NEC Multisync Lcd5710 Users Manual

							English-19
English
Power Indicator
Using Power Management
The LCD monitor follows the VESA approved DPM Power
Management function.
The power management function is an energy saving
function that automatically reduces the power consumption
of the display when the keyboard or the mouse has not been
used for a fixed period.
The power management feature on your new display has
been set to the “ON” mode. This allows your display to enter
a Power Saving Mode when no signal is applied. This could
potentially increase the life and decrease the power
consumption of the display.
Selecting a video source
To view a video source:
Use the input button to set [VIDEO].
Use the COLOR SYSTEM menu to set [AUTO], [NTSC],
[PAL], [SECAM], [PAL60], [4.43NTSC], according to your
video format.
Picture Size
RGB 1, 2, 3 FULL ZOOM NORMAL
DVD/HD, VIDEOFULL WIDE ZOOM NORMAL
Status
Power ON Green
Power OFF Red
Power Standby when Red On
“SCHEDULE” is enable Green Blinking
Power Standby Red,  Green
Diagnosis (Detecting failure) Red Blinking
* See troubleshooting on page 33
RGB1, 2, 3
DVD/HD
VIDEO
PIP or POP
Main:RGB2
Sub:VIDEO
Information OSM
Video Input mode
Input signal Information
Audio input mode
Picture Size modeRGB2 
1024 x 768 
48kHz  60Hz
AUDIO : 1 
SIZE : FULL
)
Video Input mode
Audio input mode
Picture Size modeDVD/HD
AUDIO : 3 
SIZE : WIDE
Video Input mode
Input Signal Colour System mode
Audio input mode
Picture Size modeVIDEO
NTSC
AUDIO : 3
SIZE : NORMAL
Main picture Information
Sub picture Information
Main picture Information
RGB2 
1024 x 768 
48kHz  60Hz
AUDIO : 1 
VIDEO 
NTSC 
SIZE : FULL
)
Picture Mode
RGB 1, 2, 3 HIGHBRIGHT STANDARDsRGB
DVD/HD, VIDEOHIGHBRIGHT STANDARDCINEMA
Signal Type
NORMAL
ZOOM
(DYNAMIC)
FULL
WIDE 4:3
Squeeze
Letter boxNORMAL SIZE Recommended Size
NORMAL: Display by the inputed signal aspect ratio by PC
signal, or display in 4:3 aspect ratio at DVD/HD or VIDEO signal.
FULL: Display in entire screen.
WIDE: Expand 16:9 letter box signal to entire screen.
ZOOM (DYNAMIC): Expand 4:3 pictures to the entire screen
with non-linearity. (Some around image will be cut by expansion.)
ZOOM
Image can be expanded beyond the active display area. The
image which is outside of active diaplay area is not displayed.
ZOOM
ZOOM
 
						

