NEC Gt2150 Lcd Projector Users Manual

E – 31 REMOTE 1 Connector
Pin Configuration of Optional CTL-6010 Cable
REMOTE 1 connector
of the Switcher mini D-
sub 15 pin (female) REMOTE 1 connector of
the Projector mini D-sub
15 pin (female)
Shield (frame ground)
Pins without a number are open.
51423
10
11 12 13 14 156 978
This connector is used for either connecting the ISS-6020/ISS-6020G Switcher or a third
party external control device. When the Switcher is used, connect it with the optional control
cable (15-15 pin; 50 ft./16m; CTL-6010) to...

E – 32
When used in stand alone operation.
Pin No.
14
5
10
3
4,8,12,11SHORT/OPEN
SHORT
OPEN
SHORT
OPEN
SHORT
OPEN
SHORT
OPEN
FUNCTION
External control mode ON
External control mode OFF
POWER ON
POWER OFF
PICTURE MUTE ON
PICTURE MUTE OFF
MUTE SOUND ON
MUTE SOUND OFF
* When the combinations other than specified in the above table are selected, the input will be forcefully
switched to RGB 1.
* The term “SHORT” means to connect with pin 15
* When in the external control mode, the POWER, Source/Alphanumeric,...

E – 33
PC CONTROLREMOTE2
OUT OUTIN IN
Operating Multiple Projector with Remote Control
You can operate multiple projectors with the same remote control in wireless operation.
To do so:
1. Select [Projector Options]→[Setup]→[Page 5]→[Projector ID] and assign an ID number to each projector. See
also page E-50.
2. On the remote control specify the ID number of the projector to be adjusted. Press and hold the CTL and press
MENU (ADDRESS) button to enter the ID number.
You can operate the projector assigned...

E – 34
PC CONTROL
OUTIN
PC CONTROL
OUTIN
L/MONO
L/MONO
RGB 2R R
OUTPUTANALOG
DVI DIGITAL
DVI DIGITAL
L/MONO
L/MONO
RGB 2R R
OUTPUTANALOG
DVI DIGITAL
DVI DIGITAL
Using the PC CONTROL connectors
The Link mode function allows you to adjust or set multiple projectors using the DVI DIGITAL OUTPUT and the PC
CONTROL connectors.
Connection for Double Stacking in Link Mode
Master projector
Bi-directional RS-232C
cable (not supplied)
Slave projectorDVI cable
(not supplied)
Connect source equipment to the master...

E – 35
5. OPERATION
This section describes how to select a computer or video source, ad-
just the picture and sound, edit a signal and adjust all other settings
and adjustments for proper projector set-up.
General Controls
Before you turn on the projector ensure that the computer or video
source is turned on and that the lens hood cap is removed.
1.Turn on the Projector
Plug the supplied power cable in the wall outlet. The projector
will go into its standby mode and the power indicator will glow
orange....

E – 36
Customizing Basic/Custom Menu
The Basic/Custom menu can be customized to meet your requirements.
Selecting a menu item from the “Basic/Custom Menu Edit” list, allows
you to custom tailor the menu items to your needs.
1. Select “Basic/Custom Menu Edit” to display the “Basic/Custom
Menu Edit” screen.
2. Use the 
 or  button to highlight your selection and press the
Enter button to place a check mark next to an option. This action
enables that feature.
Press the Enter button again to clear the check...

E – 37 List of Direct Button Combinations
CTL+  SOURCE  (1-10) Switches to any selected signal found in the Entry List.
To enable this combination, you must first assign specific remote buttons for direct input
selection in the Entry Edit window.
CTL+  ENTER (While  displaying  Entry  list) Displays the Entry Edit Command window.
CTL+CANCEL Returns  to  the previous menu without closing the slidebar or dialog.
CTL+  UNDO Clears all menus or adjustment/setting screens. All adjustments are saved...

E – 38 Menu tree
0 – 100
Normal / Natural 1 / Natural 2
Advanced Menu
Source Select
Adjust (Source)
Volume
Ref Adj
Factory Default
Projector Options
Help
Test Pattern
1. RGB1
2. RGB2
3. DVI (DIGITAL)
4. Video1
5. Video2
6. S-Video
7. RGB1 (VIDEO)
8. RGB1 (S-VIDEO)
Entry List
Switcher
Entry List When Switcher Control is
turned on:
StandaloneBrightness
Contrast
Saturation
Color
Hue
Sharpness
V-Aperture
Gamma Correction
Color Temperature
Brightness
Contrast
Signal Level
Pixel Adjust
Position
Aspect Ratio...

E – 39
Normal / EcoAdvanced Menu
Source Select
Adjust (Source)
Volume
Ref Adj
Factory Default
Projector Options
Help
Test Pattern
All Data / Current Signal
Including Entry List Keystone
Lamp Mode
Ref. White Bal.
Contents
Source Information
Projector Information
Brightness R/G/B, Contrast R/G/B
Standalone / Master / Slave
Standalone / SW 1 Level / SW 2 Level
Network Board / Default Gateway
Contents
Cross Hatch, Gray Bars
Black Raster, Gray Raster (25%)
Gray Raster (50%), White Raster
Red / Green / Blue...

E – 40 Menu windows or dialog boxes typically have the following elements:
Title bar: Indicates the menu title.
Highlight: Indicates the selected menu or item.
Solid triangle: Indicates further choices are available. A highlighted triangle indicates the item is active.
Tab: Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Radio button: Use this round button to select an option in a dialog box.
Check box: Place a checkmark in the square box to turn the...