Mountfield Lanw Mower MULTICLIP 501SP 291502148/BQ Operating Instructions

							Please Read These Instructions
Before Using Your Mower
Call our Helpline if you have any problems:-
0845 600 2912
Open from 9:00am to 5:00pm Monday to Saturday
10.00am to 4.00pm on Sunday
Product Code:
291502148/BQ
These instructions are an addition to and should be read in
conjunction with the Operator Manual enclosed with this mower
Operating Instructions
for model
 Multiclip 501SP Lawnmower
with Mountfield RM45 engine 
						

							Thank you for purchasing a Mountfield  lawnmower. This machine  will give you many years of safe  and
reliable service if operated in accordance with these instructions. Please read and understand these
Operating Instructions before using your mower,  failure to do so could result in personal injury
or  damage  to the  equipment.
NEVER  TIP THE  MOWER  FORWARDS  OR ON ITS  SIDE  AS THIS  WILL  FLOOD  THE CYLINDER  AND AIR
FIL TER  WITH  OIL.  To  access the underside,  lift the  front  wheels  by lowering  the handle  until it rests  on the
ground.
 SAFETY PRECAUTIONS
The  following  safety  precautions  must  be  observed  at  all  times.  Please read  them very care-
fully.
GENERAL
• Know how to stop your mower quickly in an emergency.   Understand all the controls and how they operate.
• Do not allow children or anyone who is unfamiliar with these instructions to use the mower.  Local regulations
may restrict the age of the operator.
• Keep

 children, pets and other bystanders well away from the work area.
• Never put your hands, feet or any implement under the cutter deck.  The cutter blade will continue to rotate for
some time after the engine is switched off.
STOP THE ENGINE AND DISCONNECT THE SPARK PLUG LEAD
• Before carrying out any adjustments, cleaning, inspection or maintenance.
• If your mower is damaged or vibrates excessively.   Ensure the machine is in a safe working condition before it
is restarted.
• Before  clearing  any blockage.
STOP  THE ENGINE
• Whenever  you leave  the mower  unattended.
• Before refilling with petrol or oil.
PR EPAR ATION
• Wear  sturdy  footwear  and  long  trousers  when  using  the  mower.  Never  go  barefoot  or  wear  open  sandals.
Avoid loose clothing that may snag on moving parts.
• Check  the work  area and remove  any stones  or other  debris  that may  be thrown  up by,  or cause  damage  to, the
cutter blade.
• Before use ensure that the mower is in a safe working condition.   Inspect the cutter blade for damage; check
safety devices and guards; check that all nuts, bolts and screws are secure.
• Never use the machine without a silencer; or with a faulty silencer.
FUEL  SAFETY
       WARNING!  –   PETROL IS
 HIGHLY FLAMMABLE AND EXPLOSIVE UNDER CERTAIN CONDITIONS.
• Store petrol in a cool place and only in containers specifically designed for the purpose.
• Refuel  outdoors  only, with the  engine stopped.  DO NOT SMOKE  while refuelling.
• After refuelling, replace the fuel tank cap and the petrol container cap securely.
• Never remove the fuel tank cap, or add petrol, when the engine is hot or when it is still running.
• If  any  petrol  is  spilt  do  not  attempt  to  start  the  engine.   Move  the  mower  away  from  the  area,  clean  up  the
spillage and allow the fumes to dissipate before starting the engine.
Read these
instructions
before using your  mower. Keep hands and
feet well away
from the cutter blade. Warning!
Remove the
spark plug lead before working on the mower. Beware of
objects that may be thrown up by the blade. Keep children,
bystanders  and
pets away from the work area. Warning!
Hot surfaces 
						