							English-20
MAIN MENUPICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT:RETURNMENU:EXIT MENU
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT:RETURNMENU:EXIT MENU+ -:ADJ:RETURNMENU:EXIT MENU
32
BRIGHTNESS
EXITEXITEXIT
OSM (On-Screen-Manager) Controls
Press MENU button to
open Main menu.
Press UP or DOWN button
to select sub-menu.Press SET button to
decide.Press UP or DOWN, and PLUS or
MINUS button to select function, or
control which you like.
Press SET button to decide.Press MENU or EXIT
button to exit.
Remote Control
Press UP or DOWN
button to select.Press INPUT button
to decide.Press UP or DOWN, and PLUS or
MINUS button to select function, or
control which you like.
Press INPUT button to decide.Press EXIT button
to exit.
Control Panel
UP or DOWN button INPUT button
OSM screen
Main-Menu
PICTURE
Sub-Menu
Adjusts the overall image and background screen
brightness.
Press + button to increase brightness.
Press - button to decrease brightness.
Adjusts the image brightness in relation to the input
signal.
Press + button to increase contrast.
Press - button to decrease contrast.
NOTE: sRGB picture mode is standard and cannot be
changed.
This function is digitally capable to keep crisp image at
any timing. It is adjustable to get a distinct image or a
soft one as you prefer and set independently for each
picture mode.
Press + button to increase sharpness.
Press - button to decrease sharpness.
Adjusts the image brightness in relation to the
background.
Press + button to increase black level.
Press - button to decrease black level.
NOTE: sRGB picture mode is standard and cannot be
changed.
Adjusts the noise reduction level.
Press + button to increase reduction level.
Press - button to decrease reduction level.
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
NOISE REDUCTION
*:INPUT VIDEO only
MAIN MENUPICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
COLOR 
BLACK LEVEL
NOISE REDUCTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
32
NOISE REDUCTION
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
32
BLACK LEVEL
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
32
SHARPNESS
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
CONTRAST
+ -:ADJ :RETURNMENU:EXIT MENU
32
EXIT
+ -:ADJEXIT:RETURNMENU:EXIT MENU
32
BRIGHTNESSPICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
PLUS and
MINUS buttonEXIT button
 
						

							English-21
English
Adjust the tint of the screen.
Press + button to Skin colour becomes greenish.
Press - button to Skin colour becomes purplish.
Adjust the colour depth of the screen.
Press + button to increase colour depth.
Press - button to decrease colour depth.
R, Y, G, C, B, M, S: Increases or decreases Red, Yellow,
Green, Cyan, Blue, Magenta and Saturation depending
upon which is selected. The change in colour will appear
on screen and the direction (increase or decrease) will be
shown by the colour bars.
NOTE: sRGB picture mode is standard and cannot be
changed.
To adjust the colour temperature of entire screen.
Adjusting lower colour temperature makes the screen
reddish and higher colour temperature makes the screen
bluish.
NOTE: sRGB picture mode is standard and cannot be
changed.
Selecting Picture reset allows you to reset all OSM
settings about PICTURE setting.
Select “Yes” and press “SET” button to restore to factory
preset data.
Press “EXIT” button to cancel and then return to the
previous menu.
TINT
*:INPUT DVD/HD, VIDEO only
COLOR
*:INPUT DVD/HD, VIDEO only
COLOR CONTROL
*:INPUT RGB1,2,3 only
COLOR
TEMPERATURE
PICTURE RESET
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
PICTURE RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
9600K
COLOR TEMPERATURE
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
COLOR CONTROLR
Y
G
C
B
M
S0
0
0
0
0
0
0
EXIT:SEL
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
COLOR 
BLACK LEVEL
NOISE REDUCTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
32
COLOR
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
COLOR 
BLACK LEVEL
NOISE REDUCTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
32
TINT
EXIT
Main-Menu
SCREEN
Sub-Menu
Controls Horizontal Image position within the display
area of the LCD.
Press + button to move screen to right.
Press - button to move screen to left.
Controls Vertical Image position within the display
area of the LCD.
Press + button to move screen to UP.
Press - button to move screen to DOWN.
Press + button to expand the width of the image on
the screen to the right.
Press - button to narrow the width of the image on the
screen to the left.
To change the snow noise of the image.
Adjusts the horizontal size by increasing or decreasing
the setting.
Press + button to expand the width of the image on
the screen.
Press - button to narrow the width of the image on
the screen.
H POSITION
V POSITION
CLOCK
*:INPUT RGB2/3 only
CLOCK PHASE
*:INPUT RGB2/3 only
H RESOLUTION
*:INPUT RGB1/2/3 only
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
1360
H RESOLUTION
EXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
18
CLOCK PHASE
EXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
1782
CLOCK
EXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
0
V POSITION
EXIT
+ -:ADJ :RETURNMENU:EXIT MENU
0
H POSITION
EXIT
SCREENH POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
 
						

