air emitted from a heating appliance.
•  After the STATUS indicator stops blinking, press the POWER button.
•  If you unplug the power cord while the fan is rotating, the lamp may not turn on about 1 minute when 
you plug the power cord next time. 
•  The lamp can't turn on again for 1 minute after it goes out. 
•  Press the POWER button several times.
•  Replace the lamp. (The lamp is at the end of its life.)
•  Attach the lamp cover on the bottom.
•  Unplug the power cord from the wall outlet and contact your dealer.
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be 
sure to unplug the power plug, and then contact your dealer. 
No image appears on the screen. 
Problem
Power can not be 
turned on.
No image appears on 
the screen. 
Projected images 
suddenly disappear. Solution
•  Check whether the indicators are on or off and how they are lightning.
• Cancel the AV mute by pressing the MUTE button.
•  Check that the lens cap is removed. 
•  It may take about 1 minute for the lamp to light up. 
•  The lamp fails to light up on rare occasions. In such a case, wait for a few minutes 
and then try again. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, 
the fan may start rotating and the POWER button may not work after the power cord 
is plugged. After the fan stops rotating, press the POWER button to turn back on the 
POWER indicator. 
• Set SCART INPUT in the FEATURE menu to OFF. (See page 24.)
•  Check that the intake vent is clean. 
•  Check that the lamp cover is closed. (See page 32.)
•  Check that the cables connected to the external devices are not broken. 
•  When an extension cable is being used, replace it with the supplied cable for check. 
When images are displayed correctly, add an RGB signal amplifier to the extension 
cable. 
•  This problem may occur when the intake vent and/or exhaust vents are blocked. (In 
such a case, the STATUS indicator brinks orange.)
  Remove the objects blocking the intake vent and/or exhaust vents and then carry 
out the following procedure. 
1.  Wait for the intake fan and/or exhaust fan to stop.  (Wait until the STATUS 
indicator goes out.) 
2.  Unplug the power cord from the wall outlet. 
3.  Wait about 10 minutes.
4.  Plug the power cord into the wall outlet. 
5.  Press the POWER button. 
•  When the STATUS indicator is steady red, it is indicating that the lamp should be 
replaced. Replace the lamp in this case. 
• PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT to 
enable the password lock. 
 Enter the password or contact the person in charge of management of the projec-
tor. (See page 28.)The screen for entering 
the password appears. 
						

							EN-34
Images are not displayed correctly. 
Problem
Projected images are 
shaking.
Projected images are 
displaced. 
Projected images are 
distorted. 
Projected images are 
dark. 
Projected images are 
blurred. 
White dots are seen 
on projected images. 
Black dots are seen on 
projected images. 
Rainbow effect is seen 
on projected images. 
Fine streaks are seen 
on projected images. 
Projected images 
become wavy. 
Hue is not appropriate. 
Tint in projected 
images is incorrect.
Only the motion areas 
in the images supplied 
from the computer 
aren't displayed. 
Projected images are 
obscured.Solution
•  Check that the cable connected to the external device isn't intermittent. 
•  Connect the cable's plug with the external device's connector fi rmly.
•  Press the AUTO POSITION button.
•  Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL 
menu. (See page 27.)
•  Adjust the projector and the screen so that they are perpendicular to each other. (See 
page 12.)
•  Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 25.)
•  Replace the lamp. (See page 31.)
•  Adjust the focus. (See pages 15 and 19.)
•  Clean the lens. 
• Press the 
 or 
 button on the remote control to eliminate fl icker. 
•  Adjust TRACKING and FINE SYNC. in the SIGNAL menu. (See page 27.)
•  Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 25.)
•  Adjust the projector and the screen so that they are perpendicular to each other. (See 
page 12.) 
•  This symptom is normal for a DLP
TM projector and is not a malfunction. (A very small 
number of pixels may stay lit or out, but such symptom is not a malfunction. Pixels of 
99.99% or more are effective.) 
•  This is due to color breaking noise that occurs in a DLP
TM system and is not a 
malfunction. 
•  This is due to interference with the screen surface and is not a malfunction. Replace 
the screen or displace the focus a little. 
