Mitsubishi Xd221u Data Projector User Manual

							EN-11
ENGLISH
Basic connections (continued)
Projector + Computer 
For computer with Mini D-SUB  
For analog connection: 
1. Connect one end of the supplied RGB cable to the COMPUTER IN terminal (1, 2) of the projector.
2. Connect the other end of the RGB cable to the monitor port of the computer. 
For monitor connection:Connect the RGB cable from the monitor to the MONITOR OUT terminal of the projector.
 Images may not be displayed correctly depending on the type of the input signal. See the instruction manual of the monitor.
 Signals are coming from the COMPUTER IN terminal (1 or 2) of the projector.
 When STANDBY MODE is set to LOW, MONITOR OUT is not output during the STANDBY state. 
 When STANDBY MODE is set to STANDARD, the signals from COMPUTER IN-1 are output during the STANDBY state.
 When signals are coming from both COMPUTER IN terminals (1, 2), images are projected from the terminal (1 or 2) currently or last selected in 
the projectors menu.
Important:  When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
 Some computers require additional connectors or analog RGB output adapters to be connected with this projector. Contact your dealer for fur-
ther information. 
 This projector uses stereo mini jack for its audio input. Check the type of the audio output terminal of the connected computer and prepare a 
proper cable for connection. Some computers don’t have the audio output terminal. 
 Speaker output is mono. 
 When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted. 
For Macintosh  If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further information. 
 Some Macintoshes require a MAC adapter for the RGB cable for connection with this projector. Contact your dealer for further information. 
About DDCThe COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC 1/2B standard. When a computer supporting this 
standard is connected to this terminal, the computer will automatically load the information from this projector and prepare for output of appropriate 
images.
 After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the wall outlet first, and then boot up 
the computer.
COMPUTER INRGB cable for PC
AUDIO
 OUT
Audio cable (option) MONITOR OUT
Necessary when outputting to both 
a PC monitor and the projector.PC audio cable (option) AUDIO
 IN
to PC audio outputComputer
to monitor port
RGB cable for PC (option) 
						

							EN-12
Preparation
Preparation for projection 1. Attach the provided power cord to the projector. 
2. Plug the power cord in the wall outlet. 
Warning:  Do not look into the lens directly when the projector is on. 
 One of power cords for the U.S., Europe and U.K. is provided 
appropriately.
 This projector uses the power plug of three-pin grounding type. Do 
not remove the grounding pin from the power plug. If the power 
plug doesn’t fit your wall outlet, ask an electrician to change the 
wall outlet. 
 In case that the power cord for the U.S is provided with this projec-
tor, never connect this cord to any outlet or power supply using 
other voltages or frequencies than rated. If you want to use a 
power supply using other voltage than rated, prepare an appropri-
ate power cord separately.
 Use 100-240 V AC 50/60 Hz to prevent fire or electric shock. 
 Do not place any objects on the power cord or do not place the 
projector near heat sources to prevent damage to the power cord. 
If the power cord should be damaged, contact your dealer for 
replacement because it may cause fire or electric shock. 
 Do not modify or alter the power cord. If the power cord is modified 
or altered, it may cause fire or electric shock. 
Caution:  Plug in the power cord firmly. When unplugging, hold and pull the 
power plug, not the power cord. 
 Do not plug in or out the power cord with your hand wet. It may 
cause electric shock. 
Adjustment of the projection angle For the best projection, project images on a flat screen installed at 90 
degrees to the floor. If necessary, tilt the projector using the two 
adjustment feet on the bottom of the projector.
Using the adjustment feet (front)1. Tilt up the projector to the appropriate angle. 
2. Rotate the adjustment feet (front) for fine adjustment. 
Important:  Install the screen on a flat wall at 90 degrees to the floor. 
 Slanting the projector more than ±10° (right and left) or ±15° (front 
and rear) may cause trouble or explosion of the lamp. You can tilt 
the projector up to 8 degrees using the adjustment feet only. 
 Images may not be projected in a shape of a regular rectangle or 
with its aspect ratio 4:3, depending on the installation conditions of 
the projector and the screen. 
 To correct vertical keystone distortion, press the KEYSTONE but-
ton on the remote control to display KEYSTONE, and adjust the 
image by pressing the VOLUME S, T button. 
In the following cases:  
Important: 
 When the keystone adjustment is carried out, the adjustment 
value is indicated. Note that this value doesn’t mean a projection 
angle. 
