NEC Applications Manager Installation Manual

							NDA-30025   Revision 4.0Page 25
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
SCSI Adapter 
DeviceInstalling a SCSI adapter device may require custom or installpkg. 
Note:
This is an example of the 7800 SCSI adapter using the installpkg
 command.
1. At the “#” prompt, type installpkg and press Enter.
2. Insert the SCSI Device Driver Floppy Disk (7800 Family Manager for SCO 
UNIX) and press Enter.
If the program installation requires more than one floppy disk, be sure to insert 
the disks in the proper order, starting with disk number 1.
3. A prompt displays the packages that are on the disk. Type the name of the 
package you want to install (e.g. alad) and press Enter.
SCSI Tape DeviceAfter installing the SCSI adapter, you can install a SCSI tape drive. To install any 
tape devices use the mkdev tape command.
Note:
This example will install a SCSI tape device.
1. At the “#” prompt, type mkdev tape and press Enter.
The Tape Drive Configuration Program menu appears, as illustrated below:
2. Type 1 and press Enter.
The Tape Drive Installation Menu appears, as illustrated below:
DQ`U 4bYfU 3_^VYWebQdY_^ @b_WbQ]
!9^cdQ\\ Q DQ`U 4bYfU
BU]_fU Q DQ`U 4bYfU
#3XQ^WU TUVQe\d DQ`U 4bYfU
CU\USd Q^ _`dY_^ _b U^dUb a d_ aeYd*
DQ`U 4bYfU 9^cdQ\\QdY_^ =U^e
!9^cdQ\\ 3QbdbYTWU DQ`U 4bYfU
9^cdQ\\ =Y^Y3QbdbYTWU DQ`U 4bYfU
#9^cdQ\\ AYS$ _b AYS( DQ`U 4bYfU
$9^cdQ\\ C3C9 DQ`U 4bYfU
CU\USd Q^ _`dY_^ _b U^dUb a d_ bUdeb^ d_ dXU ]QY^ ]U^e* 
						

							Page 26NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
3. Select the tape drive you want to install and press Enter. (In this example, type 
4 and press Enter.)
The following menu appears:
4. Select the appropriate drive (e.g., 1), and press Enter.
5. At the “Do you wish to configure the SCSI Cartridge Tape Drive now? (y/n)” 
prompt, type y and press Enter.
6. Enter the prefix of the SCSI host adapter by typing alad and pressing Enter.
7. At the “Which ‘alad’ SCSI hot adapter supports this device?” prompt, type 0 
and press Enter.
8. Enter the Target ID for the device by typing 2 or pressing Enter.
9. Enter the LUN of the device by typing 0 and pressing Enter.
10. At the “Update SCSI configuration? (y/n)” prompt, type y and press Enter.
11. At the prompt, press Enter to continue.
12. To leave the current string, type q and press Enter.
The Tape Drive Configuration Program menu displays.
13. Type q and press Enter.
14. At the “Do you wish to create a new kernel now? (y/n)” prompt, type n and 
press Enter.
C3C9 DQ`U 4bYfU 9^cdQ\\QdY_^ =U^e
! 9^cdQ\\ C3C9 3QbdbYTWU DQ`U 4bYfU
 9^cdQ\\ C3C9 5hQRidU DQ`U 4bYfU
# 9^cdQ\\ C3C9 )DbQS[ DQ`U 4bYfU
$ 9^cdQ\\ C3C9 41D 4bYfU
% 9^cdQ\\ 3_]`Qa C3C9 DQ`U 4bYfU
CU\USd Q^ _`dY_^ _b U^dUb a d_ bUdeb^ d_ dXU ]QY^ ]U^e* 
						

							NDA-30025   Revision 4.0Page 27
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
3C509 Ethernet 
DeviceUse the following steps to install an ethernet driver for the 3C509 ethernet board.
1. At the “#” prompt, type custom and press Enter.
The following menu displays:
2. Select the Install option using the arrow keys and press Enter. (Install is 
highlighted when it is selected.)
The following menu displays:
3ecd_]
C3? E>9H CicdU] F ?`UbQdY^W CicdU]
9^cdQ\\BU]_fU Ug @b_TeSd
C3? E>9H CicdU] F ?`UbQdY^W CicdU] 
						

							Page 28NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
3. Select A New Product using the arrow keys and press Enter.
The following menu appears:
4. Select Entire Product using the arrow keys and press Enter.
5. At the prompt, insert the 3C509 Ethernet III Driver Floppy diskette and press 
Enter.
6. Press Enter at the prompt to continue the installation.
7. After the installation is complete, press Enter to continue.
9^cdQ\\ /GUT^UcTQi ?Sd_RUb ) !))& #*#) 9^cdQ\\ dXU S_]`\UdU TYcdbYRedY_^9^cdQ\\
3X__cU Q^ _`dY_^*
5^dYbU @b_TeSd@QS[QWUc 6Y\Uc 
						

							NDA-30025   Revision 4.0Page 29
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
TCP/IP Runtime 
SystemUse the following steps to install the TCP/IP Runtime System.
1. At the “#” prompt, type custom and press Enter.
The following menu displays:
2. Select the Install option using the arrow keys and press Enter. (Install is 
highlighted when it is selected.)
The following menu displays:
3ecd_]
C3? E>9H CicdU] F ?`UbQdY^W CicdU]
9^cdQ\\BU]_fU Ug @b_TeSd
C3? E>9H CicdU] F ?`UbQdY^W CicdU] 
						