•  Connect the plugs of the cables to external devices securely. 
•  Keep the projector away from devices that emit interfering radio waves. 
•  When the keystone adjustment is carried out, the image may not be displayed 
correctly depending on the type of input signal. This isn’t a product malfunction. In 
this case, readjust the keystone so that the amount of keystone correction is as small 
as possible.
•  Check that the cables connected to the external devices are not broken. 
•  Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 24.)
•  Check that the cable connected to the external device isn't broken. 
•  This is caused by the computer being used. Contact the manufacturer of your 
computer.
•  Match the output resolution of your computer with the resolution of the projector.  For 
the method to change the output resolution of the computer, contact the manufacturer 
of your computer. (See page 38.)
•  Some images and texts appear obscured during the keystone adjustment. In such 
cases, use the projector without applying the keystone adjustment. (See page 10.)
No image appears on the screen. (continued) 
Problem
"NO SIGNAL" is 
displayed.Solution
•  Turn on the power of the connected device, or check whether there is something 
wrong with the connected device.
•  Check whether the external device output signals. (Check this especially when the 
external device is a notebook computer.) 
•  Check that the cable connected to the external device isn't defective. 
•  Check that the projector is connected to the external device using the correct 
terminals. 
•  Check that the connected device is correctly selected as the input source. 
•  When an extension cord is being used, replace it with the supplied cable and check 
whether images are projected correctly. If images are projected correctly, use an RGB 
signal amplifi er along with the extension cord. 
Troubleshooting (continued) 
						

							EN-35
ENGLISH
Others
Problem
The exhaust vents 
emit warm air.
No audio is output. 
The menu can't be 
used. 
“TEMPERATURE!!” is 
displayed.
The 
 mark appears. 
The remote control 
doesn't function easily 
or at all.
The buttons on the 
control panel (except 
for the POWER 
button) don’t function. 
Abnormal sound is 
heard. Solution
•  This air comes out after cooling the inside of the projector. You may feel hot, but this is 
not a malfunction. 
•  Check that the volume isn't set to low. 
•  The microcomputers inside the projector may be wrongly operating because of noise. 
  Press the POWER button to turn off the lamp and unplug the power cord from the 
wall outlet. Wait about 10 minutes, plug the power cord in, and try again.
•  This indication appears when the ambient temperature rises high. When the ambient 
temperature stays high, the lamp goes out.
  Eliminate any causes of the rise in the ambient temperature.
•  This indication appears when the air inlet or outlet grille is blocked. When they are kept 
blocked, the lamp goes out. 
  Remove the objects blocking the air inlet or outlet grille. 
•  This mark appears when ineffective operation is carried out. This isn't a product 
malfunction. 
•  Check that the batteries are loaded in the remote control or the batteries are not weak. 
(See page 6.)
•  Check that the remote control sensor isn't exposed to direct sunlight or fl uorescent 
light. (See page 9.)
•  Use the remote control within its operation range. (See page 9.)
•  Use the remote control at least 10 cm away from the projector. 
• PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS to en-
able the password lock. 
 
Cancel the password lock or contact the person in charge of management of the 
projector. (See page 28.)
•  Because the color wheel spins at a high speed, metallic sounds may be heard in rare 
occasions. Such symptom is not a malfunction.
If the following problem occurs after the lamp is replaced, check the following  rst. 
Problem
The projector does not 
turn on. 
The STATUS indicator 
blinks.Solution
•  Fit the lamp cover securely. (See pages 31 and 32.)  
•  Reset the lamp operating time. (See page 32.)
•  Reset the lamp operating time. (See page 32.)
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. 
Refer to the information that came with the Kensington System for instructions on how to use it to secure the 
projector. Please contact Kensington Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone : +1- (650)572-2700  Fax : +1- (650)572-9675 
						

							EN-36
Indicators
POWER
Steady 
green
or
Steady red
Steady red
Steady 
green
Steady red
Steady red
Blinking 
green/red
Blinking 
green/red
STATUS
Blinking orange
Blinking green
Blinking green/red
Blinking red
Steady red
Off
Steady
or
Blinking
CONDITION
Abnormal temperature
• The ventilation grilles are clogged with dust or dirt.
