NEC Gt5000 Lcd Projector Users Manual

							GT6000/GT5000
LCD Projector
User’s Manual 
						

							ii
Important Information
Precautions
Please read this manual carefully before using your NEC GT6000/
GT5000 Projector and keep the manual handy for future refer-
ence.
Your serial number is located on the bottom of your GT6000/
GT5000. Record it here:
If you are a user of the GT6000R, read the supplied document
which describes the differences from the GT6000.
CAUTION
To turn off main power, be sure to remove the plug
from power outlet.
The power outlet socket should be installed as near
to the equipment as possible, and should be easily
accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABI-
NET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SER-
VICE PERSONNEL.
This symbol warns the user that uninsulated volt-
age within the unit may be sufficient to cause elec-
trical shock. Therefore, it is dangerous to make any
kind of contact with any part inside of the unit.
This symbol alerts the user that important informa-
tion concerning the operation and maintenance of
this unit has been provided. The information should
be read carefully to avoid problems.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EX-
TENSION CORD OR IN AN OUTLET UNLESS ALL THREE
PRONGS CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE
COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY
QUALIFIED NEC SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Ca-
nadian Interference-Causing Equipment Regulations.
3. GSGV Acoustic Noise Information Ordinance:
The sound pressure level is less than 70 dB (A) according to ISO
3744 or ISO 7779.
In UK, a BS approved power cable with moulded plug has a Black
(five Amps) fuse installed for use with this equipment. If a power
cable is not supplied with this equipment please contact your
supplier.
• IBM is a registered trademark of International Business Machines Cor-
poration.
• Macintosh and PowerBook are registered trademarks of Apple Com-
puter, Inc.
• Other product and company names mentioned in this user's manual
may be the trademarks of their respective holders.
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified by
NEC Solutions, Inc. in this manual. Failure to comply with this
government regulation could void your right to operate this equip-
ment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed
all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from
dust and moisture. Tilting the front of the projector up or down by
more than 45° from level could reduce lamp life by up to 20%.
3. Do not place your projector in direct sunlight, near heaters or heat
radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal
components.
5. Handle your projector carefully. Do not hold the lens hood and the
terminal covers. Dropping or jarring can damage internal compo-
nents.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in or-
der to ensure proper operation and reduce the risk of bodily
injury.
c. In addition, the ceiling must be strong enough to support the
projector and the installation must be in accordance with any
local building codes.
d. Please consult your dealer for more information.
To Dealer or Installer:
To prevent the projector from falling, install it in a place and fasten it in
a way with sufficient strength to support the combined weight (26.0
kg/57.3 lbs) of the projector (18.4 kg/40.6 lbs), the lens (4.0 kg/8.8
lbs) and the ceiling mount(3.2 kg/7.1 lbs) for an extended period of
time as well as to withstand earthquakes. 
						

							iii
Power Supply
1. The projector is designed to operate on a power supply of 100-
120 or 200-240 V 50/60 Hz AC. Ensure that your power supply fits
this requirement before attempting to use your projector.
2. Handle the power cable carefully and avoid excessive bending. A
damaged cord can cause electric shock or fire.
3. If the projector is not to be used for an extended period of time,
disconnect the plug from the power outlet.
4. Do not touch the power plug with wet hand. Doing so can cause
electrical shock or fire.
5. Do not touch the power plug during a thunder storm. Doing so
can cause electrical shock or fire.
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,
use a mild detergent. Never use strong detergents or solvents such
as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to
scratch or mar the lens.
CAUTION
Do not unplug the power cable from the wall outlet under any one of
the following circumstances. Doing so can cause damage to the pro-
jector:
• While the message "Please wait a moment." appears. This mes-
sage will be displayed after the projector is turned off.
• Immediately after the power cable is plugged into the wall outlet
(the POWER indicator has not changed to a steady orange glow).
• Immediately after the cooling fan stops working (The cooling fan
continues to work for 90 seconds (2 minutes in the optional ex-
tended life lamp GT60LPS) after the projector is turned off with the
POWER button).
