MSI H87-g41 Manual

							
Chapter 1
1-17Getting Started

Power Supply
 Video Demonstration
Watch the video to learn how to install power supply connectors.
http://youtu.be/gkDYyR_83I4
JPWR1~2: ATX Power Connectors
These connectors allow you to connect an ATX power supply. To connect the ATX power supply, align the power supply cable with the connector and firmly press the cable into the connector. If done correctly, the clip on the power cable should be hooked on the motherboard’s power connector.
1 3 . + 3 . 3
V
1 . + 3 . 3
V
1 4 . - 1 2 V
2 . + 3 . 3
V
1 5 . G r o u n d
3. G r o u n d
1 6 . P S - O N
#
4 . + 5V
1 7 . G r o u n d
5. G r o u n d
1 8 . G r o u n d
6 . + 5V
1 9 . G r o u n d
7. G r o u n d
2 2 . + 5V
1 0 . + 1 2 V
2 0 . R e s
8 . P WR OK
2 3 . + 5V
11. + 1 2 V
2 1 . + 5V
9 . 5 V S B
2 4 . G r o u n d
1 2 . + 3 . 3
V
7 . + 1 2 V
3 .G r o u n d
5 . + 1 2 V
1 .G r o u n d
8 . + 1 2 V
4. G r o u n d
6 . + 1 2 V
2. G r o u n dJPWR2
JPWR1
 Important
Make sure that all the power cables are securely connected to a proper ATX power supply to ensure stable operation of the motherboard. 
						

							
Chapter 1
1-18Getting Started

Expansion Slots
This motherboard contains numerous slots for expansion cards, such as discrete graphics or audio cards.
PCI_E1~4: PCIe Expansion Slots
The PCIe slot supports the PCIe interface expansion card.
PCIe 2.0 x1 Slot
PCIe 3.0 x16 Slot
PCIe 2.0 x16 Slot
PCI1~2: PCI Expansion Slots
The PCI slot supports the PCI interface expansion card..
PCI Slot
 Important
When adding or removing expansion cards, always turn off the power supply and unplug the power supply power cable from the power outlet. Read the expansion card’s documentation to check for any necessary additional hardware or software changes. 
						

							
Chapter 1
1-19Getting Started

Video/ Graphics Cards 
If available, this motherboard takes advantage of the CPU’s integrate graphics processor, but discrete video cards can be installed by way of the motherboard’s expansion slots. Adding on one or more discrete video cards will significantly boost the system’s graphics performance. For best compatibility, MSI graphics cards are recommended.
 Video Demonstration
Watch the video to learn how to install a graphics card on PCIe x16 slot with butterfly lock.
http://youtu.be/mG0GZpr9w_A
Single Video Card Installation
Determine what type of expansion slot(s) the video card will use. Locate the expansion slot(s) on the motherboard. Remove any protective expansion slot covers from the computer case. 
Line up the video card on top of the expansion slot(s) with the display ports facing out of the computer case. For a single video card installation, using the PCI_E2 slot is recommended. 
Push the video card into its expansion slot(s). Depending on the expansion slot(s) used, there should be clip(s) on the expansion slot(s) that will lock in place.
If needed, screw the edge of the graphics card to the computer case. Some video cards might require a power cable directly from the power supply.
Please consult your video card’s manual for further instructions regarding driver installation or other special settings.
1.
2.
3.
4.
5. 
						

