Mitsubishi Xd530e Data Projector User Manual

							EN-21
ENGLISH
Projecting images wirelessly
This section describes the procedure for projecting images on com-
puter screens using the wireless connection (wireless LAN).
 This data projector supports IEEE802.11b/g.
 When you use the wireless connection, the MONITOR OUT termi-
nal, AUDIO-IN terminal, and AUDIO-OUT terminal cannot be used.
 When you use the wireless connection and wired LAN connection, 
audio is not output.
A. Connecting the antenna
Preparation Make sure that the projector and the computer are turned off.
1. Connect the supplied antenna to the antenna terminal.
2. Stand the antenna up.
 Connect the antenna firmly so that it cannot be removed.
B. Plugging the power codeSee Preparation for projection on page 14.
C. Turning the power on and adjusting the 
focus
Preparation Remove the lens cap.
Turning on the projectorSee Basic operation on page 15.
Adjust the focusSee Basic operation on page 15.
D. Switching the input source1. Press the WIRELESS button on the remote control or the COM-
PUTER button on the control panel.
 Each time you press the COMPUTER button on the control 
panel, the input source is switched in the order of COM-
PUTER 1 → COMPUTER 2 → DVI → WIRELESS.
 When the screen flickers, press the W or X button on the 
remote control to reduce the flicker. If you switch the input source to WIRELESS, the starting 
screen appears, and then the following screen appears.
E. Connecting wirelessly Be sure to specify the settings as a user with Administrator rights.
 Log on to the computer as a user with Administrator rights in 
advance, and then check if the wireless connection is available. 
(For more details, see the manual of your computer.)
1. Turn the computer on.
2. Click the Start button, then select Control Panel.
3. Click Network and Internet Connections.
4. Click Network Connections.
5. Right-click Wireless Network Connection to select View Avail-
able Wireless Networks.
 
 If the wireless connection is set to Disable, right-click 
Wireless Network Connection to select Enable.
6. Select Wireless Projector ***, then click the [Connect] button.
 If the projector is wirelessly connected to the computer suc-
cessfully, Connected appears.
 The connection takes approximately one minute.
 If your computer and the projector are already connected 
wirelessly, close the window.
 If the projector and computer cannot be connected wire-
lessly, see page 44.
 You can change the character string subsequent to Wireless 
Projector in the administration screen.
 
STANDBY ON
ASPECT MAGNIFY
KEYSTONEVOL PAGE
UP
DOWN
MENU
FREEZE AUTO
POSITION
AV
MUTE
ENTER
1
2
COMPUTERVIDEOVIEWERUNPLUGS-VIDEO
WIRELESSDVI
ON button
VOLUME UP, DOWN 
buttons
Direction buttons
WIRELESS button 
						

							EN-22
Projecting images wirelessly (continued)
F. Installing the connection softwareInstall the connection software Wireless Projector which is required 
to project images on computer screens using this projector.
 Be sure to specify the settings as a user with Administrator rights.
1. Run the Web browser. (Example: Internet Explorer)
 The administration screen is displayed.
 If the screen is not displayed, display the Wireless Network 
Connection properties of your computer, and then check 
that Obtain an IP address automatically and Obtain DNS 
server address automatically are selected in the Internet 
Protocol (TCP/IP) properties.
 If the screen is not displayed, access http://(the IP address 
of the projector). The IP address is a numeric value dis-
played in Server IP: in the projected image.
 For details, see the following If the wireless connection fails 
on page 23.
2. Click Download.
 
3. Click the [Download] button.
4. Click the [Save] button.
 You can install the software directly without saving it.
 If it takes a long time to download the software, click the 
[Cancel] button, and then repeat the procedure from Step 3.
5. Specify the directory to save, and then click the [Save] button.
6. Double-click the file Wireless Projector.exe saved in Step 5.
7. Click the [Run] button.
8. Click the [Next >] button.
 The installation of Wireless Projector starts.
 When completing the installation, the connection software runs.
 If you install the software again during the wireless connection, the 
installation process stops. In this case, exit Wireless Projector 
once.
G. Projecting images
Running the connection software The software runs automatically right after the installation.
1. Double-click the Wireless Projector icon on the desktop.
2. Enter the login code indicated in red in the center of the projector 
screen, and then click the [OK] button.
 The image on the computer screen is projected.
 The login code is a four-digit number displayed in LOGIN 
CODE: in the projected image.
 For details on how to use the connection software, see page 
24.
Important: If a motion picture is projected wirelessly, dropping frames 
occurs according to the changing range.
 A portion of the range such as an icon which is being 
dragged may not be projected wirelessly.
Enter the same LOGIN CODE. 
						