							English-22
Adjusts the vertical size by increasing or decreasing the
setting.
Press + button to expand the height of the image on the
screen.
Press - button to narrow the height of the image on
the screen.
Selects the screen zoom mode. Zoom mode will be
selected when you select the “ZOOM” by pushing the
“SIZE” button on remote controller.
When you select the “CUSTOM”, you will be able to
adjust optional horizontal and vertical size.
You can also select 16:9, 14:9 and DYNAMIC.
(INPUT DVD/HD,VIDEO only)
Press “SET” button to show a control menu as follows:
Increase or decrease “ZOOM” slider to adjust the whole
size and then adjust horizontal and vertical size by
HZOOM and V ZOOM. Increase or decrease “H POS”
and “V POS” to adjust the picture position.
Selecting “DYNAMIC” will expand 4:3 pictures to the
entire screen with non-linearity. (Some around image
will be cut by expansion.) Dynamic image is the same
as FULL size image when HDTV 1080i signal is input.
Selecting “OFF image will be displayed 1 by 1 pixel.
(If you input over 1366x768 resolution signal, it will be
displayed as shrank image.)
Selecting Screen reset allows you to reset all
OSM settings from SCREEN setting (except
H POSITION, V POSITION, CLOCK, CLOCK PHASE,
H RESOLUTION, V RESOLUTION).
Select “Yes” and press “SET” button to restore the
factory preset data.
Press “EXIT” button to cancel and then return to the
previous menu.
V RESOLUTION
*:INPUT RGB1/2/3 only
ZOOM MODE
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
SCREEN RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
CUSTOM
:SEL + - :ADJ :RETURNMENU:EXIT MENU
X 1.00
X 1.00
X 1.00
0%
0%ZOOM
H ZOOM
V ZOOM
H POS
V POS
EXIT
ZOOM MODE
CUSTOMV
16:9
14:9
DYNAMIC
OFF
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
768
V RESOLUTION
EXIT
SCREEN RESET
ZOOM MODE
CUSTOM
OFF
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
*:INPUT DVD/HD, VIDEO only*:INPUT RGB1/2/3 only
Main-Menu
AUDIO
Sub-Menu
Adjust the balance of L/R volume.
Press + button to move the stereo sound image to right.
Sound of the left side will be small.
Press - button to move the stereo sound image to left.
To accentuate or reduce the high frequency sound.
Press + button to increase TREBLE sound.
Press - button to decrease TREBLE sound.
To accentuate or reduce the low frequency sound.
Press + button to increase BASS sound.
Press - button to decrease BASS sound.
Selecting Audio reset allows you to reset all OSM
settings from AUDIO setting.
Select “Yes” and press “SET” button to restore the
factory preset.
Press “EXIT” button to cancel and then return to the
previous menu.
BALANCE
TREBLE
BASS
AUDIO RESET
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
AUDIO
BALANCE
TREBLE
BASS
AUDIO RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
AUDIO RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
AUDIO
BALANCE
TREBLE
BASS
AUDIO RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
0
BASS
EXIT
AUDIO
BALANCE
TREBLE
BASS
AUDIO RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
0
TREBLE
EXIT
+ -:ADJ :RETURNMENU:EXIT MENU
R  CENTER
BALANCE
L
EXIT
AUDIO
BALANCE
TREBLE
BASS
AUDIO RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
 
						