CAUTION
• Do not try to touch the ventilation outlets as they can become heated
while the projector is turned on.
• Do not put the projector on its side when the lamp is turned on.
Doing so may cause damage to the projector.
• Before shipping this projector, remove the lens and attach the lens
hood cap.
The Lens Shift mechanism may encounter damage caused by im-
proper handling during transportation.
• Do not eject a PC card or LAN card while its data is being ac-
cessed. Doing so can damage your PC card or LAN card.
Lamp Replacement
• To replace the lamp, follow all instructions provided on page 9-2.
• Be sure to replace the lamp when the message "The Lamp has
reached the end of its usable life. Please replace the lamp." ap-
pears. If you continue to use the lamp after the lamp has reached
the end of its usable life, the lamp bulb may shatter, and pieces of
glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury. If this happens, contact your NEC
dealer for lamp replacement.
• Allow a minimum of 90 seconds (2 minutes in the optional extended
life lamp GT60LPS) to elapse after turning off the projector. Then
turn off the main power and disconnect the power cable and allow
60 minutes to cool the projector before replacing the lamp.• The projector must be operated with two lamp housings installed
regardless of whether or not the lamp is active. Failure to do so
may degrade the performance of the projector such as screen flicker
or loss of lamp life. If one lamp has reached the end of its usable
life, replace it with a new one as soon as possible.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unob-
structed to prevent the build-up of heat inside your projector. Allow
at least 3 inches (10 cm) of space between your projector and a
wall. Allow at least 12 inches (30cm) of space between the outlets
on the left side (when viewed from the front) and the wall.
2. Prevent foreign objects such as paper clips and bits of paper from
falling into your projector. Do not attempt to retrieve any objects
that might fall into your projector. Do not insert any metal objects
such as a wire or screwdriver into your projector. If something should
fall into your projector, disconnect it immediately and have the ob-
ject removed by a qualified NEC service personnel.
3. Do not place any liquids on top of your projector.
4. When using a LAN cable:
For safety, do not connect to the connector for peripheral device
wiring that might have excessive Voltage.
CAUTION
• Do not look into the lens while the projector is on. Serious damage
to your eyes could result.
• Keep any items such as magnifying glass out of the light path of
the projector. The light being projected from the lens is extensive,
therefore any kind of abnormal objects that can redirect light com-
ing out of the lens, can cause unpredictable outcome such as fire
or injury to the eyes.
• Do not cover the lens with the supplied lens hood cap or equiva-
lent while the projector is on. Doing so can lead to melting of the
cap and possibly burning your hands due to the heat emitted from
the light output.
Important Information 
						

							iv
Table of Contents
1. Introduction
zWhat's in the Box? .................................................................... 1-2
x Introduction to the Projector ................................................... 1-3
c Getting to Know Your Projector ............................................... 1-4
Attaching the lens hood cap to the lens hood with the supplied
string and rivet ............................................................................ 1-6
Carrying the Projector ................................................................. 1-6
Top Features ............................................................................... 1-7
Terminal Panel Features ............................................................. 1-8
v Remote Control Features ....................................................... 1-10
Remote Control Precautions ..................................................... 1-12
Remote Control Battery Installation .......................................... 1-12
Operating Range for Wireless Remote Control ........................ 1-12
Using the Remote Control in Wired Operation ......................... 1-13
2. Installation
z Setting Up Your Projector ........................................................ 2-2
Screen Size and Projection Distance ......................................... 2-2
x Lens Shift Adjustable Range ................................................... 2-4
c Optional Lens Installation ....................................................... 2-6
v Making Connections .............................................................. 2-13
Connecting Your PC or Macintosh ............................................ 2-13
To connect Scart Output ........................................................... 2-14
Connecting an External Monitor ............................................... 2-14
Connecting Your DVD Player .................................................... 2-15
Connecting Your VCR or Laser Disc Player .............................. 2-16
Connecting to a Network .......................................................... 2-17
Connecting the Supplied Power Cable ..................................... 2-18
3. Projecting an Image (Basic Operation)
zTurning on the Projector .......................................................... 3-2
x Selecting a Source ................................................................... 3-3
c Adjusting the Picture Size and Position ................................. 3-3
v Correcting the Horizontal and Vertical Keystone Distortion (3D