 The allowable range of the adjustment value in the keystone 
adjustment varies depending on the installation conditions. 
 When the keystone adjustment takes effect, the resolution 
decreases. In addition, stripes may appear or straight lines may 
bend in images with complicated patterns. They are not due to 
product malfunctions. 
 Noise may appear on the screen during the keystone adjustment 
because of the type of the video signal being projected and the 
setting values of the keystone adjustment. In such cases, set the 
keystone adjustment values in the range where the image is dis-
played without noise. 
 When the keystone adjustment is carried out, the image may not 
be displayed correctly because of the type of input signal.
Press the T  
button.Press the S  
button. 
						

							EN-13
ENGLISH
Basic operation
Power-on 1. Turn on the device connected to the projector first. 
2. Plug the power cord in the wall outlet. 
 The POWER indicator lights up. 
 If the power cord is unplugged from the wall outlet before the 
projector is cooled down completely after use, the fans may 
start rotating when the power cord is plugged in next time 
and the POWER button may not function. In this case, wait 
for the fans to stop and press the POWER button to light the 
indicator. 
3. Press the POWER button on the control panel or the ON button 
on the remote control. 
 It may take about one minute for the lamp to light up. 
 The lamp occasionally fails to light up. Wait a few minutes 
and try to light the lamp again. 
 After the POWER button is pressed, the image may flicker 
before the lamp becomes stable. This is not a product mal-
function. 
 Regardless of the setting of LAMP MODE in the INSTALLA-
TION menu, the STANDARD lamp mode is activated by 
default whenever the projector is turned on. The LAMP 
MODE is set to either STANDARD or LOW depending on the 
setting last selected, and you cannot switch the LAMP 
MODE in about one minute after the lamp is on.
Important:  If the lamp exceptionally turned off due to the power interruption or 
voltage drop, it can happen that the lamp does not turn on even if 
you switch again the power supply on. In that case, please pull the 
electric cord out of the consent and put it again in the consent 
about 10 minutes later.
 The projector starts warming up when the POWER button is 
pressed. During the warm-up process, images may appear dark 
and no commands are accepted.  By blinking red, the STATUS indicator indicates that the lamp 
should be replaced soon. Replace the lamp when the STATUS 
indicator blinks red. (See page 29 and 32.) 
 Images may not be projected with good quality in an extremely hot 
or cold environment. (This is not a product malfunction.) 
 In order to ensure the safety in case of trouble with the projector, 
use an electrical outlet having an earth leakage breaker to supply 
the power to the projector. If you do not have such outlet, ask your 
dealer to install it.
4. Adjust the focus by turning the focus ring. 
5. Choose your desired external input source using the SOURCE 
or COMPUTER or VIDEO button.
 Each press of SOURCE button of the Control Panel enables 
the input source to switch in the following order: COMPUTER 
1, COMPUTER 2, VIDEO, and S-VIDEO.
 When pressing COMPUTER (1 or 2), VIDEO, or S-VIDEO 
button on the remote control, the input source switches 
directly as the button pressed. 
 The projector automatically selects the appropriate signal 
format. The selected signal format is displayed on the 
screen. 
 The SOURCE, COMPUTER and VIDEO buttons don’t func-
tion while the menu is being displayed. 
 When COMPUTER is chosen as the source, images sup-
plied from the computer may flicker. Press the W or X button 
on the remote control to reduce flicker, if it occurs. 
 To avoid permanently imprinting a fixed image onto your pro-
jector, please do not display the same stationary images for 
long period.
6. Adjust the image size by turning the zoom ring.
 If necessary, adjust the focus and zoom again.When fine streaks are seen on projected imagesThis is due to interference with the screen surface and is not a mal-
function. Replace the screen or displace the focus a little.
STANDBY ON
ASPECT MAGNIFY
KEYSTONEVO L PA G E
UP
DOWN
MENU
FREEZE AU T O
POSITION
AV
MUTEENTER
1
2COMPUTERVIDEOVIEWER
UNPLUGS-
VIDEO
WIRELESS DVI
4  FOCUS
6  ZOOM
5
3, 1, 25 1, 2 3
Indicator
ConditionSTATUS POWER
Stand-by - Red
When the lamp is on. Green Green 
						

							EN-14
Basic operation (continued)
Power-off Use the following procedure to turn off the projector.