• The room temperature is high.
The protection circuit is working or the lamp is in an
abnormal condition. 
Lamp operation time warning. (Total lamp operation time 
reached 3750 hours
*1 while the power was on.)
Lamp operation time wa rning. (
Total lamp operation time 
reached 3750 hours
*1 while the power was off.)
Lamp operation time warning. (Total lamp operation time 
reached 5000 hours
*1 *2 while the power was off.)
The lamp cover isn’t closed. 
Abnormal.POSSIBLE SOLUTION
•  Clean the ventilation grilles.
•  Relocate the projector to a cooler place.
•  Wait until the STATUS indicator goes out, 
then press the POWER button.
•  If the above solution is not effective, 
replace the lamp.
Replace the lamp.
Change with a new lamp if this problem 
recurs.
Close the cover correctly.
Contact your dealer.
*
1 Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be 
    shorted.
*
2 Duration when LAMP MODE is set to STANDARD, this duration will be shorted up to 2000 hours.
This projector has 2 indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these problems persist, turn the projector off and consult your 
dealer. 
Normal condition
Abnormal condition
POWER indicator
STATUS indicator 
POWER
Steady 
red
Steady
green
Steady
green
STATUS
Off
Blinking 
green
Steady 
green
CONDITION
Stand-by
Lamp stand-by (about 1 minute)
The power is on. (Normal condition)
NOTE
The POWER button cannot be used to
switch between on and off. 
						

							EN-37
ENGLISH
Speci cations
The specifi cations and outside appearance of the projector are subject to change without prior notice.
*1 : Wireless LAN unit isn’t packaged together with the projector.
Replacement part
(Option / Not included in the box)
Spare lamp                (VLT-XD400LP)
Type  
Model 
Display Technology
 
Projection lens 
Light-source lamp 
Image size (Projection distance)
Maximum  
resolution Computer signal
 
Video signal 
Component  
signal
 
Computer input   
Video input
Audio input
Speaker
Control terminal/Others
Operating temperatures
Rated voltage
Power consumption 
Dimensions  
Weight
Others  S-video input
Video input
Component video 
input
Analog input
Digital input (DVI)
Audio input
DC OUTDLP™ projector
XD490U/XD460U
0.7-inch Single chip DMD
Pixel 1024 x 768 = 786432 pixels
F 2.4 - 2.6  f= 23 - 27.6 mm
250 W
40" min. to 300" max. (Projection distance 1.3 to 10 m)
Maximum resolution : 1280 x 1024 dots (Analog) / compressed
Panel resolution : 1024 x 768 dots
NTSC / PAL / SECAM / NTSC 4.43 / PAL-M / PAL-N / PAL-60 
480i, 480p, 576i, 576p, 720p, 1080i
Panel resolution : 1024 x 768 dots
[Signal type]  [Terminal type]  [Line]
Analog RGB  D-SUB 15P  1
Digital RGB  DVI  1
[Signal type]  [Terminal type]  [Line]
Video input  RCA  1 
S-Video input  S  1
Component video input RCA  1
[Signal type]  [Terminal type]  [Line]
RGB  Stereo mini jack (ø3.5) 1 
Component  RCA (L, R)  1
Video/S-video  RCA (L, R)  1
2 W Mono Round type ø4.5 cm 
x 1
RS-232C (8-pin), USB terminal
+41°F (+5°C) to +95°F (+35°C)   
AC100 - 240 V, 50/60 Hz
3.5 A
310 mm (W) x 100 mm (H) x 245 mm (D)       * Not including protrusion.