Reform) ..................................................................................... 3-4
b Optimizing RGB Picture Automatically .................................. 3-6
nTurning Up or Down Volume .................................................... 3-6
mTurning off the Projector .......................................................... 3-7
4. Convenient Features
zTurning Off the Image and Sound ........................................... 4-2
x Enlarging and Moving a Picture .............................................. 4-2
c Getting the On-line Help and Information .............................. 4-2
v Using a USB Mouse ................................................................. 4-3
b Using a USB HUB Function ..................................................... 4-3
n Changing Background Logo ................................................... 4-4
m Making Freehand Drawings on
,Projected Image (ChalkBoard) ................................................ 4-4
.Lens Memory ............................................................................ 4-5
5. Using the Viewerz Making the Most out of the Viewer Function ......................... 5-2
x Operating the Viewer Function from the Projector
(playback) ................................................................................. 5-3
6. Using the Projector in a Networkz End User License Agreement ................................................. 6-2
x Introduction ............................................................................... 6-3
c Supported Projectors ............................................................... 6-4
v Equipment Connections and Settings .................................... 6-5
b Software Installation ................................................................ 6-6
n Starting/Exiting the Software .................................................. 6-7
mTroubleshooting ........................................................................ 6-8
7.Setting Up for Double Stacking in Link Mode
z Stacking and Connecting the Projectors ............................... 7-2
x Adjusting and Registering Signals to Be Projected .............. 7-5
c Adjusting the Lens Shift, Zoom and Focus to Clearly Display
all projected patterns .............................................................. 7-5
v Link Mode Setting .................................................................... 7-5
b List of Menu Items Available in Link Mode ............................ 7-6
8. Using On-Screen Menu
z Basic Menu Operation .............................................................. 8-2
x List of Direct Button Combinations ........................................ 8-3
c Menu tree ................................................................................... 8-4
v Menu Descriptions & Functions .............................................. 8-7
Adjust (Source) ........................................................................... 8-8
Picture ................................................................................. 8-8
Video Adjust ........................................................................ 8-8
Picture Management ........................................................... 8-9
Image Options ................................................................... 8-10
Option Adjust ..................................................................... 8-10
Lens Memory ..................................................................... 8-11
Signal Type ........................................................................ 8-11
Sound ....................................................................................... 8-11
Ref. Adjust ................................................................................ 8-12
Using 3D Reform ............................................................... 8-12
Screen Type ....................................................................... 8-12
Reference White Balance .................................................. 8-12
Reference Color Correction ............................................... 8-12
Reference Lens Memory ................................................... 8-13
Factory Default ......................................................................... 8-13
Projector Options ...................................................................... 8-13
Menu ................................................................................. 8-13
Setup ................................................................................. 8-15
Lamp Settings ................................................................... 8-18
Link Mode .......................................................................... 8-18
LAN Mode ......................................................................... 8-19
Seamless Switch (GT6000 only) ....................................... 8-23
Setting a Password ........................................................... 8-24
Security ............................................................................. 8-25
Tools ......................................................................................... 8-26
Timer................................................................................. 8-26
Using Capture (GT5000 only) ........................................... 8-28
Using PC Card Files .......................................................... 8-28
Using ChalkBoard ............................................................. 8-28
Help .......................................................................................... 8-28
Contents ............................................................................ 8-28