							EN-23
ENGLISH
Projecting images wirelessly (continued)
If the wireless connection failsCheck the following points.
Check if the IP address and DNS server address are set to be 
obtained automatically in the Internet Protocol (TCP/IP) prop-
erties.
1. Perform the procedure from Step 2 to 5 in E. Connecting wire-
lessly.
2. Right-click Wireless Network Connection to select Proper-
ties.
3. Select Internet Protocol (TCP/IP), then click the [Properties] 
button.
 
4. Select Obtain an IP address automatically and Obtain DNS 
server address automatically, and then click the [OK] button.
Confirm that the Wireless Projector check box in the [Excep-
tions] tab in the Firewall settings is selected.
1. Perform the procedure from Step 2 to 3 in E. Connecting wire-
lessly.
2. Click Windows Firewall.3. Click the [Exceptions] tab.
4. Select the Wireless Projector check box, then click the [OK] 
button.
If the computer is used with a static IP address, make sure that 
the first three digits of the IP address in the Internet Protocol 
(TCP/IP) properties are the same as those of the IP address of 
the projector (indicated in Server IP: on the lower left of the 
default screen of the projector).
If not, conform the first three digits of their IP addresses to 
each other.
Internet Protocol (TCP/IP) properties
Default screen of the projector
Check if the first three digits 
conform to each other. 
						

							EN-24
How to use the connection software
For details on the procedure for running the connection software,
see page 22.
Pausing or resuming the projection
Pausing the projection
1. Click the   button.
Resuming the projection
1. Click the   button.
Updating the paused projectionYou can update the paused image to the one displayed on the com-
puter screen currently.
1. Click the   button while pausing images.
 Projected images are updated each time you click the button.
Stopping or starting the projection
Stopping the projection
1. Click the   button.
 Projecting the image on the computer screen stops, and the 
default screen of the projector appears.
Starting the projection
1. Click the   button.
Exiting the connection software1. Click the   icon, then select [Exit].
Important When multiple users have logged on the screen, users who logged 
on later are prioritized.
 Approximately 30 computers can be connected to the projector 
wirelessly at the same time. However, the number of connectable 
computers depends on the radio wave environment.
 If you want to connect to another projector, select the desired one 
in Step 6 in E. Connecting wirelessly on p. 21.
Other operation
Displaying the administration screen
1. Click the   icon, then select [Web Admin].
 For details on the administration screen, see page 26.
Reconnecting to the projectorIf the wireless connection to the projector is lost due to problems such 
as poor reception, you can reconnect to the projector.
 Set the input source of the projector to be switched to WIRE-
LESS in advance. (For more details, see page 21.)
1. Click the   icon, then select [Search Server].
2. Enter the login code, then click the [OK] button.
 
 The login code is a four-digit number displayed in LOGIN 
CODE: in the projected image.
Installing the connection software on a USB flash driveIf the connection software is installed on a USB flash drive in advance, 
you can use the connection software immediately on a computer 
equipped with USB ports. You do not need to install the connection 
software on the computer.
 When the connection software is installed on a USB flash drive, 
the volume name of the USB flash drive changes to PnS Token.
1. Insert the USB flash drive into a USB port of the computer on 
which the connection software is running.
2. Click the   icon, then select [Make PnS Token].
3. Click the [Next>] button.
Authentication code
Reception status (three levels) 
						

							EN-25
ENGLISH
How to use the connection software (continued)
4. Select the USB flash drive on which the connection software is 
to be installed, and then click the [Next>] button.
 Installation of the connection software starts.
5. Click the [Finish] button.
 The connection software starts automatically by inserting the USB 
flash drive on which the connection software is installed into a 
computer.
 If the connection software does not start automatically, open the 
USB flash drive, and then double-click the Wireless_Projector 
icon.
 While the connection software installed on a USB flash drive is 
running, do not remove the USB flash drive.
Displaying the information about the projectorYou can check the IP address and login code of the projector which is 
being connected.
1. Click the   icon, then select [Info].
2. Click the [OK] button after checking the information.
Displaying the version information of the software
1. Click the   icon, then select [About].
2. Click the [OK] button after checking the information. 
						

