NEC Applications Manager Installation Manual

NDA-30025   Revision 4.0Page 15
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
Step 7: Perform a Destructive Disk Scan
1. As another level of verification, perform a destructive disk scan when the menu 
appears by typing a 2 and pressing Enter:
The following menu displays:
2. Select a scan of the entire UNIX partition by typing 1 and pressing Enter.
The following menu appears:
3. Type 2 and press Enter to select a thorough scan.
The message “Do you want this to be a destructive scan?...

Page 16NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
Step 11: Make Manual Adjustments to the Filesystems
The hard disk has been initialized, and it is now time to allocate the recommended 
filesystems. You will need to change initial filesystem names, set the create 
filesystem flag to “yes”, and modify the First and Last block counts for some of the 
table entries, using the instructions below. The following values are recommended 
for the Application Manager....

NDA-30025   Revision 4.0Page 17
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
2. To create or rename a division, type n and press Enter.
3. Select a division to rename (0-7) and press Enter. (The division numbers are 
located in the # column of the allocation table, as illustrated in Figure 3-2.)
4. At the “What do you want to call it?” prompt, type the name of the division and 
press Enter.
Repeat this process (steps 1 through 4) for each of the following division names:
root
swap...

Page 18NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
Step 12: Provide Remainder of Installation Media
After you complete the adjustments to the filesystems, the following menu appears:
To install the remainder of the installation media:
1. Type i and press Enter.
The Product Medium Selection menu displays, as illustrated below:
2. Type the number that corresponds to the type of media you are using to install 
the product and press Enter. If you are using floppy...

NDA-30025   Revision 4.0Page 19
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
Step 13: Enter Serial Number and Activation Key
A prompt requests the unique serial number and activation key. These values are 
supplied on a card with the original SCO manufacturer’s documentation. (This card 
should be stored in a secure location after the operating system installation is 
completed.) At the start of this sequence, enter the serial number at the prompt and 
press Enter, as shown:
Enter your...

Page 20NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
2. Select the Install option using the arrow keys and press Enter. (Install is 
highlighted when it is selected.)
The following menu displays:
3. Select SCO UNIX System V Operating System using the arrow keys and 
press Enter.
The following menu appears:
4. Select Entire Product using the arrow keys and press Enter.
5. At the prompt, insert the SCO UNIX Extended Utility Floppy Volume X1 
diskette and press...

NDA-30025   Revision 4.0Page 21
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
7. Type y and press Enter.
8. Type a name unique to your site and press Enter.
9. At the prompt, press Enter to continue.
The following menu displays:
10. Press Enter.
The Custom menu redisplays.
11. Using the arrow keys, select Quit and press Enter.
12. Press Enter again while Ye s is highlighted to exit.
Step 16: Select Relaxed System Security
It is now necessary to decide on the desired level of security for...

Page 22NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
Step 17: Continue Installation
After selecting a security type, the following menu displays:
1. Type 2 and press Enter.
2. Continue with the root password assignment described in the next section.
Step 18: Enter Root Password
In this step, the system prompts you to enter a password with the following menu:
1. Type 1 and press Enter.
2. At the prompt, type a password and press Enter.
3. Re-enter the password at...

NDA-30025   Revision 4.0Page 23
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
Adding Drivers to UNIX
If any specific boards or drivers are required by the system or application, custom 
or installpkg are used to install the new drivers. 
1. From the “Boot:” prompt, press Enter.
2. Type your user password and press Enter.
The “#” prompt appears.
Parallel I/O DeviceThe parallel I/O device is used by the printer on the OAI system. To install the 
parallel port issue the following command:
1....

Page 24NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
Second Serial I/O 
Device1. At the “#” prompt, type mkdev serial and press Enter.
The following screen appears:
2. Type i and press Enter.
The following screen appears:
3. Select the number corresponding to the port card to be added and press Enter.
4. Select the COM port for the device and press Enter.
5. Type the number that corresponds to the card you are using and press Enter. 
(Quadram and IBM-COM2 cards...