Source Information ............................................................ 8-28
Projector Information ......................................................... 8-29
Test Pattern ............................................................................... 8-29
9. Maintenancez Replacing the Lamp ......... 9-2
z Replacing or Cleaning the Filter ............................................. 9-3
x Cleaning the Cabinet and the Lens ......................................... 9-4
10. AppendixzUSB Memory Device or USB Memory Card Reader Support ........10-2
xTroubleshooting ...................................................................... 10-3
c Specifications ......................................................................... 10-6
v Cabinet Dimensions ............................................................... 10-8
b Pin Assignments of D-Sub RGB Input Connector ............... 10-8
n Compatible Input Signal List ................................................. 10-9
m REMOTE 1 Connector .......................................................... 10-10
, PC Control Codes and Cable Connection ..........................10-11
Cable Connection ...................................................................10-11
PC Control Connector (D-SUB 9P) .........................................10-11
. Using Software Keyboard ....................................................10-11
⁄0  Operation Using an HTTP Browser ..................................... 10-12 
						

							1
Introduction
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
zWhat's in the Box? .................................................... 1-2
x Introduction to the Projector ..................................... 1-3
c Getting to Know Your Projector ................................. 1-4
Attaching the lens hood cap to the lens hood with the supplied string and rivet . 1-6
Carrying the Projector ......................................................................................... 1-6
Top Features ........................................................................................................ 1-7
Terminal Panel Features ...................................................................................... 1-8
v Remote Control Features ....................................... 1-10
Remote Control Precautions ............................................................................. 1-12
Remote Control Battery Installation ................................................................... 1-12
Operating Range for Wireless Remote Control ................................................. 1-12
Using the Remote Control in Wired Operation .................................................. 1-13 
						

							1-2
z What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your Projector.
NOTE: Lenses are optional. Order lenses from your NEC dealer.
Power cable for Japan (AC 100V)
(7N080113)
Documents
(Japanese and English/German/French/
Italian/Spanish/Swedish)
1. Introduction
3D REFORM3
DA
S
E
L
E
C
T
LENS SHIFTF
O
C
U
SZ
O
O
MD
O
W
N L
E
F
TR
I
G
H
T U
PZSTATUS
PCCARD 2
PCCARD 1
LAMP 1
LAMP 2
POWERO
N
/
S
T
A
N
D
B
YAUTO ADJUSTMENUENTERCANCEL
F
Lens hood cap(24F37661)
Projector
Terminal cover
(Left and Right)
String 
(24C04541)and
rivet(24C04531)
Remote control (79646634) and
batteries (AAA
2)
Remote cable(7N520019)
Power cable for Europe (AC 230V)(7N080003)Power cable for North America (AC 120V)(7N080208)
Important
Information
User’s Manual(7N950194)User Supportware(7N950431) 
						

							1-3
x Introduction to the Projector
This chapter introduces you to the GT6000/GT5000 high end
fixed installation projector and describes key features and con-
trols.
Congratulations on Your Purchase of the GT6000/GT5000
projector
The GT6000/GT5000 is our most sophisticated three panel, dual
lamp XGA LCD projector.  With the GT6000/GT5000 you will be
able to project images up to 500" (measured diagonally) from
your DVD player, VCR, satellite hookup, HDTV source, PC, Work-
station or Macintosh computer (desktop or notebook) and im-
ages from you digital camera PC Card or compact flash memory.
The GT6000/GT5000 incorporates integrated networking access
through the RJ45 input or provides for wireless network connec-
tivity from an optional wireless network PC card.  With extensive
input and output panels, optional long life lamp, full suite of quick-
change lenses and a full function remote, the GT6000/GT5000
will let you immerse yourself in large screen viewing.
Features you’ll enjoy on the GT6000/GT5000:• Integrated RJ45 connector for wired networking ability
• Two optional modular card slots allow for future projector growth
with the ability to add additional input cards
• Dual PC card slots provide for optional wireless/wired network
connectivity or PC Card usage
• Email projector error status information to selected individuals
• Power Horizontal and Vertical lens shift for optical display cor-
rections
• Lens memory controls lens attributes (zoom, focus, shift) de-
pending on input resolution and input selected for fast and easy
source transitions
• NEC designed and developed SweetVision
TMtechnology for
enhanced video image display, more vibrant colors and blacks
richer with detail
• 3D Reform enhanced image technology for increased projec-
tor versatility that provides for horizontal, vertical and diagonal
keystone correction (allows for positioning the projector in off
center locations in the room and still get aligned images)
• Display 16:9 or 4:3 information and fill the screen
• HDTV (1080p, 1080i, 720p) and SDTV (576p, 576i, 480p, 480i)
compatibility
• GT5000 supports a native resolution of XGA (1024
768) and
GT6000 supports a native resolution of SXGA+ (1400
1050).