							English-23
English
Main-Menu
PICTURE IN PICTURE
Sub-Menu
Selecting the size of picture inserted at the
“Picture-in-Picture” (PIP) mode.
“Large”, “Middle” and “Small” are available.
Selecting the sound source in PIP mode.
When selecting “MAIN AUDIO”, you will get the sound
for the main picture and when selecting “PIP AUDIO”,
you will get the sound for the picture instead.
When side-by-side mode, MAIN AUDIO is the sound
source of the left side screen and PIP AUDIO is the
right side.
Selecting PIP Reset allows you to reset all OSM
settings from PIP setting.
Select “Yes” and press “SET” button to restore the factory
preset data.
Press “EXIT” button to cancel and then return to the
previous menu.
PIP SIZE
PIP AUDIO
PIP RESET
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
PIP
PIP SIZE
PIP AUDIO
PIP RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
PIP RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
PIP
PIP SIZE
PIP AUDIO
PIP RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
PIP AUDIO
MAIN AUDIO           /             PIP AUDIO
EXIT+ -:SEL
:RETURNMENU:EXIT MENU
PIP SIZELARGE
MIDDLE
SMALL
:SELEXIT
PIP
PIP SIZE
PIP AUDIO
PIP RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
Main-Menu
CONFIGURATION 1
Sub-Menu
Press “SET” button to automatically adjust screen size,
horizontal position, vertical position, clock, clock phase,
white level and black level.
Press “EXIT” button to cancel execution AUTO SETUP
and then will return to the previous menu.
Selecting the auto adjust ON/OFF.
Selecting ON when changing the timing, the horizontal
position, vertical position and clock-phase will adjust
automatically.
Selecting the auto brightness ON/OFF.
When select “ON”, the brightness will be automatically
adjusted.
Selecting RGB “ON”, the monitor will go to power
management mode when RGB1,2,3 sync is lost.
Selecting VIDEO “ON”, the monitor will go to power
management mode after about 10 minutes delay from
when DVD/HD and VIDEO input signal is lost.
NOTE: When connecting RGB1, video card might not
stop sending digital data even if image has disappeared.
In this case the monitor does not go to power
management mode.
OSM control menus are available in seven languages.
AUTO SETUP
*:INPUT RGB2/3 only
AUTO ADJUST
*:INPUT RGB2/3 only
AUTO BRIGHTNESS
*:INPUT RGB1/2/3 only
POWER SAVE
LANGUAGE
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXITEXIT
LANGUAGE
ENGLISH
DEUTSCH
FRANCAIS
ESPAÑOL
ITALIANO
SVENSKA
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
POWER SAVERGB         ON           /             OFFVIDEO       ON           /             OFF
:SELEXIT
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
AUTO BRIGHTNESS
ON           /             OFF
EXIT+ -:SEL
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
AUTO ADJUST
ON           /             OFF
EXIT+ -:SEL
:CANCELMENU:EXIT MENU
AUTO SETUP
SETPRESS
TO   RESET
:RESETSETEXIT
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
 
						

