NEC Multisync P701 Users Manual

User’s Manual
MultiSync P701
 

Index
Declaration of conformity ........................................................................\
..................................................... English-1
Important Information ........................................................................\
.................................. ......................... English-2
WARNING, CAUTION ........................................................................\
....................................... ......... English-2
Declaration...

English-1
EnglishFor USA
FCC Information
1. Use the attached specified cables with the MultiSync P701 (L709NG) col\
or display so as not to interfere with radio andtelevision reception.
(1) Please use the supplied power cord or equivalent to ensure FCC complianc\
e.
(2) Please use a good quality shielded video signal cable.
Use of other cables and adapters may cause interference with radio and t\
elevision reception.
2. This equipment has been tested and found to comply with the limits for a\
 class A...

English-2
Important Information
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROMWALL SOCKET. TO FULLY DISENGAGE...

English-3
EnglishFOR OPTIMUM PERFORMANCE, PLEASE NOTE THEFOLLOWING WHEN SETTING UP AND USING THE MULTI-FUNCTION MONITOR:
• DO NOT OPEN THE MONITOR . There are no user
serviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other risks.
Refer all servicing to qualified service personnel.
• Do not spill any liquids into the cabinet or use your monitor near water.
• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage...

English-4
Contents
Your new MultiSync monitor box* should contain the following:
• LCD monitor
• Power cord*
1
• Video Signal Cable
• Wireless Remote Control and AA Batteries
• Cable cover
• Setup Manual
• Clamp• Screw (M4) x 7
• CD-ROM
• Eyebolt (M12) x 2
• Washer for eyebolt (M12) x 2
• Eyebolt (M8) x 2
• Washer for eyebolt (M8) x 2
* Remember to save your original box and packing material to transport or \
ship the monitor.
*
1Type and number of power cords included will depend on the where the LCD \...

English-5
EnglishThis device cannot be used or installed without the TabletopStand or other mounting accessory for support. For properinstallation it is strongly recommended to use a trained,NEC authorized service person. Failure to follow NECstandard mounting procedures could result in damage to theequipment or injury to the user or installer. Product warrantydoes not cover damage caused by improper installation.Failure to follow these recommendations could result invoiding the warranty.
In order to...

English-6
Attaching Mounting Accessories
The display is designed for use with the VESA mounting
system.
1. Attach Mounting Accessories
CAUTION:Attaching mounting accessories must be done
by using eyebolts (M12).
Do not attempt to mount or carry the display
using your own strength as the display may fall
and cause personal injury.
When attaching the mounting accessories, do
not cover the fan.
Be careful to avoid tipping monitor when attaching
accessories.
Mounting accessories can be attached with the...

English-7
English
Cord or chain
b. Prevent Tipping
When using the display with the optional tabletop stand,
fasten the LCD to a wall using a cord or chain that can
support the weight of the monitor in order to prevent the
monitor from falling. Fasten the cord or chain to the monitor
using the eyebolts (M8).
When using eyebolts (M8) for prevent the monitor from
falling, attach the eyebolts (M8) to backside position, as
shown below.
NOTE:Before attaching the LCD monitor to the wall,
make sure that the...

English-8
 EXIT button
Activates the OSD menu when the OSD menu is turned-off.
Acts as EXIT button within the OSD to move to previous
menu.
  Remote control sensor and Power Indicator
Receives the signal from the remote control (when using the
wireless remote control). See also page 12.
Glows green when the LCD monitor is in active mode*.
Glows red when the LCD is in POWER OFF (ECO standby)
mode. Glows amber when the LCD is in POWER OFF
(standby) mode. Blinks amber when the monitor is in Power
Save...