• Intelligent lamp technology offers up to six user lamp settings
to maximize light output or lamp life and provide for built in
redundancy
• Smart security settings for password protection, control panel
lock, menu lock and PC card protection key to help prevent
unauthorized access and adjustments to the projector
• Seamless Switch function provides a transition effect during
source switching (GT6000 only).
• ADA508 and Executive Order 13221 Federal Government com-
pliance *
1
• NEC 3D 10-bit video decoder for expanded black levels and
adaptive gamma correction
• High performance optional long life lamp for low total operat-
ing costs
• Digital photo viewer to display larger than life images from your
digital cameras PC card or compact flash card• Double stackable for built in redundancy and high light output
requirements
• Built in 5W
2 speakers for an integrated audio solution
• Two timer settings - On/Off with programming or Sleep timer
that counts down at selected intervals
• 12V low voltage Screen Trigger output
• Easy set up and operation
• Eco-mode™ lamp technology for increased lamp life and en-
ergy savings
• VORTEX Technology Plus™ for uncompromising display of
video and data.  Improves white level, color accuracy, dynamic
range, and display of varying levels of black in an image
• Wireless remote control operation
• External control via RS232, USB or Network
• NEC’s exclusive Advanced AccuBlend intelligent pixel blend-
ing technology provides for extremely accurate image com-
pression and HDTV (1920
1080) display resolution*
2.
• Supports most IBM VGA, SVGA, XGA, Macintosh, component
signal (YCbCr/YPbPr) or other RGB signals within a horizon-
tal frequency range of 15 to 100 kHz and a vertical frequency
range of 48 to 120 Hz. This includes NTSC, NTSC4.43, PAL,
PAL-M, PAL-N, PAL60 and SECAM standard video signals
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
NTSC4.43: TV standard used in Middle East countries.
PAL: TV standard used in Western Europe.
PAL-M: TV standard used in Brazil.
PAL-N:  TV standard used in Argentine, Paraguay and Uruguay.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
*1The GT5000 and GT6000 meet ADA508 compliance, the lat-
est American government regulation which provides for closed
captioning, including a menu system that can be viewed by
colorblind users. This model also meets Executive Order 13221
requirement for standby operation, which consumes less than
1 watt.
*
2HDTV 1080P (1920
1080), HDTV 1080i (1920
1080), HDTV
720 p (1280
720) and 1600
1200 are displayed with NECs
Advanced AccuBlend technology on the GT5000.
HDTV 1080P (1920
1080), HDTV 1080i (1920
1080) and
1600
1200 are displayed with NECs Advanced AccuBlend
technology on the GT6000.