The lamp may deteriorate if the projector is powered off and on 
repeatedly within 30 minutes after the lamp is lighted.
1.Press the POWER button on the control panel or the STANDBY 
button on the remote control. 
 The message POWER OFF? YES : PRESS AGAIN 
appears on the screen.
 To cancel, press any button except the POWER button. 
(Some buttons on the remote control don’t function for can-
cel.) 
2.Press the POWER button on the control panel or the STANDBY 
button on the remote control within 10 seconds again. 
 The lamp will go out and the STATUS indicator will start 
blinking. 
 Though the lamp goes out at this second press of the 
POWER button (or STANDBY button), the air outlet fans con-
tinue operating for one minute to cool down the lamp. The 
STATUS indicator will stop blinking. 
 After stopping the air outlet fans, if the temperature inside the 
set is still high, the temperature sensor detects it and then 
the air outlet fans may start again.
3.Unplug the power cord. 
 The POWER indicator will go out. 
 If the power cord should be unplugged accidentally while 
either the air inlet fan or the air outlet fans are operating or 
the lamp is on, allow the projector to cool down for 10 min-
utes with the power off. To light the lamp again, press the 
POWER button (or ON button). If the lamp doesn’t light up 
immediately, repeat pressing the POWER button (or ON but-
ton) two or three times. If it should still fail to light up, replace 
the lamp. 
Notice: When storing the projector in the carrying case, the lens should 
face up.
Instant Shut DownYou dont have to wait for the cooling fan to cease operation after pow-
ering off the projector. You can unplug the power cord right after the 
projector is powered off.
 Dont shut down the projector while the STATUS indicator is blink-
ing after the lamp lights up because the lamps life may be short-
ened.
 Dont turn the projector back on right after shutting it down 
because the lamps life may be shortened. (Wait about 10 minutes 
before turning the projector back on.)
 Before shutting down the projector, be sure to close the menu 
screen. If you shut down the projector without closing the menu, 
the setting data of the menu may not be saved.
AUTO POSITION button When the image isn’t projected in the right position with COMPUTER 
selected as the input source, follow the procedure below. 
1. Project a bright image such as the Recycle Bin window on the 
full screen. 
2. If the screen saver is running, turn it off. 
3. Press the AUTO POSITION button. 
 If the image is still not in the right position, adjust the image 
position using the SIGNAL menu. See page 22. 
Volume from the speaker Press the VOLUME S or T button to change the volume 
from the speaker.
The volume control bar will appear on the screen.
 The volume control bar will disappear about 10 seconds after the 
VOLUME button is released. 
 The VOLUME buttons don’t function while the menu selection bar 
or the menu is being displayed. 
 When a high-level audio signal, such as a DVD audio signal, is 
supplied to the AUDIO IN terminal, the output from the speaker 
may be distorted. 
AV  m u t e  The video and audio signals are temporarily muted when the AV 
MUTE button is pressed. To cancel muting, press the AV MUTE button 
again. 
Setting the aspect ratioYou can change the aspect ratio of the input video signal (or the ratio 
of width to height of the image). Change the setting according to the 
type of the input video signal.
How to change the settings:
With the remote control:
1. Press the ASPECT button.
 Every time the ASPECT button is pressed, the aspect mode 
changes from NORMAL to 16:9, to FULL, and back to NOR-
MAL.
With the FEATURE menu:(See page 21 for menu setting.)
1. Display the FEATURE menu.
2. Select ASPECT by pressing the S or T button.
3. Select your desired aspect ratio by pressing the W or X button.
When 16:9  is selected.
4. Press the ENTER button.
5. Select your desired position (CENTER, UPPER or LOWER) by 
pressing the W or X button.
To cancel the menu:
6. Press the MENU button.
Important: When a 16:9 image is kept displayed for a long time before dis-
playing 4:3 image, the afterimages of the black bars may appear 
on the 4:3 image screen. Consult your dealer in this case.
Caution:  After using the projector, wait one minute for the air outlet fans to 
stop in normal use. Then unplug the power cord from the wall out-
let. 
 The lamp can’t be lit again for one minute after turned off for safety 
purpose. It will take another one minute for the STATUS indicator 
to go out. If you want to turn on the projector again, wait until the 
indicator goes out, and then press the POWER button. 
 The air outlet fans rotate faster as the temperature around the pro-
jector rises. 