							English-24
Select “SCREEN SAVER” functions to reduce the risk of
the “image persistence”.
GAMMA: The display gamma is changed and fixed when
selected “ON”.
COOLING FAN: The built in cooling fan is always on
when set “ON”.
BRIGHTNESS: The brightness is decreased when
selected “ON”.
MOTION: Image is slightly expanded and moves
4directions (UP, DOWN, RIGHT, LEFT) periodically
(Need setting the time for movement).
Movement area is approximately +/- 10mm from original
position; Please locate the important information such as
text within 90% area of screen image.
See note (1) for this functions.
PIP, POP, Side by Side and STILL will be disabled when
“MOTION” is active.
Selecting the Colour System depends on your input
video format.
AUTO: NTSC, PAL, SECAM, PAL60 or 4.43 NTSC is
automatically selected.
NTSC: Specific selection of NTSC.
PAL: Specific selection of PAL.
SECAM: Specific selection of SECAM.
PAL-60: Specific selection of PAL60.
4.43NTSC: Specific selection of 4.43 NTSC.
Adjustment the side black bar color white when 4:3
image displayed, black to white.
Press + button, the bar will become whiter.
Press - button, the bar will become darker.
Selecting the CONFIGURATION RESET allows you to
reset all configuration settings.
Select “Yes” and press “SET” button to restore the factory
preset data.
Press “EXIT” button to cancel and return the previous
menu.
Selecting “YES” allows you to reset PICTURE, SCREEN,
AUDIO, CONFIGURATION1,2 and ADVANCED OPTION
will be back to factory settings (except H POSITION,
V POSITION, CLOCK, CLOCK PHASE,
H RESOLUTION, V RESOLUTION, LANGUAGE,
DATE & TIME and SCHEDULE).
Select “YES” and press “SET” button to restore the
factory preset data.
Press “EXIT” button to cancel and return the previous
menu.
SCREEN SAVER
COLOR SYSTEM
*:INPUT VIDEO only
SIDE BORDER
COLOR
CONFIGURATION
RESET
FACTORY RESET
CONFIGURATION 1
POWER SAVE
LANGUAGE
SCREEN SAVER
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
FACTORY RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
CONFIGURATION 1
POWER SAVE
LANGUAGE
SCREEN SAVER
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
CONFIGURATION RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ
:RETURNMENU:EXIT MENU
SCREEN SAVER
:SEL
  GAMMA
  COOLING FAN
  BRIGHTNESS
  MOTIONON    /    OFF
ON    /    AUTO
ON    /    OFF
      10  SEC.
EXIT
CONFIGURATION 1
POWER SAVE
LANGUAGE
SCREEN SAVER
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
COLOR SYSTEM
AUTODEUTSCH
NTSC
PA L
SECAM
4.43 NTSC
PAL-60
:SEL :RETURNMENU:EXIT MENUEXIT
CONFIGURATION 1
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
POWER SAVE
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
50
SIDE BORDER COLOR
EXIT
Main-Menu
CONFIGURATION 2
Sub-Menu
A set up ON/OFF of long cable alteration can be
performed. In ON, enforcement of an AUTO Set Up
performed alteration.
Please refer to the CD-ROM included for alteration.
LONG CABLE
ON/OFF
*:INPUT RGB2/3 only
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
+ -:SEL :RETURNMENU:EXIT MENU
LONG CABLE ON/OFF
ON           /             OFF
EXIT
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN  OFF
INFORMATION OSM
OFF TIMER
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
 
						

							English-25
English
To compensate for image degradation, which is caused by
using a long cable.
RED/GREEN/BLUE DELAY
To adjust the each phase of RED, GREEN and BLUE
signal.
LEVEL: 0 - 6
RED/GREEN/BLUE SHARPNESS
To adjust the each performance degradation of RED,
GREEN and BLUE signal.
LEVEL: 0 - 45
SOG PEAK
To adjust the shape of Sync on Green signal.
Level: 0 - 1
VIDEO EQ (Input RGB 3 only)
To optimize the shape (Tailing) of RED, GREEN and
BLUE signal.
Level: 0 - 7
SYNC TERMINATE (Input RGB 3 only)
To select the terminate resistance for matching the cable
impedance.
HI: 2.2K ohm/LO:75 ohm
The OSM control menu will stay on as long as it is use.
In the OSM Turn Off submenu, you can select how long
the monitor waits after the last touch of a button to shut
off the OSM control menu. The preset choices are
10 -240 seconds.
Selects the information OSM display or not. The
information OSM will display when input signal or
source change or warning message like as no-signal or
out-of range.
A time between 3 to 10 seconds is available.
To select OFF TIMER mode ON/OFF.
In the OFF TIMER menu, you can preset the monitor to
automatically power down.
A time between 1 to 24 hours is available.
When the OFF TIMER is set, the SCHEDULE
(see page 28) settings will be disabled.
Selects the kind of DVI-D equipment which is connected
RGB1.
Select “DVI-PC” when PC or other computer equipment
is connected.
Select “DVI-HD” when DVD player, which has DVI-D
output, is connected.
Adjusts the position of the OSM menu.
Press + button to move right side of the screen.
Press - button to move left side of the screen.
Press 
 button to move right side of the screen.
Press 
 button to move left side of the screen.
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN  OFF
INFORMATION OSM
OFF TIMER
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
LONG CABLE MANUAL
RED DELY
GREEN DELAY
BLUE DELAY
RED SHARPNESS
GREEN SHARPNESS
BLUE SHARPNESS
SOG PEAK
VIDEO EQ.
SYNC TERMINATE
:SEL :RETURNMENU:EXIT MENU
+ -:ADJ
     0
     2
     0
     0
     0
     0
     0
     0
HI  /  LO
EXIT
LONG CABLE
MANUAL
*:INPUT RGB2/3 only
OSM TURN OFF
INFORMATION OSM
OFF TIMER
DVI MODE
*:INPUT RGB1 only
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN  OFF
INFORMATION OSM
OFF TIMER
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
OFF TIMERON            1   HOUR
OFF
+ -:ADJ:SELEXIT
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN  OFF
INFORMATION OSM
OFF TIMER
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
INFORMATION OSMON                 10 SEC.
OFF
+ -:ADJ:SELEXIT
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN  OFF
INFORMATION OSM
OFF TIMER
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
OSM TURN  OFF
10 SEC.
EXIT
CONFIGURATION 2
OSM TURN  OFF
INFORMATION OSM
OFF TIMER
DVI MODE
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
DVI MODE
DVI-PC        /       DVI-HD
+ -:SELEXIT
OSM POSITION
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN  OFF
INFORMATION OSM
OFF TIMER
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
OSM POSITION
+ - :ADJ
RIGHT LEFT
UP
DOWN
EXIT
 