1. Introduction 
						

							1-4
1. Introduction
AUDIO
A
U
D
IO
 O
U
T
R
R/Cr
G/Y
B/Cb
V
H/
  HV
RL/MONO
RL/MONORL/MONOL/MONO
DVI
R
G
B
O
U
T
R
GB 1R
GB 2AUDIOS
L
O
T
1S
L
O
T
2
VIDEOS-VIDEO
P
C
C
O
N
T
R
O
L
I
N
I
N O
U
T
O
U
T S
C
T
R
I
G
G
E
RR
E
M
O
T
E
2 R
E
M
O
T
E
1 L
A
N
A
C
I
N
U
S
B(MOUSE/HUB)U
S
B(P
C)P
C
C
A
R
D2
1
3D REFORM3D A
SELECT
LENS SHIFTFOCUS ZOOMDOWN LEFT RIGHTUPZ
STATUS
PC CARD 2
PC CARD 1
LAMP 1
LAMP 2
POWERO
N
/S
T
A
N
D
 B
YAUTO A
DJUST
MENUENTERCANCEL
F
c Getting to Know Your Projector
Controls
*NOTE: Slot for Kensington MicroSaver Security System
This security slot supports the MicroSaver® Security System.MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.Lens hood Terminal panel (Left)
AC INPUT
Connect the supplied
power cable’s three-pin
plug here. Lens (optional)
Lens hood capTerminal panel (Right)
Foot (four)
Rotate to fine-adjust the height of
each foot (max. 0.6”/15mm).Built-in Security Slot ( 
 )*
Remote sensorLamp cover 1 (Right)
Carrying handle
Speaker 5W (Stereo)Air filter (Right)
Attaching and Removing the Terminal Covers
To remove the terminal cover, push and hold the latch.
To attach the terminal cover, align the protrusions inside and push it until you feel it click into place.
12
A
U
D
I
O
A
U
D
I
OA
U
D
IO
 O
U
T
R
R
/
C
r
G
/
Y
B
/
C
b
V
H
/
H
V
RL
/M
O
N
O
RL
/M
O
N
ORL
/
M
O
N
O L
/
M
O
N
O
SLOT1
OPTION2DVIRGB OUT
RGB 1RGB 2VIDEOS-VIDEO
USBA
USB B
PCCARD
PCCONTROL
IN
IN OUT
OUT SC TRIGGER
REMOTE 2 REMOTE 1 LAN
AC IN
SOURCESAN/STAND BYA
U
T
O
A
D
J
U
S
T 
						

							1-5
USB (MOUSE/HUB)USB (PC)PC CARD1
2
PC CONTROL
IN
IN OUT
OUT SC TRIGGER REMOTE 2REMOTE 1LANAC IN 
AUDIO
AUDIO
AUDIO OUTR
R/Cr
G/Y
B/Cb
V
H/
  HVR
L/MONO
RL/MONORL/MONOL/MONO
SLOT 1 SLOT 2
DVI
RGB OUT
RGB 1
RGB 2
VIDEOS-VIDEO
3D REFORM3
DA
SELEC
T
LEN
S S
H
IF
TFOCU
SZOO
MDO
W
N LE
FTRIG
HT UPZ
STATUS
PC CARD 2
PC CARD 1
LAMP 1
LAMP 2POWERON/STAND BYAUTO ADJUST
MENUENTERCANCEL
F
Depression for foot (4 locations)
1. Introduction
Lamp cover 2 (Left)Remote sensor
Remote sensorSpeaker 5W (Stereo)
Ventilation (outlet)Ventilation (outlet)
Air filter (Right)
Ventilation (inlet) Remote sensor
Remote sensorAir filter (Left) 
						

							1-6
Attaching the lens hood cap to the lens hood with the supplied string and rivet
1. Thread the string through the hole on the lens hood cap.
Lens hood cap
String
2. Use the rivet to attach the string to the bottom of the projector.
AUDIO
AUDIO
AUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/HVR
L/MONO
RL/MONO
RL/MONOL/MONO
OPTION 1 OPTION 2
DVI
RGB OUT
RGB 1
RGB 2
VIDEOS-VIDEO
Rivet
3D REFORM3D A
SELECT
LENS SHIFT
FOCUS ZOOMDOWN LEFT RIGHTUP
Z
STATUS PC CARD 2 PC CARD 1 LAMP 1 LAMP 2 POWER
ON/STAND BYAUTO ADJUST
MENU
ENTERCANCEL
F
Carrying the Projector
Always carry your projector by the handle.
Ensure that the power cable and any other cables connecting to video sources are disconnected before moving the projector.
When moving the projector or when it is not in use, cover the lens with the lens hood cap.
CAUTION:Do not put the projector on its side when the lamp is on.Doing so may cause damage to the projector.
1. Introduction