 When the temperature around the projector rises high, the sign 
TEMPERATURE!! blinks red on the screen. If the temperature 
stays high, the lamp will go out automatically. 
Important:  Do not display a still picture for a long time because the afterim-
ages may persist on the screen.
VOLUME     10
FEATURENORMAL
opt.
ASPECT 
						

							EN-15
ENGLISH
Basic operation (continued)
Wall ScreenThis function is to reproduce natural color tones when images are pro-
jected directly onto a screen or wall surface. You can select from 
BEIGE, LIGHT BLUE, LIGHT GREEN, PINK, BLACK BOARD, WHITE 
BOARD, and OFF, to match the color of the screen or wall to be used 
for projection.
1. Display the INSTALLATION menu. (See page 20 for more details.)
2. Press the S or T button to select WALL SCREEN.
3. Press the W or X button to select the color closest to that of the 
screen on which images are projected.
 When the GAMMA mode setting is changed, images may not 
be displayed correctly.
 When OFF or BLACK BOARD/WHITE BOARD is selected, 
the density cannot be adjusted.
 When WHITE BOARD is selected, BrilliantColor
TM in the 
Color Enhancer menu of the Image menu cannot be used. 
Additionally, Theater in the Color Enhancer menu of the 
Image menu has no effect and is automatically canceled 
when WHITE BOARD is selected.
4. Press the ENTER button.
5. Press the W or X button to adjust the density of the selected 
color.
When connecting to a laptop computer:When this projector is connected to a laptop computer, there may be 
times when images may not be projected. When it occurs, set the 
computer so that it can output signals externally. The procedure varies 
across computers in use. See the instruction manual of your com-
puter.
INSTALLATION
opt.
WALL SCREEN
LAMP MODEBEIGE
STANDARD
LIGHT BLUE 1 
						

							EN-16
Menu operation
As one of the two types of MENU display, following QUICK MENU appears on the screen when pressing MENU button on the remote control. In 
addition, DETAIL MENU (See page 18) appears when selecting DETAIL MENU in this MENU and pressing ENTER button.
 Comparing QUICK MENU with DETAIL MENU, if the contents in those two menus are same each other, the functions in those two menus are 
same as well.
 To close QUICK MENU or DETAIL MENU, press MENU button when MENU is displayed.
QUICK MENU* Menus are not displayed when no signal is supplied to the projector.
QUICK MENU Basic operationSeveral settings can be adjusted using the menu.
Example : Contrast setting
1. Press the MENU button.
2. Press the ENTER button (or T button).3. Press the S or T button to select CONTRAST.
4. Press the W or X button to adjust the contrast.
5. Exit the menu by pressing the MENU button several times.
Important:  When the button doesn’t function, unplug the power cord from the 
wall outlet. Wait about 10 minutes, plug the power cord in, and try 
again.
 After selecting the items marked with  , press the ENTER but-
ton.
QUICK MENUCOLOR ENHANCER
CONTRASTBRIGHTNESS
COLOR TEMP.
AUTO
THEATERUSER
PRESENTATIONSTANDARD
±30STANDARD
SHARPNESS *1
±5
LAMP MODE
 ASPECT
USER MENU
SELECT USER MENU
STANDARD, LOW
COLOR
LOWHIGHUSER
INFORMATION
SYNC. TYPE *2
LAMP TIME (LOW)INPUTRESOLUTIONVERTICAL FREQUENCY
HORIZONTAL FREQUENCY
±30
WALL SCREEN
TINTCLOSED CAPTION
AUDIO INPUTIMAGE REVERSEMENU POSITIONCINEMA MODEWXGALANGUAGE
STANDBY MODE
NORMAL, 16:9, FULL 
DETAIL MENU
OK
*1 Not available with certain signals
*2 Not available when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
QUICK MENU
QUICK MENU
AUTOCOLOR
ENHANCER
0CONTRAST
+10CONTRAST 
						

							EN-17
ENGLISH
Menu operation (continued)
Menu OptionsSet the following options provided in the respective menus.
1. QUICK MENU
 You cannot adjust COLOR TEMP. when WALL SCREEN is set to other than OFF.
 When COLOR ENHANCER is switched, projected images may be distorted.
 By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, 
and you cannot switch the LAMP MODE in about one minute after the lamp is on.
2. INFORMATION menu
Menu option Setting Feature description
COLOR ENHANCERAU TOAutomatically sets an optimal color balance based on the input signal. 