							
Chapter 1
1-20Getting Started

AMD CrossFire™ (Multi-GPU) Technology
AMD CrossFire™ is a multi-GPU performance gaming platform. By linking together two or more discrete GPUs, CrossFire™ can significant improve system graphics performance. It allows the ability to scale a system’s graphics power as needed, making it the most scalable gaming platform. This motherboard will automatically detect CrossFire™ technology and make changes in the BIOS as needed. Follow the instructions below to ensure a successful two-way CrossFire™ installation. 
Install two AMD Radeon™ HD graphics cards into the PCI_E2 & PCI_E4 expansion slots.
With the two cards installed, two CrossFire™ Video Link cable are required to connect the graphics cards. Attach one side of the cable on each of the cards by way of the metal contacts (please refer to the picture below). Please note that although two graphics cards have been installed, only the display ports on the graphics card installed in the first PCIe x16 slot will work. All displays should be connected to this graphics card.
1.
2.
 Important
Please ensure that all graphics cards used in CrossFire™ mode are of the same brand and specifications. For best compatibility with the motherboard, MSI graphics cards are recommended.
Make sure to connect an adequate power supply to the power connectors on the graphics cards to ensure stable operation. 
Only Windows™ 7 will support CrossFire™ mode.
•
•
•
CrossFire Video Link Cable 
						

							
Chapter 1
1-21Getting Started

Boot up the computer and install the drivers and software included in your video card package. For more information, please refer to the manual that came with your video card. 
After all of the hardware and software has been properly installed, reboot the system. After entering the operating system (OS), right click on the desktop and choose  the “Catalyst Control Center”. 
3.
4.
The CrossFire™ setting must be enabled to allow CrossFire™ mode to operate. The follow screen appears in the Catalyst Control Center. Depending on your operating system, the screen may look different.
5.
 Important
A CrossFireTM system has four possible display modes:
SuperTiling
Scissor Mode
Alternate Frame Rendering
Super Anti-aliasing.
For more details, please consult the graphics card manual.
•
•
•
• 
						

							
Chapter 1
1-22Getting Started

Internal Connectors
SATA1~6: SATA Connectors 
This connector is a high-speed SATA interface port. Each connector can connect to one SATA device. SATA devices include disk drives (HDD), solid state drives (SSD), and optical drives (CD/ DVD/ Blu-Ray).
 Video Demonstration
Watch the video to learn how to Install SATA HDD.
http://youtu.be/RZsMpqxythc
SATA1
SATA4
SATA3SATA6
SATA5
SATA2
For Z87-G41 PC Mate/ H87-G41 PC Mate
- SATA1~6 (6Gb/s, by Intel® Z87/ H87)
For B85-G41 PC Mate
- SATA1, SATA2, SATA3, SATA4 (6Gb/s, by Intel® B85)
- SATA5, SATA6 (3Gb/s, by Intel® B85)
 Important
Many SATA devices also need a power cable from the power supply. Such devices include disk drives (HDD), solid state drives (SSD), and optical drives (CD / DVD / Blu-Ray).  Please refer to the device’s manual for further information. 
Many computer cases also require that large SATA devices, such as HDDs, SSDs, and optical drives, be screwed down into the case. Refer to the manual that came with your computer case or your SATA device for further installation instructions.  
Please do not fold the SATA cable at a 90-degree angle. Data loss may result during transmission otherwise.
SATA cables have identical plugs on either sides of the cable. However, it is recommended that the flat connector be connected to the motherboard for space saving purposes.
•
•
•
• 
						

							
Chapter 1
1-23Getting Started

CPUFAN1~2,SYSFAN1~3: Fan Power Connectors
The fan power connectors support system cooling fans with +12V. If the motherboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with a speed sensor to take advantage of the CPU fan control.  Remember to connect all system fans. Some system fans may not connect to the motherboard and will instead connect to the power supply directly. A system fan can be plugged into any available system fan connector.
1. G r o u n d2 . S p e e d
Co n t r ol
3 . S e n s
e4 . N C
1. G r o u n d2 . + 1 2 V3 . S e n s
e4 . S p e e d
Co n t r ol
SYSFAN2/
SYSFAN31. G r o u n d2 . + 1 2 V3 . N oU se
CPUFAN1/
CPUFAN2
SYSFAN1
 Important
Please refer to your processor’s official website or consult your vendor to find recommended CPU heatsink. 
These connectors support Smart Fan Control with liner mode. The Command Center utility can be installed to automatically control the fan speeds according to the CPU’s and system’s temperature. 
If there are not enough ports on the motherboard to connect all system fans, adapters are available to connect a fan directly to a power supply. 
Before first boot up, ensure that there are no cables impeding any fan blades.
•
•
•
• 
						

