Nikon Camera Coolpix P530 Reference Manual

							E45
Reference Section
2Select  On, and then press the  k 
button.
3Press the  d button to display the shooting screen.
4Press the shutter-release button to 
shoot the first image.
5Press the shutter-release button to 
shoot the second image.
•Frame the picture while looking at the first 
image displayed translucently.
• When shooting the second image, the 
combined image of the first and second 
images is saved, and displayed translucently.
• To end multiple exposure at the second 
image, set Multiple exposure mode  to Off  or change the mo de dial to any 
mode other than  j, k , l , m  or  M.
6Press the shutter-release button to shoot the third image.
• The combined image of the first to third images is saved and multiple 
exposure ends.
• It may take some time until the third image is shot.
Off On
Multiple exposure mode
1/250 1/250
1/250
F5.6
F5.6
F5.625m 0s
25m 0s
25m 0s840840
1/250 1/250
1/250F5.6
F5.6
F5.625m 0s
25m 0s
25m 0s840840 
						

							E46
Reference Section
Zoom Memory
BNotes About Zoom Operation
•When more than one focal length has been set, move the zoom control  to switch 
to the focal length closest to that before  the operation. To switch to a different 
focal length, release the zoom co ntrol and then move it again.
• Set  Zoom memory  to Off  when using the digital zoom.
Rotate the mode dial to  j, k, l, m  or  M M  d  button  M j, k, l , m  or 
M  tab ( A9) M Zoom memory
OptionDescription
On When the zoom control is moved, the zoom position 
(equivalent to focal length/angle of view in 35mm [135] 
format) is switched to the positions that have been 
selected by setting the check box to on in this menu 
option. The following se
ttings are available: 24 mm , 28 
mm,  35 mm , 50 mm , 85 mm , 105 mm , 135 mm , 200 
mm,  300 mm , 400 mm , 500 mm , 600 mm , 800 mm 
and  1000 mm .
• Choose the focal length with the multi selector, and 
then press the  k button to set the check box to on 
[ w ] or off.
• The default setting is on [ w] for all the check boxes.
• To finish setting, press the multi selector  K.
• The zoom position set in the  Startup zoom position 
is automatically set to on [ w].
Off (default setting) The zoom position can be
 moved to any position, 
including the positions that can be set with  On. 
						

							E47
Reference Section
Startup Zoom Position
Set the zoom position (equivalent to fo cal length/angle of view in 35mm [135] 
format) for when the camera is turned on.
The following settings are available:  24 mm (default setting),  28 mm, 35 mm , 
50 mm , 85 mm , 105 mm  and 135 mm .
M Exposure Preview
Set whether or not to reflect the brightness to the shooting screen when the 
exposure is changed in  m (manual) mode.
Rotate the mode dial to 
j
, k, l, m  or  M M  d  button  M j, k, l , m  or 
M  tab ( A9) M Startup zoom position
Rotate the mode dial to  j
, k, l, m  or  M M  d  button  M j, k, l , m  or 
M  tab ( A9) M M exposure preview
OptionDescription
On Reflects the brightness to the shooting screen.
Off 
(default setting) Does not reflect the brightness to the shooting screen. 
						

							E48
Reference Section
See “Editing Still Images“ ( E7) for information about image editing functions.
aPrint Order (Creating a DPOF Print Order)
If you configure print orde r settings in advance, you can use them with the 
printing methods listed below.
• Taking the memory card to a digital pho to lab that supports DPOF (Digital 
Print Order Format) printing.
• Inserting the memory card into a DPOF-compatible printer’s card slot.
• Connecting the camera to a Pict Bridge-compatible printer (E15).
1Use the multi selector  HI to 
select  Select images , and press 
the  k button.
2Select images (up to 99) and the 
number of copies (up to 9) of each.
•Use the multi selector  JK or rotate it to 
select images, and use  HI to specify the 
number of copies to be printed.
• Images selected for pr inting are indicated 
by the check mark icon and the numeral 
indicating the number of copies to be 
printed. If no copies have been specified for images, the selection is 
canceled.
• Move the zoom control toward  g (i ) to switch to full-frame playback or  f 
( h ) to switch to thumbnail playback.
• Press the k  button when setting is complete.
The Playback Menu
Press the c button (playback mode)  M d  button ( A8) M a  Print 
order
Delete print order Select images
Print order
1 1
1
1
1 32
23
Back
Print selection 
						

							E49
Reference Section
3Select whether or not to print 
shooting date and shooting 
information.
•Select  Date and press the  k button to 
print the shooting date on all images.
• Select  Info and press the k  button to print 
the shutter speed and aperture value on all 
images.
• Lastly, select  Done and press the k  button to complete the print order.
BNotes About Printing Shooting Date and Shooting Information
•Some printers may not be able to print the shooting date and shooting 
information.
• Shooting information is not printed when the camera is connected to a printer.
• The  Date  and Info settings are reset each time the  Print order option is 
displayed.
• The date printed is that saved when the image was 
captured. 
• For images taken with the  Print date (E 64) 
option enabled, only the date imprinted at the 
time of shooting are printed, even if the  Print 
order  date option is enabled for the images.
CCanceling Existing Print Order
Select  Delete print order  in step 1 of print order ( E48).
CMore Information
See “Printing Images of Size 1:1” ( E23) for more information.
Info Date
Done
Print order
15/05/20141 5 / 0 5 / 2 0 1 415/05/2014 
						