Use this setting for most cases.
PRESENTATION Makes projected images bright and crisp.
STANDARD Makes projected images look natural.
THEATER Makes projected images soft and smooth. Best suited for movies.
USER Reflected by the value set in IMAGE menu. (See page 23.)
CONTRAST±30 Adjusts the contrast of projected images. (See page 23.)
BRIGHTNESS±30 Adjusts the brightness of projected images. (See page 23.)
COLOR TEMP. 4 optionsAdjusts the color temperature. You cannot select this setting when 
WALL SCREEN in the INSTALLATION menu is set to a setting other 
than OFF. (See page 23.)
SHARPNESS±5 Adjusts the sharpness of projected images. (See page 23.)
LAMP MODESTANDARD Select this setting when you want to view images in a well-lit room.
LOWSelect this setting when you want to view images at a moderate light 
intensity. The operating sound is consequently reduced, and the lamp 
lifetime becomes longer.
 When this mode is switched, projected images may flicker.
 If this mode is frequently switched, the lamp may be deteriorated.
ASPECTNORMALAutomatically sets the aspect ratio in relative to the input signal. Use this 
setting for most cases.
16:9Selects a desired screen position for anamorphically squeezed or hori-
zontally compressed images stored on DVD disks.
FULL Select this setting when you want to project images in the full screen.
USER MENU Displays the menu item selected in SELECT USER MENU.
SELECT USER MENU Select the item to display in USER MENU.
DETAIL MENU Moves to DETAIL MENU.
Menu option Feature description
LAMP TIME (LOW)This menu shows a lamp operating time (hour) calculated assuming that LAMP MODE is LOW.
 When the LAMP MODE is STANDARD, this menu shows a longer lamp operating time than 
the actual time. (See page 28 for the interval of lamp replacement.)
 When the lamp operating time is 0 to 10 hours, 0H is displayed. When the lamp operating 
time exceeds 10 hours, the actual hours are displayed.
 When the lamp operating time reaches 3000 hours, the bar turns yellow. When it reaches 
3800 hours, the bar turns red.
(The lamp lifetime is 4000 hours.)
INPUT Indicates the name of the terminal to which the currently projected video signal is being input.
RESOLUTION Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY Indicates the vertical frequency of the currently projected video signal.
HORIZONTAL FRE-
QUENCYIndicates the horizontal frequency of the currently projected video signal.
SYNC. TYPE Indicates the type of the sync signal for the currently projected video signal.
DETAIL MENUSELECT
USER MENU ASPECT
USER MENU
NORMAL
OK
COLOR
QUICK MENU
CONTRAST
BRIGHTNESS0
0
STANDARD
STANDARD0
COLOR TEMP.
SHARPNESS
AUTO COLOR
ENHANCER
LAMP MODE
INFORMATION
LAMP TIME (LOW)
INPUT
RESOLUTIONVERTICAL
FREQUENCY
HORIZONTAL
FREQUENCY
SYNC. TYPE 5wire60.02 KHz75.04 Hz 1024x768 COMPUTER20 HRG
HVB 
						

							EN-18
Menu operation (continued)
DETAIL MENU* Menus are not displayed when no signal is supplied to the projector.
IMAGE
INSTALLATION
FEATURE
SIGNAL
INFORMATION
COLOR ENHANCER
CONTRASTBRIGHTNESS
COLOR TEMP.