2.9 kg
Luminance signal : Vp-p=1.0 V 75 Ω (negative sync)
Chrominance signals : Vp-p=0.286 V 75 Ω (burst signal)
Vp-p=1.0 V  75 Ω (negative sync)
YC
BCR : Vp-p=1.0 V 75 Ω (Y)  (negative sync)  
Vp-p=0.7 V 75 Ω (C
B, CR) 
RGB : Vp-p=0.7 V 75 Ω (negative sync)  
YC
BCR : Vp-p=1.0 V (Y)  (negative sync)  Vp-p=0.7 V (CB, CR) 
HD/CS : TTL-level (negative or positive polarity)
VD : TTL-level (negative or positive polarity)
DVI-D interface (TMDS single link) with HDCP
350 mVrms,  10 kΩ or more 
5 V 1.5 A(max) (For wireless LAN unit 
*1) 
						

							EN-38
 TV60, 480i(525i) -  15.73  59.94  1024 x 768  -  *1, *3
  TV50, 576i(625i)  -  15.63  50.00  1024 x 768  -  *1, *3
  1080i 60 (1125i 60)  -  33.75  60.00  1024 x 576  -  *1, *2
  1080i 50 (1125i 50)  -  28.13  50.00  1024 x 576  -  *1
  1080i 50a (1250i 50)  -  31.25  50.00  1024 x 576  -  *1
  480p (525p)  -  31.47  59.94  1024 x 768  -  *1, *2
  576p (625p)  -  31.25  50.00  1024 x 768  -  *1, *2
  720p 60 (750p 60)  -  45.00  60.00  1024 x 576  -  *1, *2
  720p 50 (750p 50)  -  37.50  50.00  1024 x 576  -  *1
  PC98  640 x 400  24.82  56.42  1024 x 640  640 x 400  *1
  CGA70  640 x 400  31.47  70.09  1024 x 640  640 x 400 
  CGA84  640 x 400  37.86  84.13  1024 x 640  640 x 400 
  CGA85  640 x 400  37.86  85.08  1024 x 640  640 x 400 
  VGA60  640 x 480  31.47  59.94  1024 x 768  640 x 480  *2
  VGA72  640 x 480  37.86  72.81  1024 x 768  640 x 480 
  VGA75  640 x 480  37.50  75.00  1024 x 768  640 x 480 
  VGA85  640 x 480  43.27  85.01  1024 x 768  640 x 480 
  SVGA56  800 x 600  35.16  56.25  1024 x 768  800 x 600
  SVGA60  800 x 600  37.88  60.32  1024 x 768  800 x 600  *2
  SVGA72  800 x 600  48.08  72.19  1024 x 768  800 x 600
  SVGA75  800 x 600  46.88  75.00  1024 x 768  800 x 600
  SVGA85  800 x 600  53.67  85.06  1024 x 768  800 x 600
  SVGA95  800 x 600  59.97  94.89  1024 x 768  800 x 600  *1
  XGA43i  1024 x 768  35.52  86.96  1024 x 768  1024 x 768  *1
  XGA60  1024 x 768  48.36  60.00  1024 x 768  1024 x 768  *2
  XGA70  1024 x 768  56.48  70.07  1024 x 768  1024 x 768
  XGA75  1024 x 768  60.02  75.03  1024 x 768  1024 x 768
  XGA85  1024 x 768  68.68  85.00  1024 x 768  1024 x 768
  SXGA70a  1152 x 864  63.85  70.01  1024 x 768  1024 x 768 
  SXGA75a  1152 x 864  67.50  75.00  1024 x 768  1024 x 768 
  SXGA85a  1152 x 864  77.49  85.06  1024 x 768  1024 x 768 
  SXGA60b  1280 x 960  60.00  60.00  1024 x 768  1024 x 768 
  SXGA75b  1280 x 960  75.00  75.00  1024 x 768  1024 x 768 
  SXGA43i  1280 x 1024  46.43  86.87  960 x 768  1024 x 768  *1
  SXGA60  1280 x 1024  63.98  60.02  960 x 768  1024 x 768  *2
  SXGA75  1280 x 1024  79.98  75.02  960 x 768  1024 x 768 
  MAC13  640 x 480  35.00  66.67  1024 x 768  640 x 480 
  MAC16  832 x 624  49.72  74.55  1024 x 768  832 x 624 
  MAC19  1024 x 768  60.24  75.02  1024 x 768  1024 x 768 
  HP75  1024 x 768  62.94  74.92  1024 x 768  1024 x 768 
  HP72  1280 x 1024  78.13  72.00  960 x 768  1024 x 768 
  SUN66a  1152 x 900  61.85  66.00  984 x 768  1024 x 768 
  SUN76a  1152 x 900  71.81  76.64  984 x 768  1024 x 768 
  SUN66  1280 x 1024  71.68  66.68  960 x 768  1024 x 768 
  SUN76  1280 x 1024  81.13  76.11  960 x 768  1024 x 768 
  SGI72  1280 x 1024  76.92  72.30  960 x 768  1024 x 768 
  SGI76  1280 x 1024  82.01  76.00  960 x 768  1024 x 768 
Speci cation of RGB signals in each computer mode of the projector 
  Signal mode  resolution  horizontal  Vertical  Normal mode  Real mode
     (H x V)  frequency (kHz)  frequency (Hz)  (H x V)   (H x V)
*1 :  The EXPAND mode and the PinP mode doesn't 
function with this signal.
