Namco Gunmen Wars Service Manual

Operators Manual
IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY
AT
 ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL
ARE
 FOLLOWED PRECISELY.
Part No. 90500054
GUNMEN WARS 

PORTABLE APPLIANCE TESTING
Please Note:
During testing of the machine with a portable appliance tester the insulation test will
show a failure due to the fitting of two VDRs between Live/Earth and Neutral/Earth.
These components have been fitted to safeguard against high voltage surges that may
occur on the mains supply to the machine and to comply with the EMC regulations.
To conduct an insulation test on this machine, the VDRs must be isolated from the
circuit first.
Ensure that the 
VDRs are...

SAFETY WARNING
Gun Replacement or Maintenance.
To maintain compliance with CE regulations, the following
must be strictly adhered to.
When replacing the gun assembly or refitting the gun sides after maintenance, the four
screws located on the gun grip 
must be Nylon Countersunk Head Screws (M4x12), and
the Gun Grip Decals (L & R) 
must be fitted after the screws have been fully tightened.
Spare screws and decals are supplied with the machine at the time of delivery and
must be kept in the machine and...

No  part  of  this  publication  may  be  reproduced  by  any  mechanical,  photographic  or  electronic  process,  or  in  the  form  of
phonographic  recording,  nor  may  it  be  stored  in  a  retrieval  system,  transmitted  or  otherwise  copied  for  private  or  public  use, without
permission  from NAMCO  EUROPE  LIMITED.
While the information contained in this manual is given in good faith and was accurate at the time of printing.
NAMCO  EUROPE  LIMITED reserve  the  right  to  make  changes...

MOVING THE MACHINE
This  machine  is  fitted  with  castors  to  make  it  easier  to  move. Take  care  when  moving  the  machine  on  an
inclined  surface.
The  Header  Assembly  has  a  forward  centre  of  gravity,  so  it  is  important  that  at  least two  people  are  used
to  fit  or  remove  the  Header  Assembly.
The  fitting  position  of  the  Header  Assembly  is  high,  and  it  is  important    that  a  means  of  reaching  the
height  safely,without  stretching,  is  available.  (e.g....

Dieses  Dokument  darf  in  keiner Weise  vervielfältigt  werden.  Jegliche Tonaufnahmen  sowie  die  Speicherung  auf  Datenträger
(Suchsysteme),  die  Weitergabe  oder  sonstiges  Kopieren  für  den  gewerblichen  und  privaten  Gebrauch  sind  untersagt  und
bedürfen  der  vorherigen  Genehmigung  durch  NAMCO  EUROPE  LIMITED.
Die  informationen  in  diesem  Handbuch  entsprechen  den Tatsachen  bei  Drucklegung.  NAMCO  EUROPE  LIMITED  behält  sich
jedoch  das  Recht  zu  Änderungen  ohne...

HINWEISE  ZUR  AUFSTELLUNG
NIEMALS  das  Gerät  einschalten  bevor  die  Aufstellung  völlig
abgeschlossen  ist.
Zur  Vermeidung  von  Elektroschlägen  muß  das  Gerät  mit  einem
ordnungsgemäß  geerdetem  Netzstecker  an  die  Stromversorgung
angeschlossen  werden.
Um  zu  vermeiden,  daß  Kunden  durch  die  Gerätebewegungen
verletzt  werden,  muß  ein  Sicherheitsabstand  zu  anderen  Geräten
und  Wänden  von  mindestens  50cm  eingehalten  werden.
Zur  Vermeidung  von  Beschädigungen  durch...


Denne  udgivelse  må  ikke  reproduceres  af  nogen  som  helst  mekanisk,  fotografisk  eller  elektrornisk  proces  eller  i
form  af  indspilning,  den  må  heller  ikke  lagres  i  et  eftersøgningssystem  transmitteres  eller  kopieres  til  nogen  form  for
offentlig  benyttelse  uden  tilladelse  fra Namco  Europe  Limited.
Da  informationerne  i  denne  manual  er  givet  med  god  tro  og  var  korrekt  på  udskivningstidspunktet,
forbeholder  Namco  Europe  Limited  sig  retten  til,  at...

PUNKTER  OM  INSTALLATION
Tænd  aldrig  for  strømmen  til  maskinen  før  installering  er  fuldført.
For  at  undgå  mulige  elektriske  stød  sikres,  at  maskinen  er  forbundet
til  hovedstrømmen  med  sikkert  monterede  jordstik.
For  at  kunder  ikke  kommer  til  skade  ved  spillets  bevægelser  sikres,
at  der  er  mindst  50cm  afstand  til  andre  maskiner  og  vægge.
For  at  undgå  skader  på  maskinen  p.g.a.  fejlbetjening  sikres,  at
spændingen  på  hovedstrømmen  er  230  volt  AC....

No  se  permite  la  reproducción  total  ni  parcial  de  esta  publicación  por  ningún  medio  mecánico,  fotográfico  o
electrónico,  grabaciones  fonográficas,  ni  su  almacenamiento  informático,  su  transmisión  o  su  copia,  ya  sea  para
uso  público  o  privado,  sin  permiso  de  NAMCO  EUROPE  LIMITED.
Si  bien  la  información  contenida  en  este  manual  se  da  de  buena  fe  y  es  correcta  en  el  momento  de  su  impresión,
NAMCO  EUROPE  LIMITED  se  reserva  el  derecho  de...