AUTO
THEATER
PRESENTATIONSTANDARD
±30±30STANDARD
COLOR *1TINT *1SHARPNESS *1
ADVANCED MENU
±10±10±5
WALL SCREEN
LAMP MODESTANDBY MODEAUDIO INPUTAUTO POWER ONAUTO POWER OFFSPLASH SCREENBACK COLOR
IMAGE REVERSE
STANDARD, LOWSTANDARD, LOWAUTO, AUDIO 1, AUDIO 2, MIX     
OFF, 5, 10, 15, 30, 60 minON, OFF
BLACK BOARDWHITE BOARDOFF
BLUE, BLACKOFF, MIRROR, INVERT, MIRROR INVERT
LOW
GAMMA MODEBrilliantColor TMRGB-COLOR
RGB-TINT
HIGHCONTRAST RCONTRAST GCONTRAST BBRIGHTNESS RBRIGHTNESS GBRIGHTNESS B
NOISE REDUCTION *1CTI *1
INPUT LEVEL
DYNAMIC, NATURAL, DETAIL0-10±10±10
±30±30±30±30±30±30
ON, OFFON, OFF±5CLOSED CAPTION *1OFF, CC1, CC2
1-51-51-51-5
 ASPECT
SETUP *1LANGUAGERESET ALL
PASSWORD FUNCTIONMENU POSITIONCINEMA MODE *3VIDEO SIGNAL *5
WXGA *2
NORMAL
AUTO, OFF, 3.75%, 7.5%
DISPLAY INPUT      , MENU ACCESS           1 (upper left),  2 (lower right)
FULL
AUTO, OFFAUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60OFF, AUTO, 1280 x 768, 1280 x 768RB, 1360 x 768, 1366 x 768
LOCK
*4
*4
*4
*4
CENTER, UPPER, LOWER
OVER SCANHOLD *2
LAMP TIME RESET
HORIZ. POSITIONVERT. POSITIONFINE SYNC. *1 *2TRACKING *2
COMPUTER INPUT *2
100-90%OFF
0-9990-9990-310-2800AUTO, RGB, YCBCR/YPBPR
BEGINEND
SHUTTER (L)SHUTTER (LS)SHUTTER (RS)
CLAMP POSITION *2CLAMP WIDTH *2VERT. SYNCLPF *1 *2
SHUTTER (U)
0-990-99
0-200-200-20
1-2551-63AUTO, OFFON, OFF0-20
SYNC. TYPE *2
LAMP TIME (LOW)INPUTRESOLUTIONVERTICAL FREQUENCYHORIZONTAL FREQUENCY
OK     UNLOCKOK     
OK     
USEROK     
ON     
OK     
USER     
USER     
OK     
BEIGE     LIGHT BLUE     LIGHT GREEN     PINK     
16:9     
ON, OFF
, SVENSKA, POLSKI
AU1               AU2
*1 Not available with certain signals
*2 Not available when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
*3 Available only when the input signal is TV60, TV50, 480i, or 576i.
*4 The range that can be specified varies across input signals.
*5 Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal. 
						

							EN-19
ENGLISH
Menu operation (continued)
Basic operationSeveral settings can be adjusted using the menu.
Example : Auto power off time setting
1. Press the MENU button.
2. Select the DETAIL MENU and press the ENTER button  (or T 
button).
3. Press the W or X button to select INSTALLATION. 
4. Press the ENTER button (or T button).5. Press the S or T button to select AUTO POWER OFF.
6. Press the W or X button to adjust the auto power off time.
7. Exit the menu by pressing the MENU button several times.
Important:  When the button doesn’t function, unplug the power cord from the 
wall outlet. Wait about 10 minutes, plug the power cord in, and try 
again.
 After selecting the items marked with  , press the ENTER but-
ton.
Menu OptionsSet the following options provided in the respective menus.
1. IMAGE menu
 You cannot adjust TINT when the TV50 (PAL, SECAM) signal is inputted.
 You cannot adjust COLOR TEMP. when WALL SCREEN is set to other than OFF.
 When COMPUTER 1 or COMPUTER 2 is selected, COLOR and TINT do not work.
 When COLOR ENHANCER is switched, projected images may be distorted.
 Captions are not displayed while information about the menu, volume setting, or input signal selection is being displayed on the screen.
 The closed caption function displays text information included in the NTSC signal, which is mainly used for TV broadcasting in the United States.
IMAGE
opt.
INSTALLATION
opt.
INSTALLATION
opt.
WALL SCREEN
BEIGE
OFF AUTO POWER 
ON
OFFAUTO POWER OFF
30min AUTO POWER 
ON
OFFAUTO POWER OFF
Menu option Setting Feature description
IMAGE ADVANCED menu
COLOR ENHANCERAU TOAutomatically sets an optimal color balance based on the input signal. 
Use this setting for most cases.
PRESENTATION Makes projected images bright and crisp.
STANDARD Makes projected images look natural.
THEATER Makes projected images soft and smooth. Best suited for movies.
USER
 Adjusts the gamma curve, color intensity, or balance. (See page 23.)
CONTRAST±30 Adjusts the contrast of projected images. (See page 23.)
BRIGHTNESS±30 Adjusts the brightness of projected images. (See page 23.)
COLOR TEMP. 4 optionsAdjusts the color temperature. You cannot select this setting when 
WALL SCREEN in the INSTALLATION menu is set to a setting other 
than OFF. (See page 23.)