							OPERATION
•Do not operate the engine in a confined space.  Exhaust fumes contain CARBON MONOXIDE, an odourless and
POISONOUS gas.
•Mow only in daylight or good artificial light.
•Check the oil and fuel levels before starting the engine.
•Disengage the engine brake and drive clutch before starting the engine.
•Start the engine in accordance with the instructions and with feet well away from the cutter blade.
•Do not tilt the mower when starting the engine.
•Do not change the engine settings.  If adjustments are necessary, contact your dealer.
•Operate the machine at a comfortable walking pace, never run behind the mower.
•Avoid operating the machine on wet grass whenever possible.
•Take care when working on slopes.  Mow across the slope, never up and down, and exercise caution when
changing direction.  Do not use the mower on slopes of more than 20 degrees.
•Exercise extreme caution when reversing or pulling the mower towards you.
•Stop the cutter blade when crossing surfaces other than grass and when transporting the mower to and from the
work area.
•Never pick up or carry the mower when the engine is running.
STORAGE & MAINTENANCE
•To reduce the risk of fire, keep the mower and petrol storage areas free of grass, leaves and grease.
•Check the mower and grass collector regularly to ensure the machine is in a safe working condition.  Replace any
worn or defective parts. Only use genuine replacement parts.
•Store the mower in a dry, secure place out of the reach of children and well away from any fire hazard.
•Allow the engine to cool before storage.  If the fuel tank has to be drained, this should be done outdoors.
KNOW YOUR MOWER
Drive Clutch
LeverOperator Presence
Control (OPC)
Lever
Height of Cut Adjuster Engine
Cutter DeckFuel Filler Cap
(located at rear of
engine)
Handle
Securing Knob Pull Cord & Guide
Spark Plug
Oil Filler Cap/Dipstick(located at rear of engine)
Throttle Control
Air Filter
Exhaust 
						

							 HOW TO GET MOWING
Your Mountfield lawnmower does not contain petrol or oil and these must be added before use.  Running
the mower with insufficient oil can cause serious damage to the engine and will invalidate your
warranty.
NEVER TIP THE MOWER FORWARDS OR ONTO ITS SIDE AS THIS WILL FLOOD THE CYLINDER
AND AIR FILTER WITH OIL.
To access the underside of the machine lift the front wheels by lowering the handle to the ground.
Carefully remove the mower from the carton and read these Operating Instructions.  An Owner’s Manual
for the engine is also included, please read this before starting the engine.
HANDLE ASSEMBLY (Figure 1)
•Fit the upper part of the handle (1) to the lower part (2) using the knob (3) and washer (4) supplied.
•Engage the Operator Presence Control (OPC) lever to release the engine brake.  Pull the starter cord (5), fit it into
the cord guide (6) and tighten the cord guide fixing nut  (7).
•Use the cable ties (8) to fit the OPC cable and clutch cable to the handle assembly.  Take care that the cables will
not impair adjustment of the handles.
•Before starting work check that the lower handle securing screws (9) and the adjusting knob (3) are fully tight-
ened.
HANDLE ADJUSTMENT (Figure 2)
•    
  The upper part of the handle (1) can be offset to either side
to facilitate working near walls or hedges.
Loosen the knob (3) move the upper handle to the desired
position and retighten the knob.
Figure 1
Figure 2 
						

