NEC Multisync Lcd4620 Users Manual

English-19
EnglishConnect the LCD Monitor to a Stereo Amplifier
•Turn on the LCD monitor and the amplifier only after all connections have been made.
•Use a stereo Mini-RCA cable to connect the AUDIO OUT connector (Stereo Mini Jack) on the LCD monitor and the audio
input on the amplifier.
•Do not reverse the audio left and right jacks.
•The AUDIO IN is used for audio input.
•The AUDIO OUT jack outputs sound from the selected Audio input.
Connecting to a Stereo Amplifier*
You can connect your stereo...

English-20
Connecting to a TV*
Precautions when connecting the antenna
•Use a coaxial cable which is free from
interference. Avoid using a parallel flat wire as
interference may occur, causing the reception
to become unstable and noise to appear on the
screen.
•Avoid using an indoor antenna as this may be
affected by interference and poor reception.
•Cable distribution system should be grounded
(earthed) in accordance with ANSI/NFPA 70,
the National Electrical Code (NEC), in
particular Section 820.93,...

English-21
English
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will turn green while powered on and will turn red while powered off.
NOTE:The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the
Power Button on the front of the LCD.
Power Button
POWER
RGB1 RGB2 RGB3 HDMI
DVD/HD
PICTURE
MODE
DISPLAY
AUTO
SET UP
VOL
STILL
PIP
REMOTE IDON/OFF
SET RESET
REMOTE CONTROLLER RU-M111MTS SLEEP INPUT
CHANGE ON/OFF
CAPTUREMUTECH
CH...

English-22
Picture Mode
DVI,VGA, RGB/HV STANDARD sRGB HIGHBRIGHT
HDMI, DVD/HD, STANDARD CINEMA HIGHBRIGHT
VIDEO, TV
Power Indicator
Mode Status Indicator LightPower ON Green*2
Power OFF (Eco Standby)*1RedPower consumption under 1W
Power OFF (Standby) Amber
Power consumption  under 5WPower Save Amber Blinking
Power Standby when Green and Amber
“SCHEDULE SETTINGS” enabled blink alternately
Diagnosis (Detecting failure) Red Blinking
(See Troubleshooting page 35)
*1 When in Eco Standby Mode RS-232C controls...

English-23
English
OSD (On-Screen-Display) Controls
Press UP or DOWN
button to select
sub-menu.Press SET. Press UP or DOWN,
PLUS or MINUS to select
the function or setting to
be adjusted.Press MENU or EXIT.
Remote Control
Press UP or DOWN
button to select.Press INPUT button
to decide.Press UP or DOWN, PLUS
or MINUS button to select.Press EXIT
Control Panel
OSD screen
ADAPTIVE CONTRAST
Goto Adjustment
SelectReturn Close
Input source
Main Menu Icons
Main Menu Item
Sub Menu
Key GuideAdjustment Settings
 

English-24
OSD Setting
PICTURE BRIGHTNESS Adjusts the overall image and background brightness. Press + or - to adjust.
CONTRAST Adjusts the image brightness in relationship to the background. Press + or - to adjust.
Note: The sRGB picture mode is standard and cannot be changed.
SHARPNESS Adjusts the crispness of the image. Press + or - to adjust.
BLACK LEVEL Adjusts the image brightness in relationship to the background. Press + or - to adjust.
TINT* Adjusts the tint of the screen. Press + or - to...

English-25
English
H RESOLUTION Adjusts the horizontal size of the image.INPUT DVI, VGA, RGB/HV only
V RESOLUTION Adjusts the vertical size of the image.INPUT DVI, VGA, RGB/HV only
ZOOM MODE Select the aspect ratio of the screen image.
BASE ZOOM
16:9* For input sources that have a 16:9 aspect ratio.
14:9* For input sources that have a 14:9 aspect ratio.
DYNAMIC* Expands 4:3 picture to fill the screen. Some of the image is lost due to expansion.
OFF Selecting “OFF” will display the image in a 1 by 1 pixel...

English-26
TIME
DAYLIGHT SAVING
SCHEDULE RESET Resets the following settings within the SCHEDULE menu back to factory setting:
OFF TIMER, SCHEDULE SETTINGS.
PIP KEEP PIP MODE* Allows the monitor to remain in “PIP” mode after powering off. When Power is returned, PIP
appears without having to enter the OSD.
PIP MODE* Picture-in-Picture
OFF OFF
PIP PIP
POP POP
SIDE BY SIDE (ASPECT)SIDE BY SIDE ASPECT
SIDE BY SIDE (FULL) SIDE BY SIDE FULL
PIP SIZE Selects the size of the sub-picture used in...

English-27
English
OSD RESET Resets the following settings within the OSD menu back to factory setting:OSD TURN OFF, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY.
MULTI DISPLAY MONITOR ID Sets the monitor ID number from 1-26.
IR CONTROL Selects the mode of the monitor for use with the infra-red remote control when using the
RS-232C daisy chain.
NORMAL The monitor will be controlled normally by wireless remote controller.
PRIMARY Choose “PRIMARY” for the first monitor within an RS-232C daisy chain....

English-28
ADVANCED INPUT DETECT Selects the method of input detection the monitor uses when more than two input devices
OPTIONexcept TV inputare connected.
NONE The Monitor will not search the other video input ports.
FIRST DETECT When the current video input signal is not present, then the monitor searches for a video
INPUT DVI, VGA, RGB/HV onlysignal from the other video input port. If the video signal is present in the other port, then the
monitor switches the video source input port to the new found...