							Page 30NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
3. Select A New Product using the arrow keys and press Enter.
The following menu appears:
4. Select Entire Product using the arrow keys and press Enter.
5. At the prompt, insert the SCO TCP/IP Runtime Floppy Disk Volume 1 diskette 
and press Enter.
6. Press Enter at the prompt to continue the installation.
7. Continue this process, inserting the appropriate diskettes when prompted.
8. When prompted, use the serial number and activation key included with the 
SCO TCP/IP Runtime System distribution to enter the serial number and 
activation key. The serial number can be found on the SCO Product Activation 
Key Card in the Read This First booklet.
9. At the “Enter the system node name” prompt, press Enter.
10. Type the domain name for the node and press Enter.
The following screen appears:
11. Press Enter.
12. At the “Do you want to relink the kernel now?” prompt, type n and press Enter.
13. At the prompt, press Enter to continue.
Note:Make sure that you remove the SCO TCP/IP Runtime Disk Volume 3 from the 
floppy disk drive.
9^cdQ\\ /GUT^UcTQi ?Sd_RUb ) !))& #*#) 9^cdQ\\ dXU S_]`\UdU TYcdbYRedY_^9^cdQ\\
3X__cU Q^ _`dY_^*
5^dYbU @b_TeSd@QS[QWUc 6Y\Uc
%& D3@ S_^^USdY_^c SebbU^d\i S_^VYWebUT T_ i_e gQ^d d_*
! 1TT D3@ 3_^^USdY_^c
 BU]_fU D3@ 3_^^USdY_^c
CU\USd Q^ _`dY_^ _b U^dUb a d_ aeYd KaM* 
						

							NDA-30025   Revision 4.0Page 31
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
LLI DriversUse the following steps to install the LLI Drivers which are needed to configure 
network drivers into the kernel.
1. At the “#” prompt, type custom and press Enter.
The following menu displays:
2. Select the Install option using the arrow keys and press Enter. (Install is 
highlighted when it is selected.)
The following menu displays:
3ecd_]
C3? E>9H CicdU] F ?`UbQdY^W CicdU]
9^cdQ\\BU]_fU Ug @b_TeSd
C3? E>9H CicdU] F ?`UbQdY^W CicdU]
C3? D3@9@ Be^dY]U CicdU] 
						

							Page 32NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
3. Select A New Product using the arrow keys and press Enter.
The following menu appears:
4. Select Entire Product using the arrow keys and press Enter.
5. At the prompt, insert the SCO LLI Floppy Disk Volume 1 diskette and press 
Enter.
6. Press Enter at the prompt to continue the installation.
7. When the installation is complete, press Enter to continue.
8. Using the arrow keys, select Quit and press Enter.
9. Press Enter again while Ye s is highlighted to exit.
10. Remove the SCO LLI Floppy Disk Volume 1 from the floppy disk drive.
9^cdQ\\ /GUT^UcTQi ?Sd_RUb ) !))& #*#) 9^cdQ\\ dXU S_]`\UdU TYcdbYRedY_^9^cdQ\\
3X__cU Q^ _`dY_^*
5^dYbU @b_TeSd@QS[QWUc 6Y\Uc 
						

							NDA-30025   Revision 4.0Page 33
APM System Installation Manual SCO UNIX SYSTEM V INSTALLATION
Network 
ConfigurationAt this point, you need to configure the TCP/IP.
1. At the “#” prompt, type netconfig and press Enter.
The following screen displays:
2. Type 1 and press Enter.
3. Select the top level of the chain to add and press Enter.
4. Select the next level of chain to add and press Enter.
5. Confirm your selection by typing y and pressing Enter.
Note:
The setup procedure for the 3Com EtherLink III adapter is dependent on whether 
it is an ISA bus adapter (3C509), an EISA bus adapter (3C579), an MCA bus 
adapter (3C529), or a PCMCIA bus adapter (3C589). You must know which 
EtherLink III adapter type you have in order to configure the adapter correctly.
6. Type the appropriate information for the adapter type you are using at the 
prompts, pressing Enter after each entry.
Note:
For each ISA bus adapter, there are three parameters which you may need to 
supply: the Interrupt Request Level, the I/O Base Address, and the Transceiver 
Type. However, because the adapter can be configured automatically, you can 
choose not to specify configuration parameters and let them be chosen for you. 
An available Interrupt Request Level and I/O Base Address will be selected, and 
the driver will automatically select the transceiver based on which connector the 
network is attached to. If you wish to automatically configure the adapter, answer 
yes at the next prompt.
7. After you verify the Interface Address, Netmask, and Broadcast Address 
information, the following screen appears:
8. Type 1 and press Enter.
1fQY\QR\U _`dY_^c*
!1TT Q SXQY^
BU]_fU Q SXQY^
#BUS_^VYWebU Q^ U\U]U^d Y^ Q SXQY^
aAeYd
CU\USd _`dY_^*
 @cUeT_ ddic QbU SebbU^d\i S_^VYWebUT T_ i_e gQ^d d_*
!1TT @cUeT_ ddic
BU]_fU @cUeT_ ddic
CU\USd Q^ _`dY_^ _b U^dUb a d_ aeYd KaM* 
						

							Page 34NDA-30025   Revision 4.0
SCO UNIX SYSTEM V INSTALLATION APM System Installation Manual
9. At the “How many additional pseduo ttys you want to be created” prompt, press 
Enter.
10. To exit the TCP Connections menu, type q and press Enter.
11. To exit the chain menu, type q and press Enter.
12. The system prompts you to relink the kernel. If there are no other drivers to be 
installed, type y and Enter to relink the kernel now. If there are other drivers to 
be installed (i.e. SunRiver Driver), type n and press Enter, and install the 
drivers as needed. After all of the drivers have been installed, relink the kernel 
and then reboot by typing shutdown -g0 -y -i0 and press Enter.