							STARTING YOUR MOWER
Read and understand the Safety Precautions before using your mower.
•Put Mountfield 4-stroke, or an SAE 10W-30 oil, in the oil filler (Figure 3).  Do not overfill, the oil tank capacity is
0.55 litre. Mountfield oil, part number MX855, is available from any Mountfield stockist or B&Q store.
•Fill the fuel tank with UNLEADED petrol.  Use only clean, fresh petrol - stale fuel may contain deposits that will
clog the carburettor.  Do not overfill, the petrol level should be below the bottom of the fuel tank neck..
•Ensure that the spark plug lead is securely connected to the spark plug.
•Move the throttle control to the “Choke” positiion (Figure 4).
•Pull and hold the Operators Presence Control (OPC) lever against the handle to disengage the engine brake.
THE ENGINE WILL NOT START, OR CONTINUE TO RUN, UNLESS THE OPC LEVER IS HELD AGAINST
THE HANDLE.
•Pull the starter cord with a strong smooth pull.  Do not remove the pull cord from the guide.
•When the engine starts move the throttle control from “Choke” to the “Fast” position.
NOTE: Using the choke is usually unnecessary when starting a warm engine.  However, in cool weather it may still be
necessary to use the choke to start the engine.
ENGAGING THE DRIVE (Figure 5)
•   The forward drive is operated by moving the clutch control lever (1)
towards the operator.  Do not engage the drive unless the engine is
running.
 To dis-engage the drive move the lever towards position “N”.
 Releasing the Operator Presence Control (OPC) lever automati-
cally moves the drive lever (1) to position “N” stopping forward move-
ment.
STOPPING YOUR MOWER
•Move the throttle control lever to the “Slow” (tortoise) position.
Release the Operators Presence Control (OPC) lever; this will
engage the engine brake and operate the ignition safety cut out device.
HEIGHT OF CUT ADJUSTMENT (Figure 6)
This mower has a MULCHING system which cuts the grass into fine
particles which are blown down into the base of the turf to decompose.
There are no grass clippings left to be collected.
To obtain the best results from your mower:
•operate the mower with the engine running at a high speed (full
throttle)
•do not cut the grass when it is wet
•cut no more than 1/3 off the length of the grass at a time
•ensure the underside of the cutter deck is kept clear of grass debris
•always use a sharp cutter blade
To adjust the height of cut:
•stop the engine and disconnect the spark plug.
•put the mower on a level surface.
•adjust the cutting height lever (1) by pulling outwards and moving into the required position.
Figure 5
Figure 3 Oil Filler Cap/
DipstickFuel Filler Cap
Exhaust
Spark PlugAir Filter Pull Cord
HandleFigure 4
Figure 6 
						

							Stop the engine and disconnect the spark plug lead before working on the machine.  DO NOT TIP
THE MOWER FORWARD OR ONTO ITS SIDE AS THIS WILL FLOOD THE CYLINDER AND AIR FILTER
WITH OIL.  To access the underside of the machine, lift the front wheels by lowering the handle
until it rests on the ground.
CUTTER BLADE
Examine the cutter blade regularly for wear or damage.
•A slightly worn blade can be re-sharpened by your local dealer.
•If the blade is damaged it should be replaced.  Replacement blade kits
are available from your Mountfield stockist.   If in doubt refer to your
dealer, or telephone 0845 600 2912.
CLUTCH (Figure 8)
•Once or twice a year clean the area around the transmission and drive
belt.
• Remove the guard (1) by unscrewing the screws (2) and releasing the
couplings (3).
•Using a brush or compressed air carefully remove any grass and dirt
from aound the transmission and drive belt.
•Always refit the guard (1).
ENGINE
An engine manufacturer’s Owner’s Manual is supplied with your mower.
Please read this, it provides detailed information on engine operation,
maintenance and battery care.  Repair work other than routine maintenance,
should be carried out by an authorised dealer.
STORAGE
A little time spent on your mower after use will ensure many years of reliable mowing.  To access the underside of the
cutter deck, ensure the spark plug lead is disconnected, then lift the front wheels by lowering the handle until it rests
on the ground.  Do not tip the mower onto its side, as this will flood the air filter with oil.
AFTER EACH USE
•Remove any grass pulp from the underside of the cutter deck using a non-metallic instrument such as a piece of
wood.  Take care not to damage the paintwork.
•Examine the cutter blade for any damage.  A damaged blade may upset the balance of your mower and cause
excessive vibration, if in doubt refer to your dealer.
•The upper handle can be removed and folded down to reduce the amount of storage space required.  Take care
not to trap any of the operating cables when removing or refitting the handle.
•Store the mower in a clean, dry area well away from any naked flames, sparks or heat source.
LONG TERM - If you are not using your mower for more than 28 days.
•Give the machine a thorough clean, paying particular attention to the underside of the cutter deck.
•Lubricate all moving parts.
•At the end of the season, empty the fuel tank either by running the mower out of fuel or tip the machine backwards
and onto the back right wheel to drain the fuel into a suitable container.  Drain the carburettor by loosening the
drain screw, retighten the drain screw.
MAINTENANCE
Figure 8
Figure 7 BEFORE EACH USE
•Always ensure that the mower is in a safe working condition.  Inspect the cutter blade for damage; check safety
devices and guards; check that all nuts, bolts and screws are secure.
•Check the oil level as follows:
a) Remove the oil filler cap and wipe the dipstick clean (Figure 7).
b) Insert the dipstick into the filler neck and tighten down again.
Remove the dipstick and check the oil level; oil should be at the MAX
mark.  The oil tank capacity is about 0.55 litre or 18 fluid oz.
c) If the oil level is low add Mountfield oil part number MX855 or a
SAE 10W-30 oil, to the upper limit on the dipstick.  Do not overfill; the
oil level should not be above the FULL mark.
•Fill the fuel tank with unleaded petrol.  Do not overfill; the level should
be below the bottom of the fuel tank neck. 
						

