NEC LT10 Projector User Manual

	



1. Power Cord
2. VGA Cable
3. S-Video Cable
4. Composite Video Cable
Connecting the Projector
™To ensure the projector works well with your computer, please
set the display mode of your graphics card is less than or equal to
1024 X 768 resolution. Make sure timing of the display mode is
compatible with the projector.  Refer to the “Compatibility
Modes” section on page 30.
S-Video Output
Video Output
 1
23
4
Installation 


Installation
Lens capOn/Standby
 1
2
Powering On the Projector
1.Remove the lens cap.n
2.Ensure that the power cord and signal cable are securely
connected.
3.Turn on the lamp by pressing “On/Standby” button on the
control panel. o
The startup screen will display for 20 seconds and the Power
indicator will flash green.
When the startup screen disappears, the Power indicator will
turn green.
4.Turn on your source (computer, notebook, video player ,
etc.).  The projector will detect your source...


Powering Off the Projector
1.Press the “Power” button to turn off the projector lamp.
2.After pressing the “Power” button, you will see a message
“Power off the lamp?” on the on-screen display. Press the
“Power” button again to confirm.
Otherwise the message will disappear after 5 seconds.
3.Power indicator flashes orange for about 100 seconds. The
projector will  automatically shut itself down.
If you want to turn on the projector again, you must press the
“Power” button after 100 seconds of...





Installation
Adjusting the Projected Image
Adjusting the Projector Height
Tilt Adjusted wheel
Adjustable Tilt
Foot
 1
2
3Adjustable Tilt
Foot Button
The projector is equipped with an adjustable tilt foot foot for
adjusting the projector height.
To raise the projector:
1.Press the adjustable tilt foot button 
n.
2.Raise the projector to the desired display angle o, then
release the button to lock the adjustable tilt foot into
position.
3.Use 
p to fine-tune the display angle.
To lower the...





. x a M) m c 4 . 1 8 (  1 . 2 3) m c 6 . 3 0 2 (  2 . 0 8) m c 3 . 9 3 3 (  6 . 3 3 1) m c 2 . 7 0 4 (  3 . 0 6 1) m c 0 . 3 4 5 (  8 . 3 1 2) m c 7 . 8 7 6 (  2 . 7 6 2
. n i M)m c 0 . 0 7 (  6 . 7 2)m c 1 . 5 7 1 (  9 . 8 6)m c 8 . 1 9 2 (  9 . 4 1 1)m c 2 . 0 5 3 (  9 . 7 3 1)m c 9 . 6 6 4 (  8 . 3 8 1)m c 7 . 3 8 5 (  8 . 9 2 2
) H x W ( . x a M 6 2 . 9 1 x  8 6 . 5 2
) m c 8 . 8 4 x m c 1 . 5 6 ( 2 1 . 8 4 x  6 1 . 4 6
) m c 2 . 2 2 1 x m c 9 . 2 6 1 ( 6 1 . 0 8 x  8 8 . 6 0 1
) m c 6 . 3...





User Controls
Remote Control Control Panel
Control Panel & Remote Control
There are two ways for you to control the functions: Remote
Control and Control Panel.
Using the Control Panel
On/Standby
Refer to the “Powering On/Off the Projector” section on pages
10-11.
Source
Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
Menu
Press “Menu” to launch the on screen menu (OSM).  To exit
OSM, press “Menu” again.
Keystone   
Adjusts image...





Using the Remote Control
Power
Refer to the “Powering On/Off the Projector” section on pages
10-11.
Source
Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
AUTO ADJ. (Auto Adjust)
When “AUTO ADJ.” is pressed, the projector will automatically
synchronize with source signal.
PiP
Displays the “PiP” menu of the on screen display.
Keystone +  / -
Adjust image distortion caused by tilting the projector (±16
degrees).
Hide
Press “Hide” to hide...





The Projector has multilingual On Screen menus that are
multilingual allowing you to make image adjustments and
change a variety of settings. The projector will automatically
detect the source.
How to operate
1.To open the OSM menu, press “Menu” on the Remote Control or
Control Panel.
2.When OSM is displayed, use     keys to select the main menu.
While making a selection on a particular page, press “Enter / 
”
key to enter sub menu.
3.Use      keys to select the desired item and adjust the...





Language
Language
You can display the multilingual OSM menu . Use the   or 
key to select your prefered language.
Press “Menu” to finalize the selection.

	
	
	

User Controls   





User Controls
All Images
Brightness
Adjusting the brightness of the image.
Press the  to darken image.
Press the  to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
Press the  to decrease the contrast.
Press the  to increase the contrast.
White Peaking
White peaking can be incrementally adjusted between 0 and
10.  Click on the slider...