							EN-26
How to use the administration screen
Downloading the connection softwareThe procedure for downloading the software is the same as Step 1 to 
5 in F. Installing the connection software. See page 22.
Selecting the image to be projectedWhen connecting the projector to multiple computers wirelessly, one 
administrator can select the image to be projected from the 
computers.
 Approximately 30 computers can be connected to the projector 
wirelessly at the same time. However, the number of connectable 
computers depends on the radio wave environment.
1. Run the Web browser.
 The administration screen is displayed.
 If the screen is not displayed, access http://(the IP address 
of the projector). The IP address of the projector is a 
numeric value displayed in Server IP: in the projected 
image.
 You can also display the administration screen by selecting 
Web Admin in the menu of the connection software. See 
page 24.
2. Click Conference Control.
3. Enter a password, then click [Login].
 The list of the computers which are wirelessly connected to 
this projector is displayed.
 If chairman is specified for the user ID, the default 
password is chairman.
 You can change the password. See page 28.
4. Click OK.
5. Click the   icon for the computer of which you want to display 
the image.
 The icon in Play Control turns into  , and then the image is 
switched to that of the selected computer.
 While selecting the image to be projected in this screen, 
users other than the administrator cannot stop or start the 
projection using the connection software.
 When multiple users have logged on this screen, the only 
user who logged on first can operate. Users who logged on 
later cannot switch the image to be projected.
6. Click [Logout] after completing the operation.
Selecting a languageYou can select the language to be displayed in the administration 
screen between English and Japanese.
1. Run the Web browser.
 If the screen is not displayed, access http://(the IP address 
of the projector). The IP address of the projector is a 
numeric value displayed in Server IP: in the projected 
image.
 Once the browser is closed, the setting is reset to the default 
as it is not to be saved.
2. Click the pull-down menu on the upper right of the screen, and 
then select the language to be displayed.
Configuring the projectorAs well as changing the password, you can specify the settings for the 
network and the projection by logging on the system administrator 
screen.
1. Run the Web browser.
2. Click Admin.
3. Enter a password, then click [Login].
 If admin is specified for the user ID, the default password is 
admin.
 You can change the password. See page 28.
Checking the status of the projectorYou can check the model name, version, network status, and connec-
tion status of the projector.
1. Click System Status. 
						

							EN-27
ENGLISH
How to use the administration screen (continued)
Changing the network settings For the setting items, ask your network administrator.
1. Click Network Setup.
2. Change the settings, then click the [Apply] button. You can change the following settings.
 When using multiple units of the wireless projector, do not 
overlap the settings for SSID in Wireless Setup.
3. Check the displayed settings, then click the [OK] button.
4. Reboot the system.
 The specified settings can be applied.
 It takes approximately one minute to reboot the system.Settings Contents
IP Setup If the projector is connected to a DHCP 
network, select Obtain an IP address 
automatically.
 If the projector is used with a static IP, 
select Use the following IP address:, and 
then specify the values for IP Address, 
Subnet Mask, and Default Gateway.
 You cannot specify prohibited IP addresses 
such as 0.0.0.0 and 255.255.255.255.
DHCP Server Setup If the projector is connected to computers, 
it functions as a server and can assign IP 
addresses to the computers. If you want 
the projector to assign IP addresses, select 
Auto.
 If you select Auto, select Obtain an IP 
address automatically for the TCP/IP set-
tings in the computer.
 The range in which the IP addresses are 
assigned is displayed in Start IP and 
End IP. These IP addresses are changed 
automatically if the IP address of the pro-
jector is changed.
Wireless Setup You can choose Enable or Disable for 
Wireless LAN. If you selected Disable 
for Wireless LAN, you can enable it again 
by connecting using Wired LAN or perform-
ing NETWORK RESET in the WIRELESS 
menu of the projector.
 You can specify a value of 14 digits that fol-
low Wireless Projector as a SSID.
 If you enable SSID Broadcast, you can 
search Wireless Projector automatically. 
Also, you can disable SSID Broadcast for 
security improvement. If you selected Dis-
able for SSID Broadcast, you can enable 
it again by connecting using Wired LAN or 
performing NETWORK RESET in the 
WIRELESS menu of the projector.
Channel The model for North America has 11 chan-
nels, and that for Europe has 13 channels. 
If you select Auto, you can select a chan-
nel, which is in an optimum radio wave 
environment, from the above channels.
 If the radio wave environment is poor dur-
ing use, switch to another channel manu-
ally.
WEP You can improve security for the wireless 
communication by encrypting it between 
the projector and computers.
 If you use the WEP function, select 128-bit 
(ASCII: 13 characters), 64-bit (ASCII: 5 
characters), 128-bit (Hex: 26 digits), or 64-
bit (Hex: 10 digits). Specify a key according 
to the number of the characters/digits.
 You are required to enter the above speci-
fied key when connecting the projector 
wirelessly. Enter the specified key. 
						