							
Chapter 1
1-24Getting Started

JFP1, JFP2: System Panel Connectors
These connectors connect to the front panel switches and LEDs. The JFP1 connector is compliant with the Intel® Front Panel I/O Connectivity Design Guide. When installing the front panel connectors, please use the optional M-Connector to simplify installation. Plug all the wires from the computer case into the M-Connector and then plug the M-Connector into the motherboard.
 Video Demonstration
Watch the video to learn how to Install front panel connectors.
http://youtu.be/DPELIdVNZUI
1 .+3 .-
1 0 . N o
P in
5 .-R e s e t
Sw i t c hH D DL ED
Po w e rSw i t c hPo w e rL ED
7 .+9 . R e s e r v e
d
8 .-6 .+4 .-2 .+
JFP1
1. G r o u n d3 . S u s p e n d
L ED
5 . P o w e r
L ED
7 . N oP in
8 .+6 .-4 .+2 .-
B u z z e rSp e a k e r
JFP2
 Important
On the connectors coming from the case, pins marked by small triangles are positive wires. Please use the diagrams above and the writing on the optional M-Connectors to determine correct connector orientation and placement. 
The majority of the computer case’s front panel connectors will primarily be plugged into JFP1. 
•
• 
						

							
Chapter 1
1-25Getting Started

JUSB1~2: USB 2.0 Expansion Connectors
This connector is designed for connecting high-speed USB peripherals such as USB HDDs, digital cameras, MP3 players, printers, modems, and many others.
1.VCC
3.USB0-
10.N C
5.USB0+
7.Ground
9.No Pin
8.Ground
6.USB1+4.USB1-2.VCC
 Important
Note that the VCC and GND pins must be connected correctly to avoid possible damage.
JUSB3: USB 3.0 Expansion Connector
The USB 3.0 port is backwards compatible with USB 2.0 devices. It supports data transfer rates up to 5Gbits/s (SuperSpeed).
5 .US B 3 _ T X _ C _ D N4. G r o u n d3 . U S B 3 _ R X _ D P2 . U S B 3 _ R X _ D N1 . P o w e r
1 0 . G r o u n d9 .
+
US B 2 . 08 .
-
US B 2 . 07. G r o u n d6 . U S B 3 _ T X _ C _ D P
2 0 . N oP in1 9 . P o w e r1 8 . U S B 3 _ R X _ D N1 7 . U S B 3 _ R X _ D P1 6 . G r o u n d1 5 . U S B 3 _ T X _ C _ D N1 4 . U S B 3 _ T X _ C _ D P1 3 . G r o u n d1 2 . U S B 2 . 0
-
11. +US B 2 . 0
 Important
Note that the VCC and GND pins must be connected correctly to avoid possible damage.  
To use a USB 3.0 device, you must connect the device to a USB 3.0 port through an optional USB 3.0 compliant cable.
•
• 
						

							
Chapter 1
1-26Getting Started

JCI1: Chassis Intrusion Connector
This connector connects to the chassis intrusion switch cable. If the computer case is opened, the chassis intrusion mechanism will be activated. The system will record this intrusion and a warning message will flash on screen. To clear the warning, you must enter the BIOS utility and clear the record.
2.CINTRU
1.Ground
JAUD1: Front Panel Audio Connector
This connector allows you to connect the front audio panel located on your computer case. This connector is compliant with the Intel® Front Panel I/O Connectivity Design Guide.
1 . M IC L
3 . M IC R
1 0 . H e a d
Ph o n eD e t e c t i o n
5 . H e a d
Ph o n eR
7 . S E N S E _ S E N
D
9 . H e a d
Ph o n eL
8 . N oP in6 . M IC De t e c t i o n4 . N C2. G r o u n d