COLOR±10Adjusts the color tone of projected images. (See page 23.)  You cannot 
select this setting when the COMPUTER1 or COMPUTER2 is selected 
as the input source.
TINT±10Adjusts the color tint of projected images.  (See page 23.) You can 
select this setting only when NTSC is selected as the input signal.
SHARPNESS±5 Adjusts the sharpness of projected images. (See page 23.)
ADVANCED MENU OK
 NOISE REDUCTIONON/OFF Reduces noise of projected images when the input signal is noisy.
CTI ON/OFF Corrects smeared color borders.
INPUT LEVEL±5Adjusts the input level of analog video signals.
The input level of the video signal varies across devices to which the 
projector is connected. A high input level causes projected images to 
appear solid white, and a low input level causes projected images to 
appear dark.
CLOSED CAPTIONOFF Does not display captions.
CC1/CC2 Displays captions.
IMAGE
opt.
CONTRAST
BRIGHTNESS0
0
STANDARD
0 0
OK COLOR
TINT
ADVANCED MENU
COLOR TEMP.
0
SHARPNESS
AUTO COLOR
ENHANCER
IMAGEADVANCED MENU
CTI
INPUT LEVEL0 ON
ON NOISE REDUCTION
CLOSED CAPTIONOFF
opt. 
						

							EN-20
Menu operation (continued)
2. INSTALLATION menu
 By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, 
and you cannot switch the LAMP MODE in about one minute after the lamp is on.
Menu option Setting Feature description
WA LL  SC R EE NOFF/BEIGE / LIGHT 
BLUE / LIGHT 
GREEN / PINK /
BLACK BOARD/WHITE 
BOARDSelects a desired setting based on the color of the screen or wall on 
which images are projected.  (See page 15.) When selecting a setting 
other than BLACK BOARD/WHITE BOARD, you can fine-tune the color 
tone to the desired level on the 1 to 5 scale.
LAMP MODESTANDARD Select this setting when you want to view images in a well-lit room.
LOWSelect this setting when you want to view images at a moderate light 
intensity. The operating sound is consequently reduced, and the lamp 
lifetime becomes longer.
 When this mode is switched, projected images may flicker.
 If this mode is frequently switched, the lamp may be deteriorated. 
STANDBY MODESTANDARD LAN and MONITOR OUT can be activated in STANDARD MODE.
LOWPower consumption can be lowered when selecting LOW. However, LAN 
and MONITOR OUT cannot be activated.
AUDIO INPUTAU TOIf AUTO is selected, selects AUDIO 1 when the input source is COM-
PUTER, while selects AUDIO 2 when the input source is VIDEO/S-
VIDEO.
AUDIO 1/AUDIO 2 Select the audio input.
MIX
 Selects MIX signal of AUDIO 1 and AUDIO 2.  You can change the bal-
ance of AUDIO 1/AUDIO 2 using MIX .
AUTO POWER ON ON/OFFWhen this mode is set to ON, the lamp is automatically lit when the 
power cord is plugged in the wall outlet. Select ON when you set the 
projector at the ceiling.
 When the lamp is off, the projector is in standby. Use the remote 
control to turn on the lamp.
AUTO POWER OFF OFF/5-60 minSelects a desired timer setting until the projector enters the standby 
mode when there is no signal input from the source.
SPLASH SCREEN ON/OFF Select ON to display the splash screen when the projector is powered on.
BACK COLOR BLUE/BLACKSelects the background color that is displayed when there is no signal 
input from the source. 
IMAGE REVERSEOFFSelect this setting when you want to view images from the front with the 
projector set on the floor.
MIRRORSelect this setting when you want to view images from behind the 
screen with the projector set on the floor.
INVERTSelect this setting when you want to view images from behind the 
screen with the projector set at the ceiling.
MIRROR INVERTSelect this setting when you want to view images from the front with the 
projector set at the ceiling.
LAMP TIME RESET OK
 Resets LAMP TIME.
INSTALLATION
opt.
ONSPLASH 
SCREEN WALL SCREEN
LAMP MODE
STANDBY MODE
AUDIO INPUT
AUTO STANDARDBEIGE
ON STANDARD
OFF IMAGE 
REVERSE
AUTO POWER 
OFFOFF OFF AUTO POWER ON
BACK COLORBLUE
LAMP TIME
RESETOK