							EN-28
How to use the administration screen (continued)
Glossary
Changing the settings for the projectionYou can change the settings for the number of colors and the login 
code.
1. Click Projection Setup.
2. Change the settings, then click the [Apply] button. You can change the following settings.
3. Check the displayed settings, then click the [OK] button.
4. Reboot the system.
 The specified settings can be applied.
 It takes approximately one minute to reboot the system.
Changing the passwordYou can change the passwords for the user (trainer) and administrator 
(admin).
1. Click Change Passwords.
2. Enter a new password in Conference Control or Admin, and 
then click each [Apply] button.
Restoring the default settingsYou can restore the default settings.
1. Click Reset to Default.
2. Click the [Apply] button.
3. Check the displayed settings, then click the [OK] button.
4. Reboot the system.
 The default settings can be restored.
 It takes approximately one minute to reboot the system.
TCP/IP Transmission Control Protocol/Internet Protocol 
(TCP/IP) is the standard protocol used for network-
ing. Protocol is a set of technical rules for the trans-
mission of information between computers.
IP Address IP Address is the numbered address to identify a 
server for networking. Internet Protocol (IP) is the 
protocol to transmit data over the Internet, and the IP 
Address, which consists of exactly same numbers as 
the other address in one network, is not available.
DHCP Dynamic Host Configuration Protocol (DHCP) is the 
protocol dynamically allocating IP addresses to com-
puters on a local area network. The computer with 
DHCP server can assign IP address to each com-
puter on a local area network automatically.
Subnet Mask Subnet is the separated part of network, and subnet 
mask is a number that defines a range of IP 
addresses that can be used in the network.
Gateway Gateway is either hardware or software that acts as 
a bridge between two networks. Gateway is a sys-
tem for transmitting data across networks that are 
incompatible and use different protocols.
WEP Wired Equivalent Privacy (WEP) is a security proto-
col that adds security by encrypting data. The 
encryption key enables only the authorized systems 
on the network to recognize the data.
SSID Service Set ID (SSID) is the identifier for wireless 
local area networks, which identifies the access 
points necessary for transmitting. Some wireless 
local area network card uses [ESSID (Extended Ser-
vice Set Identifier)] or network name as SSID.Settings Contents
Resolution The resolution of this projector is fixed at XGA.
Color DepthYou can specify the number of colors for the pro-
jected images.
You can select Normal (16 bit) (65,536 colors) 
or High (32 bit) (16,777,216 colors).
Screen Refresh Rate The rate of this projector is fixed at 75 Hz.
Login CodeYou can specify the login code to connect to the 
projector wirelessly.
 Disable: You can connect to the projector wire-
lessly without entering the login code.
 Random: The login code is changed randomly 
each time the projector starts up. (Default)
 Use the following code: Specify the login code. 
The login code is a four-digit number. 
						

							EN-29
ENGLISH
Uninstalling the connection software
This section describes the procedure for uninstalling the connection 
software.
1. Click the Start button, then select [All Programs] → [Wireless 
Projector] → [Uninstall].
2. Click the [Yes] button.
 The uninstallation of the connection software Wireless Pro-
jector starts.
3. Click the [OK] button. 
						

							EN-30
How to use wired LAN connection
The function described in the previous section for the wireless connection can be applied also to the wired LAN connection similarly.
When the wireless connection is poor and the network settings cannot be configured, use the function.
For Ethernet connection  
1. Connect one end of the Ethernet cable to the LAN terminal of the projector.
 Use a cross cable.
 Use a Category 5 cable.
2. Connect the other end of the Ethernet cable to the Ethernet port of the computer.
 To project images, use the connection software. For details, see the sections B - F and G. Projecting images in Projecting images wire-
lessly. (See page 21 and 22.)
Important: When the wireless environment is poor, if you want to configure the network settings securely, or in other cases, use the connection.
 When turning on the devices, turn on the projector first, and then turn on the computer after the screen of the projector appears. If you turn on 
the computer first, the projector may not operate properly.
 Specify the settings for the Internet Protocol (TCP/IP) properties in Local Area Connection according to those specified in Changing the net-
work settings (See page 27). In the default settings, Obtain an IP address automatically is selected.
 When you use the wired LAN connection, the MONITOR OUT terminal, AUDIO-IN terminal, and AUDIO-OUT terminal cannot be used.
 Do not touch the LAN terminal directly with your hand as you may be shocked by static electricity.
LAN
LAN terminal
Computer
to Ethernet
port LAN cross cable (10BASE-T or 100BASE-TX)