*2 :  Available with the signal for DVI-D terminal.
*3 : 
Available only when the input signal is YCBCR.
•  When ASPECT in the FEATURE menu is set to 
REAL, images are displayed in their original size. In 
the REAL mode, images are black-framed when the 
image resolution is lower than 1024 x 768.
Important:
•  Some computers aren't compatible with the projec-
tor.
•  The projector's maximum resolution is 1024 x 768 
pixels.  It may not display images of higher resolu-
tions than 1024 x 768 correctly.
•  Images with SYNC on G (Green) signal may jitter.
•  Images with SYNC on G (Green) signal may be 
tinged with green.•  If the resolution and frequency of your computer 
aren't shown on the table, fi nd the compatible reso-
lution and frequency by changing the resolution of 
your computer. 
•  Set COMPUTER INPUT in the SIGNAL menu to RGB 
when inputting the HDTV signal as RGB signal.
•  In the case of SXGA, the right side of the image may 
not appear. In this case, adjust TRACKING in the 
SIGNAL menu.
•  TV60 and TV50 are equivalent to 480i and 576i 
respectively. When these signals are supplied to the 
VIDEO or S-VIDEO signal, the signal mode is indicat-
ed as TV60 or TV50. When they are supplied to the 
COMPONENT terminal, the signal mode is indicated 
as 480i or 576i. 
•  Video signals having resolution exceeding the 
maximum resolution supported by this projector are 
reduced to the maximum resolution size of the pro-
jector even in the REAL mode. 
•  This projector doesn’t support 480i, 576i, and 480p 
signals from video devices having 5 lines (R, G, B, H, V). 
Speci cations  (continued) 
						

							EN-39
ENGLISH
 1  R(RED)/CR 2 G(GREEN)/Y
 3 B(BLUE)/CB
 4  GND
  5  GND   
  6  GND   
 7  GND
  8  GND    
 9  DDC 5V
 10  GND 
 11  GND 
 12  DDC Data
 13  HD/CS
 14  VD
 15  DDC Clock  1  TXD  IN
 2 
- - 
 3 - -  4  GND   - 
 5 - - 6 - - 7  RXD  OUT 
 8 - -
1
352
681 5
116 10
15SERIAL (8-pin)
  Pin No.  Name  I/O
COMPUTER IN / COMPONENT VIDEO IN
(Mini D-SUB 15-pin)
 Pin No.  Spec.
DVI-D (HDCP)
(DVI-D 24-pin)
 PIN No. SPEC PIN No. SPEC
 1  DATA 2-  13 - 2  DATA 2+ 14 +5V Power
  3  DATA 2 Shield 15 Ground
 4 -  16  Hot Plug Detect
 5 - 17 DATA 0-
  6  DDC Clock     18  DATA 0+
  7  DDC Data  19  DATA 0 Shield
 8 
- 20 - 9  DATA 1-  21 - 10  DATA 1+  22  Clock Shield
  11  DATA 1 Shield   23  Clock+
 12 
- 24 Clock-
1724
169
8
1
Connectors
61
245
310
100 5
Dimension Drawings (unit : mm) 
						

							MITSUBISHI Projector Contact Information
Manufactured by Mitsubishi Electric Corporation
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
MITSUBISHI ELECTRIC CORPORATION
North America
MESCA (Mitsubishi Electric Sales Canada Inc.)
http://www.mitsubishielectric.ca
Information Technologies Group, 4299 14th Avenue, 
Markham, Ontario L3R 0J2, Canada
Sales & Technical Inquires
 Phone :+1-(800) 450-6487
 Fax :+1-(905) 475-7958
 E-mail :[email protected]
Customer Care
 E-mail :[email protected]
MDEA (Mitsubishi Digital Electronics America, Inc.)
