Namco World Kicks Operators Manual

							Page 41
Monitor Cabinet
Hex head screw
(M6x20)
with spring washerConnectors Hex head screw
(M6x20)
With spring washer
Kicker cabinet
5. Place the Kicker Cabinet close to the Monitor Cabinet and connect the
connectors.
6 . Push the Kicker Cabinet fully upto the Monitor Cabinet, taking care not to trap
any wires, and fit 4off hex head screws (M6x20), with spring washers. 
						

							Page 42 5-3 Adjusting the Level Adjusters
1. When the game is in it’s final position ensure that all level adjusters are fully up.
2. Place an Adjustable Feet Strip Holder under the monitor cabinet rear level
adjusters, front level adjusters, and kicker cabinet rear level adjusters.
Place an Adjustable Feet Round Holder under each of the kicker cabinet front
level adjusters.
3. Lower all adjustable feet, ensuring that they fit the rebates of the holders, with a
spanner so that the cabinets are level and all castors are raised from the floor by
approx.10mm. Tighten the lock nuts with a spanner to ensure that the level
adjusters do not move during game play.
Adjustable feet
strip holder
Adjustable feet
round holder
10mmAdjustable feet
strip holder Lock nut
Adjustable
foot
Adjustable feet
strip holder 
						

							Page 43
6 ADJUSTMENTS
  
Adjustment or maintenance on this machine should be carried out by
qualified personnel only.
  
Einstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.
  
Justeringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
  
Los ajustes y el mantenimiento de esta máquina deben ser realizados sólo
por personal cualificado.
  
L’installation, le service, le réglage, ou la maintenance doivent être
effectués uniquement par les personnes qualifiées.
  
Μετατρπές ή επιδιρθώσεις στα µη0ανήµατα πρέπει να γίννται µ/ν απ/
ευσιδτηµένα άτµα.
  
Regolazioni e manutenzione su questa macchina devono essere fatti solo
da personale specializzato.
  
Justering eller vedlikehold på denne maskinen skall bare utføres av
kvalifiserte personell.
  
Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te
worden door bekwaam personeel.
  
Afinações ou manutenção nesta maquina, deverão ser efectuadas sómente
por pessoal qualificado.
	 		 	
	Justeringar och underhåll på denna maskin skall endast utföras av
kvalificerad personal.

 

 


Tätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden omaava
henkilökunta. 
						

							Page 44
6-1 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.
2. Test Switch Slide the test switch ON to enter test mode. 
Test mode allows testing and the changing of game settings.  (Refer to section 6-2
 T est Mode  page 45)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test and to change settings with\
in a test.
COIN COUNTER
TEST SERVICE
ENTER
UP
SELECT DOWN 2 Amp Q/B 
(Coin Fuse)
PLAYER 1
PLAYER 2
SERVICE
ENTER
TEST 
						

							Page 45 6-2 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will be
displayed on the monitor.
2. Operating the Select Up / Down Switch will step through the tests. Select the test
required by pressing the Enter Switch.
3. Activate the test by pressing the Enter Switch. Select “EXIT” in each test to return
to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to return to
normal game mode.
The Test Switch must always be in the “OFF” position for normal game mode.
MENU
COIN OPTIONS ................................................ Used to set the price of play.
GAME OPTIONS ................................................ Used to set the game options.
I/O TEST ................................................ Used for testing switches,
communications (when fitted) and
initialization.
MONITOR TEST ................................................ Used for setting the monitor.
SOUND TEST ................................................ Used for setting the volume.
ADS DATA ................................................ Used to view bookkeeping.
OTHERS ................................................ Used for testing the PCB.
SELECT SW : CHOOSE ENTER SW : ENTER 
						

							Page 46 6-2-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost and
related settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the
Enter button.
3. Use the Select Up/Down switch to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure
that the Game Cost is set to 1 Coin 1 Credit.
COIN OPTIONS
[DEFAULT IN GREEN]
GAME COST1 COIN (S) 1 CREDIT ............................(a)
CONTINUE COST *11 COIN (S) 1 CREDIT ............................(b)
RETURN MATCH COST *11 COIN (S) 1 CREDIT ............................(c)
FREE PLAYOFF ............................(d)
EXIT
SELECT SW :CHOOSE ENTER SW : ENTER
m e t Ino i t p i r c s e Dte S y r o t c a F
t s o C e m a G ) a (9~ 1 e l b a t t e s - - - - - t i d e r C 1 r o f d e r i u q e r s n i o C
t i d e r C 1 n i o C 1
t s o C e u n i t n o C ) b (9~ 1 e l b a t t e s - - - - - t i d e r C 1 r o f d e r i u q e r s n i o C
t i d e r C 1 n i o C 1
t s o C h c t a M n r u t e R ) c (9~ 1 e l b a t t e s - - - - - t i d e r C 1 r o f d e r i u q e r s n i o C
t i d e r C 1 n i o C 1
y a l P e e r F ) d (n o t t u b t r a t s e h t g n i s s e r p y b s t r a t s e m a g N O o t t e s n e h W
s n i o c g n i t r e s n i h t i wF F O
Note: The Continue Cost and Return Match Cost cannot be set higher than the
standard Game Cost. 
						