							NOIT U LO S
M EL B O RP
Chec k t h ere  i s a m ple  c le an ,  f r esh  f u e l i n  t h e  t a n k.En g in e w ill n o t s ta rt
Chec k t h e c u tte r b lade  i s   n o t f o ulin g t h e g ro un d p re ve n tin g f r e e  r o ta tio n .
C he ck  t h e O pera to rs  P re se n ce  C ontro l ( O PC ) l e ve r i s  f u ll y  r e le ase d .En g in e w ill n o t s to p
Rem ove  s p ark  p lu g  l e a d  t o  s to p  e n g in e u sin g  i n su la te d  g l oves  a n d  r e fe r  t o  d eale r.
S to p  t h e e n gin e a n d d is c o nn ect t h e s p ar k p lu g l e ad  u sin g  h eat r e sis ta n t g lo ve s.
C hec k b la d e a tt a ch men t b olt  i s  t ig h t.F a il u re  t o  c u t g r as s p ro p erly
Chec k c o ndit io n o f b la d e.  If  s erio u sly  w orn  o r  dama ged  r e p la ce  w it h  a  n ew  o ne.
Sto p  t h e e n gin e a n d d is c o nn ect t h e s p ar k p lu g l e ad  u sin g  h eat r e sis ta n t g lo ve s.
C hec k a n d m ake  s u re  t h ere  i s  n o  b uil d   up  o f g ra s s in sid e t h e ca sin g.
C he ck t o  e n su re  t h e  eng in e i s  r unn in g a t t h e c o rr e c t s p ee d , ( a ppro xim ate ly  3 0 00rp m ).
Rais
e the  height o f cut to inc rease  airfow.
Do  not cu t more than  one third of the  length o f the  grass a t any  one time.
Fa il u re  t o  c o lle ct g ra ss p ro p erly
M ach in e v ib ra te s e xc ess i ve ly T
h is  w ill  c erta in ly  i n d ic a te  t h at  t h e  b la d e h as  beco m e b ad ly  d a mag ed .   S t o p  t h e e ng in e,  d is c o n n ect t h e
s p ark  p lu g  l e ad  a n d  e xa m in e  t h e b la d e a sse mbly .   R efe r  t o  y o ur l o ca l d eale r.
F AUL T FINDING
 CERTIFICA TE OF  CONFORMITY
EC DECLARA TION OF CONFORMITY
The company  ................................................... GGP ITALY  SP A -  V ia  de l Lavo ro, 6
31033  Castelfranco V .t o ( TV)  ITALY
M ult ic lip 501S P typ e MCS 504 TR
48  cm
GGP  •  WB E 0702
S NCH, 1 1 r oute de  Luxembour g
L -5230 SANDWEILER
98/ 37/EEC
89/ 336/EEC  ~ 2004/108/EC -  2000/ 14/EC
ANNEX VI
93  dB(A)
94 dB(A)
E N  836  - EN  292-2- EN  1033  - EN  ISO 3767
E N  ISO 14982
79 dB(A)
9 ,5  m /s
2
Cert ify that the  lawnmower , walk behind  with
c ombustion  engine  ...........................................
W idht o f cut  .....................................................
E ngine ..............................................................
T e sted  by  .........................................................
Conf orms to  the spec if ca tions o f direct iv e s  .....
Castel franco V en eto ( TV) -  IT ALY 01-10-2008
Conf
ormity a ssessment proc edure followed ......
Meas ured sound  power level ............................
G uarant eed sound  power level .........................
Ref erenc e to  harmonis ed standards..................
S ound  pressure  level at the  ear measured  in compli-
anc e wit h 81/ 1051/EEC  ..............................................
V irat ion  level  at the  handle  (E N  1033) .......................
S. Ferrari ( Gen eral Man ag er) 
						