						

							English-26
Selects the method of input detection when more than
two computers are connected.
FIRST DETECT:  When the current video input signal is
not present, then the monitor searches for a video signal
from the other video input port. If the video signal is
present in the other port, then the monitor switches the
video source input port to the new found video source
automatically. The monitor will not look for other video
signals while the current video source is present.
This function is available at input RGB 1/2/3.
LAST DETECT:  When the monitor is displaying a signal
from the current source and a new secondary source is
supplied to the monitor, the monitor will automatically
switch to the new video source. When current video input
signal is not present, the monitor searches for a video
signal from the other video input port. If the video signal
is present in the other port, then the monitor switches the
video source input port to the new found video source
automatically.
This function is available at input RGB 1/2/3.
VIDEO DETECT: DVD/HD or VIDEO inputs will have
priority over RGB1/2/3. When DVD/HD or VIDEO input
signal is present the monitor will change and keep to the
DVD/DH or VIDEO input.
NONE: The Monitor will not search the other video input
port.
Indicates the model and serial number of your monitor.
INPUT DETECT
MONITOR
INFORMATION
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN  OFF
INFORMATION OSM
OFF TIMER
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
INPUT DETECTFIRST
LAST   
VIDEO
NONEDETECT
DETECT
DETECT
:SELEXIT
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN  OFF
INFORMATION OSM
OFF TIMER
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
MONITOR INFORMATIONMODEL  NAME:
     LCD5710
SERIAL:
   12315XXX
EXIT
Main-Menu
ADVANCED OPTION
Sub-Menu
Selects the S-Video input port function.
PRIORITY:
If cable is connected to the S-Video input, it will have
priority the composite input port.
SEPARATE:
S-Video port and Composite port are selectable as
independent input port.
Selects to decision of input signal about below timings,
1024x768, 1280x768 and 1360x768.
AUTO: Determines the resolution automatically.
1024x768: Determines the resolution as 1024x768
1280x768: Determines the resolution as 1280x768
1360x768: Determines the resolution as 1360x768
Selects a level of black expansion.
In case of go under the black cut-off level, please adjust
the “Black level” in moderation on OSM menu.
Selects a display gamma.
    2.2
    2.4
    S gamma
    Native
NOTE: sRGB picture mode is standard and cannot be
changed.
S-VIDEO MODE
INPUT RESOLUTION
*:INPUT RGB2/3 only
BLACK LEVEL
EXPANSION
*:INPUT VIDEO only
GAMMA SELECTION
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
ADVANCED OPTION
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
BLACK LEVEL EXPANSION
HIGH    /   MIDDLE  /   OFF
+ -:SELEXIT
ADVANCED OPTION
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:EXIT MENU:RETURNMENU
GAMMA SELECTION2.  2
2.  4
S  GAMMA
NATIVE
:SELEXIT:EXIT MENU
ADVANCED OPTION
S-VIDEO MODE 
INPUT RESOLUTION
GAMMA SELECTION
IMAGE FLIP
MONITOR ID
TILE MATRIX
HEAT PROTECT
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
:RETURNMENU:EXIT MENU
S-VIDEO MODE
PRIORITY           /           SEPARATE
+ -:SELEXIT
ADVANCED OPTION
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
:RETURNMENU:EXIT MENU
INPUT RESOLUTION
:SEL
AUTO
1024 X 768
1280 X 768
1360 X 768
EXIT
 
