NEC E552, E462, E422, E322 Users Manual

English-9English-8
English
3� following procedures:
• Reorient or relocate the receiving display�
• Increase the separation between the equipment and display �
• Connect the equipment into a different outlet than the receiver �
• Consult your dealer or an experienced radio/display technician for assistance�
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal...

English-11English-10
Preparation
IMPORTANT: Do not apply pressure to the screen display area which may compromise the integrity of the display� The manufacturer’s warranty does not 
cover user abuse or improper installations�
Preparing Your LCD Display For Wall Mounting
We suggest that you keep your display at least 2�36 inches (60 mm) from the wall to prevent cable interference� Before mounting your display on the wall, you need to remove the base� For your safety, only mount with a UL listed wall mount...

English-11English-10
English
Attaching the Base
E322 / E422 / E462E552
1� Place the display face down on a soft and flat surface to prevent scratching and damage�
2� Carefully align the base to the stand and fasten the screws with a cross\
-head screwdriver�
CAUTION: The base of the stand is very heavy � Install with care to avoid injury such as dropping the base onto one's foot�
Place The Display On A Solid Surface
Ensure that the LCD display is placed in a position to allow free flow of air � Do...

English-13English-12
Battery Installation and Replacement
The remote control is powered by two 1�5V AAA batteries� To install or replace batteries:
1� Open the battery cover of the remote 
control by pushing and pulling it in the direction of the arrow�
2� Insert two new “AAA” size batteries for the remote control� When replacing old batteries, push them towards the springs and lift them out�
3� Match the batteries to the (+) and (-) marks in the battery compartment�
4� Insert the bottom of the battery,...

English-13English-12
English
Connect To The Power Source
The display should be installed close to an easily accessible power outl\
et� Fully insert the prongs into the power outlet socket� A loose connection may cause image degradation�
If there is power to the display, the front LED at the bottom of the display will be either blue or red� A blue LED means the display is powered on� A red LED means the display is in standby mode�
Power On/Off Your New LCD Display
Press the power key on the remote control...

English-15English-14
Source Connection Guide
 
®
AC POWER
E322/E422/E462
E322/E462E422
5
614
2
9
7
3
8
1 

English-15English-14
English
E552
AC POWER
6
7
5
4
8
921
1� HDMI – Connect the primary source for digital video such as a DVD multimedia player or set top box through this all digital connector�
2� RGB/AUDIO – Connect the video and audio cables from a computer here�
3� AV  – Connect the primary source for composite video devices, such as a VCR or video game� Use the white and red connectors to connect the external audio from the same source�
4� COMPONENT (Y-PbPr with Audio L/R) – Connect the primary...

English-17English-16
8� USB/SERVICE – Insert USB storage device to view photos and listen to the music� /This USB slot is for future software upgrades�
9� RS-232C – Input from external equipment such as a PC or AV control system in order to control RS-232C functions�
Once your AV device is connected, press the Source button on the remote 
control to select the relevant source to view� (ex: Press COMP button to select “Component” if you have connected a source to the Component input�)
RS-232C Port...

English-17English-16
English
Operating Instructions
1
23
56
4
7
5
6 1
34
2
7
E322/E422/E462 E552
Using The Side Panel Controls
1�VOL +Press to increase the volume�
Press this key to shift Right in the OSD menu�
2�VOL -Press to decrease the volume�
Press this key to shift Left in the OSD menu�
3�CH ▲/ Press to increase the channel number �
Press this key to shift up in the OSD menu�
4�CH ▼/ Press to decrease the channel number �
Press this key to shift down in the OSD menu�
5�MENUPress to open or exit the...

English-19English-18
Using The Remote Control
Power
Press to turn On/Off (standby) the power� (Note: To completely turn off the power, unplug the AC cord from the power outlet�)
TV
Press to choose ATSC/NTSC tuner source mode�
AV
Press to choose Composite source mode�
COMP
Press to choose Component source 
mode�
HDMI/PC
Press repeatedly to choose PC IN or HDMI source mode�
0 ─ 9 / - number
Press to enter the tuner channel number to select channel (Press ‘-’ to choose the sub-channel)�
PRE CH
Press to...