							GGP UK LIMITED
Uni t 8,  Blu ewater  Estate , B ell  Close , Plympton,  Plymouth, Devon,  PL7  4JH , Engl and.
Part  Number 171503945/0
Guarantee
GGP  UK  Limited  undertakes  to provide  a full  guarantee  against defective  materials  or workmanship
for  two  years  from the date  of purchase  subject to the  mower  receiving  an annual  service.
If  the  machine  is used  for commercial  purposes; i.e . for  hire;  or by  contractors,  caravan sites or
si milar  use rs,  this  guarantee  period shall be 90 days.
If  any  part  or  parts  are  found  to be  defe ctive  within  the guarantee  period, GGP UK  Limi ted,  via their
authorised  dealer, will  effect  the repair or replacement  at  no  charge  to the  owner  providing  that the
fault  is reported  direct  to the  deale r.   All  repairs  must  be carried  out by an  authorised  Mountfield
dealer .  Delivery  and  coll ection
 of  t he  machin e is  t he  owne r’s  respons ibility and  not  c overed
und er the  terms  of this  guarantee.
This  guarantee  is not  transferable.  Proof  of purchase  will  be required  in the  event  of a  claim.
This  guarantee  does not apply  to the  routine  replacement  of parts  that are subject  to normal  wear and
tear  – or  to normal  service  and maintenance  parts.  This  guarantee  does not cover  faults caused  by
neglect  or misuse.
The  engine  manufacturer  guarantees the engine  fitted to this  machine.
This  guarantee  is in  addition  to, and  does  not detract  from, the contractual  rights of the  owner  under
s tatute  or common  law.
On  delivery  of your  new Mountfield  mower, we suggest
that  you complete  the  box  to the  right.
T he  informat ion for  your  machine  is on  the  serial
number  label,  which  is  fixed  on the  cutter  deck at the
base  of the  handles.  You  will be asked  for these  details
if  you 
have  any problems  or  require  spare  parts.
Please  keep  your receipt,  proof of purchase  will  be
required  in  the  event  of a claim.
Serv ic e  R eco rd
1st  Serv ic e2 n d  S erv ic e
:
e
c
i
v
r
e
S
 
f
o
 
e
t
a
D
:
e
c
i
v
r
e
S
 
f
o
 
e
t
a
D
:
e
u
D
 
e
c
i
v
r
e
S
 
t
x
e
N
:
e
u
D
 
e
c
i
v
r
e
S
 
t
x
e
N
:
e
r
u
t
a
n
g
i
S
 
s
’
r
e
l
a
e
D
:
e
r
u
t
a
n
g
i
S
 
s
’
r
e
l
a
e
D
:
p
m
a
t
S
 
s
’
r
e
l
a
e
D
:
p
m
a
t
S
 
s
’
r
e
l
a
e
D