(Warranty Registration)
http://www.mitsubishi-presentations.com/
Presentation Products Division, 9351 Jeronimo Road, 
Irvine, CA 92618 U.S.A
Sales & Inquires
 Phone :+1(888) 307-0349  or  +1(949)465-6000
 E-mail :[email protected]
Technical Inquires 
 Phone :+1-(888) 307-0309 
 E-mail :[email protected]  
    
Europe
MEU-FRA (Mitsubishi Electric Europe B.V French Branch)
25, Boulevard des Bouvets 92 741, Nanterre CEDEX, 
France
Sales Inquiries   
 Phone :+33 (0)1 55-68-55-53
 Fax :+33 (0)1 55-68-57-31
Techinical Inquireis   
 Phone :+33 (0)1 55-68-56-42 
 Fax :+33 (0)1 55-68-57-31 
MEU-GER (Mitsubishi Electric Europe B.V. German Branch)
http://www.mitsubishi-evs.de/
Gothaer Strasse 8, 40880 Ratingen, Germany
Sales Inquires   
  Phone  :0049 - 2102 - 486 9250 
  Fax  :0049 - 2102 - 486 7320 
Techinical Inquires   
  Phone  :0049 - 2102 - 486 1330   
  Fax  :0049 - 2102 - 486 1340 
MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch)
http://www.mitsubishi.ie/
Westgate Business Park, Ballymount, Dublin 24, Ireland
Sales Inquiries   
 Phone :+353-1-4198807 
 Fax :+353-1-4198890 
Technical Inqiries   
 Phone :+353-1-4198808 
 Fax :+353-1-4198895 
MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch)
Centro Direzionale Colleoni, Palazzo Persero-Ingresso 2, 
Via Paracelso 12, 20041 Agrate Brianza, Italy
Sales & Technical Inquiries  
 Phone :+39-(0)39-60531 
 Fax :+39-(0)39-6053214 
 E-mail :[email protected] 
MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch)
http://www.mitsubishi.nl/LCD/ProdFrame.html
Nijverheidsweg 23A, 3641 RP Mijdrecht, The Netherlands 
Sales Inquiries   
 Phone :+31-297-282461 
 Fax :+31-297-283936 
 E-mail :[email protected] 
Techinical Inquiries   
 Phone :+31-297-282461 
 Fax :+31-297-283936 
 E-mail :[email protected] 
Russia (Mitsubishi Electric Europe B.V Moscow 
Representative Offi ce)
http://www.mitsubishi-projector.ru/
Moscow Representative Offi ce, 52/5 Kosmodamianskaya 
Nab., 115054, Moscow, Russia
Sales & Techinical Inquiries   
 Phone :(7095) 721-2068 
 Fax :(7095) 721-2071 MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch)
http://www.mitsubishielectric.es/
Ctra. de Rubi, 76-80, 08173 Sant Cugat del Valles, 
Barcelona, Spain
Sales Inquiries   
 Phone :+34-93.565.31.54 
 Fax :+34-93.589.43.88 
 E-mail :[email protected]
Technical Inquiries   
 Phone :+34-93.586.27.51 
 Fax :+34-93.588.53.87 
 E-mail :[email protected]
MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian 
Branch)
Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden
Sales Inquiries   
 Phone :+46-(0)8-6251070 
 Fax :+46-(0)8-6251036 
Technical Inquiries   
 Phone :+46-(0)8-6251052 
 Fax :+46-(0)8-6251036 
MEU-UK (Mitsubishi Electric Europe)
http://www.mitsubishi.co.uk/evs/
Visual Information Systems Division, Travellers Lane, 
Hatfi eld, Hertfordshire, AL10 8XB U.K.   