						

							English-27
English
Selects the image flipping or rotation.
NORMAL: Normal display.
H MIRROR: Mirror image for horizontal direction.
V MIRROR: Mirror image for vertical direction.
ROTATE: Rotate the image 180 degrees.
Changes the display area of the image.
OVERSCAN: Set to display area about 95%
UNDERSCAN: Set to display area about 100%
Selects IP (Interlace to Progressive) converter function.
PROGRESSIVE: Enable the IP function, to convert
interlace signal to progressive. Normally use this setting.
INTERLACE: Disable the IP function.
NOTE: This mode is better suited for motional pictures,
but it is in danger of image retention.
Selects Film mode function.
AUTO: Enable the Film mode function. This mode is
better suited for movies, which is converted 24 Frames/
sec source to DVD Video. We recommend to select
“PROGRESSIVE” in “SCAN CONVERSION”.
OFF: Disable the Film mode function. This mode is
better suited for Broadcasting or VCR source.
Set the Monitor ID number to control the daisy chained
multiple MultiSync LCD5710 with RS-232C.
The Monitor ID number is selectable between 1 and 26.
Selects the infrared wireless remote controller mode
with using the RS-232C daisy chain.
The item in this menu will become effective by pressing
“SET” button on the selected item.
NORMAL: The monitor will be controlled normally by
wireless remote controller.
PRIMARY: Set “PRIMARY” at the head of the daisy
chained monitors by RS-232C.
SECONDARY: Set “SECONDARY” after 2nd daisy
chained monitor.
LOCK: Disable the monitor control by infrared wireless
remote controller.
Keep pressing “DISPLAY” button during 5 sec or more,
this setting will return to “NORMAL”.
Tile Matrix demonstrates multiple screens. This feature
provides a single large screen using up to 25 monitors.
It will be able to divide up to 5 each H and V.
This requires you to feed the PC output into each of the
monitors through a distributor.
H MONITORS: Select number of horizontal divide.
V MONITORS: Select number of vertical divide.
POSITION: Select a position to expand the screen.
TILE COMP: Works in tandem with Tile Matrix to
compensate for the width of the tile bezels in order to
accurately display the image.
ENABLE: Select “YES”, the monitor will expand the
selected position.
PIP, POP, SIDE by SIDE and STILL and “DYNAMIC”
ZOOM mode will be disabled when “TILE MATRIX” is
activated.
IMAGE FLIP
SCAN MODE
*:INPUT DVD/HD, VIDEO only
SCAN CONVERSION
FILM MODE
*:INPUT DVD/HD, VIDEO only
MONITOR  ID
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXT :RETURNMENU:EXIT MENU
ADVANCED OPTION
EXIT:RETURNMENU:EXIT MENU
MONITOR ID
ID No.                 1
+ -: SELEXIT
ADVANCED OPTION
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXT :RETURNMENU:EXIT MENUEXITMENU:EXIT MENU:RETURN
FILM MODE
AUTO      /     OFF 
+ -: SELEXIT
ADVANCED OPTION
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
ADVANCED OPTION
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
:RETURNMENU:EXIT MENU
SCAN MODE
OVERSCAN      /   UNDERSCAN
+ -: SELEXIT
IR CONTROL
TILE MATRIX
:RETURNMENU:EXIT MENU
IMAGE FLIP
:SEL
NORMAL
H MIRROR
V MIRROR
ROTAT E
EXIT
ADVANCED OPTION
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
SCAN CONVERSION
PROGRESSIVE        /     INTERLACE
+ -: SELEXIT
ADVANCED OPTION
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
IR CONTROLNORMAL
PRIMARY
SECONDARY
LOCK
:SELSET:SETEXIT
ADVANCED OPTION
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXITMENU:EXIT MENU
TILE MATRIX
:SEL 
H  MONITORS
V  MONITORS
POSITION
TILE COMP
ENABLE1
1
1
YES   /      NO
YES   /      NO
EXIT:RETURN
+ -: ADJ
 