							Page 47 GAME OPTIONS
[DEFAULT IN GREEN]
COMM BOARD NG ............................... (a)
COMMUNICATION OPTIONS ............................ (b)
(VS CPU MODE)
GAME TIME 90 (SEC) ............................ (c)
GOLDEN GOAL TIME 30 (SEC) ............................ (d)
GAME DIFFICULTY B (NORMAL) ............................ (e)
(VS PLAYER MODE)
GAME TIME 90 (SEC) ............................ (f)
GOLDEN GOAL TIME 30 (SEC) ............................ (g)
RETURN MATCH MODE OFF ............................ (h)
AUTO SCORE INITIALIZE ............................ (i)
SCORE RANKING INITIALIZE ............................ (j)
EXIT
SELECT SW :CHOOSE ENTER SW : ENTER
6-2-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the game settings.
The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the
Enter button.
3. Use the Select Up/Down switch to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu screen.
(a) Communication Check
This displays the communication status. (Only active when a Link Pcb and  a
Communication cable fitted. These items
are an optional extra.)
y a l p s i D n e e r c Ssu t a t S n o i t a c i n u m m o C
N O : K N I L
) T F E L ( 1 : S A K N I L) s t i n u d e k n i l l l a n o d e y a l p s i D ( l a m r o n n o i t a c i n u m m o C
" ) T H G I R ( 2 " r o " ) T F E L ( 1 " . d e y a l p s i d s i D I - U P C
F F O K N I Lno i t a r e p o e m a g e l g n i s r o F
G N K N I L
) T F E L ( 1 : S A K N I L. d e v i e c e r g n i e b a t a d t c e r r o c n i t u b , K O s g n i t t e s n o i t a c i n u m m o C
" ) T H G I R ( 2 " R O " ) T F E L ( 1 " . d e y a l p s i d s i D I - U P C
G N D R A O B M M O C.e v i t c e f e d r o g n i s s i m s i d r a o b n o i t a c i n u m m o C 
						

							Page 48 COMMUNICATIONS OPTIONS
[DEFAULT IN GREEN]
LINK : ON .......................................... (a)
LINK AS  : 1  (LEFT)
COMMUNICATION MODE ON .......................................... (b)
CPU ID 1 (LEFT) ................................. (c)
EXIT
SELECT SW :CHOOSE ENTER SW : ENTER
(b) Communications Options
This item is set when the communication cable is connected. (This is an optional
extra).
1. Select “COMMUNICATIONS OPTIONS” on the menu screen to set the
communication settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the
Enter button.
3. Use the Select Up/Down switch to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu screen.
When setting the communication settings, set (b) “COMMUNICATION MODE” to ON
and (c) “CPU ID” to “1 (LEFT)” or “2 (RIGHT)” on each game respectively.
Note: Communication is not possible if “CPU ID” values are the same.
After setting the (a) and (b) settings on each game, select “EXIT” on both games. This
switches to the “NEGOTIATING screen” and synchronises communication.
Note: Switch each game to “EXIT” within thirty seconds of each other.
If communication is not synchronized during the countdown (30 seconds), the
communication status will revert to “LINK OFF” and the communication
settings will not be set. 
						

							Page 49 Settings for items (c) to (j)
m e t Ino i t p i r c s e Dte s y r o t c a F
e d o m U P C - e m i T e m a G ) c (0 0 3 , 0 4 2 , 0 8 1 , 0 5 1 , 0 2 1 , 0 9 , 0 6 , 0 3 . s d n o c e s n i e m i t e m a G
0 9
e d o m U P C - e m i T l a o G n e d l o G ) d (T I M I L O N , F F O , 0 9 , 0 6 , 0 3 , 5 1 e m i T l a o G n e d l o G d e d n e t x E
0 3
e d o m U P C - y t l u c i f f i D e m a G ) e () D R A H Y R E V D - Y S A E A ( D , C , B , A
L A M R O N ; B
e d o m r e y a l P - e m i T e m a G ) f (0 0 3 , 0 4 2 , 0 8 1 , 0 5 1 , 0 2 1 , 0 9 , 0 6 , 0 3 . s d n o c e s n i e m i t e m a G
0 9
e d o m r e y a l P - e m i T l a o G n e d l o G ) g (T I M I L O N , F F O , 0 9 , 0 6 , 0 3 , 5 1 e m i T l a o G n e d l o G d e d n e t x E
0 3
* g n i t t e s h c t a M n r u t e R ) h (FF O , N O
N O
n O r e w o P t a t e s e r - o t u a e r o c S h g i H ) i (FF O , N O
F F O
t e s e r g n i k n a R / e r o c S ) j (n w o D / p U t c e l e S e h t e s u n o i t p o s i h t g n i t c e l e s r e t f A
s s e r p d n a ) t e s e r o n ( O N r o ) t e s e r ( S E Y e s o o h c o t h c t i w s
. e t a v i t c a o t n o t t u B r e t n E e h t
(*) RETURN MATCH MODE cannot be changed from OFF when the communication
setting is at ON. 
						

							Page 50I/O TEST
LINK : ON ....................................... (a) 
LINK AS : 1  (LEFT) ....................................... (b)
I/O PCB CHECK ....................................... (c)
HOW TO [I/F INITIALIZE] ....................................... (d)
SWITCH TEST ....................................... (e) 
EXIT
SELECT SW :CHOOSE ENTER SW : ENTER
I/O TEST
LINK ON 
LINK AS 1  (LEFT)
I/O PCB CHECK 
I/O PCB connect OK ............................ (
*
)
EXIT 
SELECT SW :CHOOSE ENTER SW : ENTER
6-2-3 I/O Test 1. Select “I/O TEST” on the menu screen to check I/O PCB and Switches. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the\
 Enter button.
3. Use the Select Up/Down switch to change the setting. 
4. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a)  Communication Check. -----  (See page 47)
(b)  PCB Communication No ----  (See page 48)
(c) I/O PCB Check. When selected the following screen is displayed.
(
*
) “connect NG” is displayed if the I/O board is not connected.