							E50
Reference Section
bSlide Show
Play back images one by one in an au tomated “slide show.” When movie files 
( A 89) are played back in the slide show,  only the first frame of each movie is 
displayed.
1Use the multi selector  HI to 
select  Start and press the  k 
button.
• The slide show begins.
• To change the interval between images, 
select  Frame intvl , press the k button, 
and specify the desired interval time before 
selecting  Start.
• To repeat the slide show automatically, select  Loop and press the  k button 
before selecting  Start.
• The maximum playback time is up to about 30 minutes even if  Loop is 
enabled.
2Select End or Restart.
• The screen shown on the right is displayed 
after the slide show ends or is paused. To 
exit the show, select  G and then press the 
k  button. To resume the slide show, select 
F  and then press the  k button.
Operations During Playback
• Use  JK  to display the previous/next image. Press and hold to rewind/fast 
forward.
• Press the  k button to pause or end the slide show.
Press the 
c button (playback mode)  M d  button ( A8) M b Slide
show
3sLoop
Frame intvl Start Pause
Slide show 
						

							E51
Reference Section
d Protect
The camera protects selected images from accidental deletion.
Select images to protect or cancel protection for previously protected images 
from the image selection screen ( A84).
Note that formatting the camera’s internal memory or the memory card 
( E 69) permanently dele tes protected files.
fRotate Image
Specify the orientation in which saved  images are displayed during playback. 
Still images can be rotated 90 de grees clockwise or 90 degrees 
counterclockwise.
Images that were saved in the “tall” orie ntation can be rotated up to 180 degrees 
in either direction.
Select an image from the image selection screen ( A84). When the Rotate 
image screen is displayed, use the multi selector  JK or rotate it to rotate the 
image 90 degrees.
Press the  k button to finalize display or ientation, and save orientation 
information with the image. Press the 
c button (playback mode)  M d  button ( A8) M d Protect
Press the  c button (playback mode)  M d  button (A 8) M f Rotate
image
Rotate
Back
Rotate image
Rotate
Back
Rotate image
Rotate
Back
Rotate image
Rotate 90 degrees 
counterclockwise Rotate 90 degrees
clockwise 
						

							E52
Reference Section
E Voice Memo
Voice memos can be recorded and attached to images.
Recording Voice Memos
• Press and hold the k  button to record (up to 
about 20 seconds).
• Do not touch the microphone.
• During recording, o  and p flash in the 
monitor.
• The voice memo playback screen is displayed 
after recording ends. Press the  k button to 
play back the voice memo.
• Delete the current voice memo before recording a new voice memo.
• p is displayed for images with a voic e memo when in full-frame playback 
mode.
• Press the multi selector  J before or after recording a voice memo to return 
to the playback menu.
Playing Voice Memos
Select an image with  p displayed before 
pressing the  d button.
• Press the  k button to play the voice memo. 
Press the button again to stop playback.
• Move the zoom control during playback to 
adjust playback volume.
• Press  J before or after pl aying a voice memo 
to return to the playback menu.
Deleting Voice Memos
Press the  l button on the voice memo playback 
screen. Use  HI to select  Ye s and press the  k 
button.
• To delete a voice memo for a protected 
image, the 
Protect setting must first be 
disabled.
Press the 
c button (playback mode)  M select an image  M d  button
( A 8) M E  Voice memo
20s20s
Back Back
12s12s
No
Yes
   File will be deleted. OK? 
						

							E53
Reference Section
hCopy (Copy Between In ternal Memory and 
Memory Card)
Copy images or movies between the  internal memory and a memory card.
1Use the multi selector HI to 
select a destination option to 
which images are copied and press 
the 
k button.
2Select a copy option and press the 
k button.
• If you choose the  Selected images  option, 
use the image selection screen to specify 
images ( A84).
BNotes About Copying Images
•Only files in formats that this  camera can save can be copied.
• Operation is not guaranteed with images ca ptured with another make of camera or 
that have been modified on a computer.
• The  Print order  (E 48) settings configured for images are not copied.
CNotes About Copying Images in a Sequence
•If you select a key picture of a sequence in  Selected images, all images in the 
sequence are copied.
• If you press the  d button while images in a sequence are displayed, only the 
Card to camera  copy option is available. All imag es in the sequence are copied if 
you select  Current sequence .
CCopying to a Memory Card That Contains No Images
When the camera is swit ched to playback mode,  Memory contains no images.  is 
displayed. Press the  d button to select  Copy.
Press the  c button (playback mode)  M d  button ( A8) M h Copy
Card to camera Camera to card
Copy
All images Selected images
Camera to card 
						

							E54
Reference Section
CSequence Display Options
Select the method used to display images in the sequence ( E5).
Settings are applied to all sequences, and the setting is saved in the camera’s 
memory even if the camera is turned off.
x Choose Key Picture
Specify a different image in the sequence as the key picture.
•When the key picture selection screen is displayed, select an image ( A84).
Press the 
c button (playback mode)  M d  button ( A8) M C  
Sequence display options
OptionDescription
Individual pictures Displays each image in 
a sequence individually. 
F is 
displayed on the playback screen.
Key picture only 
(default setting) Displays only the key picture for images in a sequence.
Press the c
 button (playback mode)  M display a sequence for which you 
want to change the key picture  M d  button ( A8) M x  Choose key 
picture