						

							English-28
Information of status for COOLING FAN, BRIGHTNESS
and TEMPERATURE.
COOLING FAN comes to run when inside temperature
is over a guaranteed limit.
BRIGHTNESS comes to be decreased when inside
temperature is over guaranteed limit with cooling fun.
In this case warning is displayed on the screen.
Adjusts the delay time from “standby” to “power on”
mode.
“POWER ON DELAY” time is selectable between 0 and
50 sec.
Adjusts the current date and time for internal clock.
You should set this function when you use “SCHEDULE”.
Programs the monitor’s working
schedule.
Schedule the power on and
power off with hour and a day of
the week. Also sets the input port.
This OSM can’t remove except
EXIT.
(see “NOTE 3” on page 29 for
further information)
Selecting ADVANCED OPTION reset allows you to reset
all OSM settings from ADVANCED OPTION settings,
except for DATE & TIME, and SCHEDULE.
Select “YES” and press “SET” button to restore the
factory preset data.
Press “EXIT” button to cancel and then return the
previous menu.
ADVANCED OPTION
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURN :SETMENU:EXIT MENU
DATE & TIMEYEAR
MONTH
DAY
TIME
DAYLIGHT SAVING     YES   /    NO
CURRENT DATE             TIME
    JAN. 01. 2004     00  :  00  :  002004
JANUARY
01
00  :  00
SET+ -: ADJEXIT
NOTE 1: IMAGE PERSISTENCE
Please be aware that LCD Technology may experience a phenomena known as Image Persistence. Image Persistence occurs when a
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a long period of time should be avoided.
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver
at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE” functions to further reduce the risk of Image persistence.
For long life use of Public Display
< Image Sticking of LCD Panel >
When LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or
ghost image of previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along
the displayed image, and it is observed permanently. (Image Sticking)
< Recommendations >
For preventing the fast transition to Image Sticking, and for longer life usage of LCD, following are recommended.
1. Fixed image should not be displayed for long period, and changed to another images with short cycle.
2. When no use, please turn off the monitor by remote control, or use Power Management Function of monitor or use Schedule Function of
monitor.
HEAT STATUS
DATE & TIME
SCHEDULE
ADVANCED OPTION
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
ADVANCED OPTION RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
ADVANCED OPTION
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
POWER ON DELAY
 3 SEC.
+ -: ADJEXIT
ADVANCED
OPTION RESET
ADVANCED OPTION
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
EXIT
ADVANCED OPTION
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXITEXIT:RETURNMENU:EXIT MENU
HEAT STATUSSTATUS
COOLING   FAN1                ON 
COOLING   FAN2                ON
BRIGHTNESS                      NORMAL
TEMPERATURE
     SENSOR 1       0.0    C   /  32.0  F
     SENSOR 1       0.0    C   /  32.0  F
POWER ON DELAY