Namco Gun Survivor 2 Service Manual

Page 31
4. MOVING THE MACHINE
This equipment is fitted with castors to make it easier to move. Take care when
moving the equipment on an inclined floor.
The overall height of this equipment is 2180mm. Take care of any overhead
obstructions. (e.g. Light Fittings, Electric Cables etc.)
WARNING • NEVER turn the power to the machine ON until installationhas been completed.
WARNING • In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected...

Page 32

DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit
Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an
Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger...

Page 33




DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje,
nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.
6. La macchina non deve essere...

Page 34


 	
ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS
INTERIORES APENAS
NÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-
1. Exteriores.
2. `Luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de
água perto de ar condicionados ou equipamentos calorificos e locais com temperaturas
excessivamente quentes ou frias.
3. Locais aonde ficaria colocada no caminho de saidas de emergência ou equipamentos
extintores de fogo.
4. Locais estruturalmente instaveis ou locais com...

Page 35 5-1 Fitting the Seat Assy to the Monitor Cabinet
1. Fit the Joint Brackets, finger tight, to the Gun Cabinet with 2off(ea) hex head
screw (M10x30)
2. Place the Gun Cabinet up to the Monitor Cabinet and connect the
connectors.
3. Fit 2off (ea) hex head screws (M10x30) to retain the Joint Brackets to the
Monitor Cabinet.
4. Tighten fully all hex head screws (M10x30)
Joint Bracket
Gun CabinetJoint Bracket
Hex head screw (M10x30)
Hex head screw (M10x30)
  Joint BracketMonitor Cabinet
Connectors
Joint...

Page 36 5. Remove 4off security screw (M6x20) and remove the Gun Cabinet Rear Access
Door.
6. Fit 2off (1each side) hex head screrw (M10 x50), with flat washer.
7. Refit the Rear Access Doors.
Security screw (M6x20)
Rear Access
Door
Security screw (M6x20)
Hex head screw (M10x50)
Flat washer (M10) 

Page 37 5-2 Fitting the Header Display Panel
1. Slide the Header Display Panel down into the Grooves in the Monitor Cabinet.
2. Fit 3off security screw (M4x15), with flat washer.
GrooveHeader Display Panel
Header Display Panel
Monitor Cabinet
Security Wrench
Security screw (M4x15)
Flat washer 

Page 38 5-3 Adjusting the Level Adjusters
1. When the Monitor Cabinet is in it’s final installation position, lower the four (4)
Level Adjusters with a spanner so that all castors are raised from the floor by
approx 5mm. Tighten the lock nuts with a spanner to ensure that the Level
Adjusters do not move.
Note: If the location site of this game has a polished floor, it is recommended that
rubber pads are fitted under the Level Adjuisters to prevent the game sliding on
the floor when in use.
Adjustable...

Page 39
6 ADJUSTMENTS
  
Adjustment or maintenance on this machine should be carried out by
qualified personnel only.
  
Einstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.
  
Justeringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
  
Los ajustes y el mantenimiento de esta máquina deben ser realizados sólo
por personal cualificado.
  
L’installation, le service, le réglage, ou la maintenance...

Page 40
6-1 Adjustment Switches
The Adjustment switches are located inside the coin door.
1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings. (Refer to
section 6-2 Test Mode page 41)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test and...