Sales Inqiries   
 Phone :+44 (1707) 278684 
 Fax :+44 (1707) 278541 
 E-mail :[email protected] 
Technical Inquiries   
  Phone  :+44 (870) 606 5008 
 Fax :+44 (1506) 431927 
 E-mail :[email protected] 
Asia
CHINA (Mitsubishi Electric Air-Conditioning & Visual 
Information Systems (Shanghai) Ltd.)     
26/F .,Oriental Center ,699 Nanjing Rd(W),Shanghai, 
200041,China 
Sales Inquiries     
 Phone :+86(21) 5211-0882-3010 
 Fax :+86(21) 5211-0576
Technical Inquiries     
 Phone :+86(21) 5211-0882-3018  
 Fax :+86(21) 5211-0576 
HONG KONG (Mitsubishi Electric Ryoden Air-Conditioning 
& Visual Information Systems (HongKong) Ltd.) 
7th Floor, Manulife Tower, 169 Electric Road, North Point, 
Hong Kong   
Sales Inquiries   
 Phone :+852-2510-1505 
 Fax :+852-2510-0463 
Technical Inquiries   
 Phone :+852-2422-0161 
 Fax :+852-2487-0181 
SINGAPORE (Mitsubishi Electric Asia Pte. Ltd.) 
http://www.mitsubishielectric.com.sg
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943
Sales Inquiries   
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 
INDIA (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943
Sales Inquiries   
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 INDONESIA (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943
Sales Inqiries   
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 
PHILLIPINES (Mitsubishi Electric Asia Pte. Ltd.) 
http://www.mitsubishielectric.com.sg
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943
Sales Inquiries   
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inqiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 
VIETNAM (Mitsubishi Electric Asia Pte. Ltd.) 
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943 
Sales Inquiries
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 
STC (Setsuyo Astec Corporation Seoul Branch) 
4F,Dongseo Game Channel Bldg,660-11 Deungchon-Dong, 
Kangseo-Ku, Seoul, Korea  
Sales & Technical Inqiries   
 Phone :+82-(0)2-2657-9841~3 
 Fax :+82-(0)2-2657-9900 
MALAYSIA (Antah Melco Sales & Services Sdn. Bhd.)
6, Jalan 13/6 46860 Petaling Jaya Selangor, Darul Ehsan, 
Malaysia 
Sales & Technical Inquiries  
  Phone  :+60-(0)3-79552088  (Ext. 203) 
 Fax :+60-(0)3-79563950/+60-(0)3-79582576
Technical & Service Inquiries   
 Phone :+60-(0)3-79552088 (Ext. 106) 
 Fax :+60-(0)3-79563950/+60-(0)3-79582576
ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.)
http://www.mitsubishi-kyw.co.th/
11TH FL., 88 SEC. 6, CHUNG SHAN N. RD., TAIPEI, 111R.
O.C.
Sales & Technical Inquires     
 Phone :+886-2-2832-8255
 Fax :+886-2-2833-9813 
MKY (Mitsubishi Electric Kang Yong Watana Co., Ltd. )
http://www.mitsubishi-kyw.co.th/
Road, Huamark Bangkapi, Bangkok 10240, Thailand 
Sales & Technical Inquiries  
 Phone :+66-2-731-6841 
 Fax :+66-2-379-4763 
Oceania
ME-AUST (Mitsubishi Electric Australia)
http://www.mitsubishi-electric.com.au/prod.asp?prod=proj
348 Victoria Road, Rydalmere, N.S.W. 2116, Australia Sales 
& Technical Inqiries     
 Phone :+(612)9684-7777
 Fax :+(612)9684-7208 
 E-mail :[email protected]
Technical Inquiries   
 Phone :+(612)9684-7694 
 Fax :+(612)9684-7684 
 E-mail :[email protected] 
BDT (Black Diamond Technologies Ltd.)
(Warranty Registration)  http://www.bdt.co.nz/projectors/
warranty.asp
1 Parliament St, Lower Hutt, Wellington, New Zealand Sales 
Inquiries  
 Phone :+64-(0)4-560-9100 
 Fax :+64-(0)4-560-9133 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+64-(0)4-560-9100 
 Fax :+64-(0)4-560-9133 
 E-mail :[email protected]