Norstar Compact 616 Dr5 Installer Guide

14  Programming
 Telephone TelephoneM7324 Telephone
You should have two aids to assist you in completing your
programming:
Programming Record
The Compact  Programming Record may already have
been completed before installation. It describes the settings to be
programmed into 
a  system. Also, the Programming
Record serves as a record of the settings programmed at initial
installation and during subsequent upgrades.
Default settings: Many of the programming settings are
determined during System Startup...

Programming  15
The Programming Overlay for the M7208 Telephone is placed
over all of the eight memory buttons (Figure 11). The
Programming Overlay for the M7310 and M7324 Telephones
(Figure 11) is placed over the top four memory buttons with
indicators.
Figure 11 Programming Overlay for the M7208 Telephone (top) and for
the M7310 and M7324 Telephone (bottom) 

16  Frogramming
   
System Startup overview
 
Perform System Startup after the system hardware has been
installed and powered up. System Startup is used by the installer
to choose the appropriate template before starting programming.
There are three templates available: Square, Hybrid and PBX.
The Compact 
 Programming Record explains what each
template does.
CAUTION
Startup is to be used for initial installation only, or after a
system software upgrade with a new Software
Cartridge. Do not use Startup...

Programming  17
Entering System Startup 
If at any time you do not wish to continue with entering
1,
2.
3.
System Startup, press  
 
Select a  telephone from which to program. Place the
correct Programming Overlay over the buttons of the
telephone. A button may be used during programming when
its indicator  turns 
Using the telephone dial pad, press the System Startup
Access code: 
Which is the same as:
At the Password: prompt, enter the Installer password:
Which is the same as:
(The Installer password...

18  Programming     
Choosing the system template
1.The display shows Reset memory? To continue with System
Startup and choose the system template, press 
 (or
 on the M7208 Telephone).
OR
To exit from System Startup, press  (or  on the
M7310 and M7324 Telephone).
The display shows  ate: Square. To accept the
Square template, go to step 3.
OR
To select another template, press  (or  on
the M7208 Telephone} to select another template.
3.To accept the template shown and exit from System Startup,
press NEXT...

Programming  19
Configuration Overview  
Configuration programming allows you to specify basic system
characteristics for the customer site. Configuratian is not
accessible to System 
 
Configuration provides access to the following programming
sections:
  Data
2. Line Access
3, 
 Handling
4. Miscellaneous
5. System Data
Configuration Access Code
1.Press 
OR
Press
Installer Password
1.At the Password: prompt, enter in the existing Installer
password. The default password is  which you will
have to use if...

20  Programming   --
Chart 5 Configuration Overview
START HERE
Enter digits for Configuration code
Heading
3.Call Hand1 
Next
Back
   

 Data
Programming  21
Use 1.  Data to program characteristics for each
external line.
When you are finished programming the  Data settings
for a line, you may copy those exact settings to another line by
using the  display button (or  on the M7208
Telephone) at the 
Show 1  prompt.
Entering the line to be programmed
Enter any available line number between 01 and 06.
Dial Mode
A dial mode can be assigned to each line. The mode defines the
signaling that the line will use. The default mode is Pulse....

22  Programming
Line Type
A type can be assigned to each line. The type defines how the
line is to be used in relation to other lines in the system. The
default type is Public. Other possible types are Private, Pool A,
Pool B and Pool C.
If you define a line as Public, the line can be accessed by
more than one telephone.
If you define a line as Private, the line can only be assigned
to one telephone.
If you assign a line to a Line Pool, that line can be available
to any telephone that is assigned access...

Programming  23
Auxiliary ringer
An auxiliary ringer can be enabled or disabled for calls coming in
on the line. The default setting is Yes, which means that the
ringer will ring. Another possible setting is No.
 Auto privacy
Auto privacy can be enabled so that other users who have
access to a line on their telephone, cannot use that line while a
call is already in progress on the line.’ If disabled, Auto privacy
allows a user to select a line in use at another telephone, and
join an  call.
Chart 6...