Nortel M7310 Telephone User Card Manual

							aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaa
M7310
Telephone
User Card 
						

							2
Your Norstar M7310 telephone
Contrast level 2
DOWN UP OKUsing display
buttonsDisplay buttons change with each feature you use.
The labels for display buttons appear in capital
letters directly above them on the second line of
the display.  A display button with an ÒOKÓ label
above it is represented as 
OK in this card.
Confirm that your memory and line buttons have the correct snap-on caps by
checking their programming.
1. Release all calls or open lines with dial tone.
2. Press Ä¥â.
3. Press  the button(s) you want to check and read the display.
4. Press ÄÊ when finished.
1. Press Ä¥à.
2. Press 
UP or DOWN for the level you want.
3. Press 
OK when finished.
1. Press Ä¥ß.
2. Press Ú,Û, Ü or Ý to hear the different types of rings.
3. While the telephone is ringing, press à to adjust the volume.
4. Press 
OK to store the ring.
Shift buttonfor using the top function of a dual-memory button.
Displayshows the time, date, call information and guides you while using Norstar* features.
The lower line of the display is reserved for display button instructions.
Dual-memory buttons
store any two features and/or autodial numbers.
Display buttons
Feature button
starts or cancels a feature.
Release buttoncancels active calls.
Hold button
Dial pad
Memory and line buttons
are buttons with indicators for
one touch dialing, feature
operation or line access.
Volume control
Indicators
appear beside active lines and features.
Button inquiry
Adjusting display
contrast
Selecting a ring type
and volume level
softer louder
* Meridian and Norstar are trademarks of Northern Telecom.
Important: All M7310 telephones Release 16 (REL 16) and higher comply with the Americans with Disabilities Act
(ADA).  See the label on the bottom of the telephone for the Release marking. 
						

							3
Making calls
About line buttonsNorstar systems can have different types of line buttons.  Match the line
buttons on your telephone with the ones below for instructions on how to use
them.
Internal calls using Intercom buttons
1. Pick up the receiver.
2. If ¼ appears beside an Intercom
button, then dial.
OR
Press an Intercom button without
¼ , then dial.
External calls using numbered Line
buttons
1. Pick up the receiver.
2. When ¼ appears beside a
numbered Line button, then dial.
OR
Press a numbered Line button
without ¼ , then dial.
Note:Internal numbers are supplied by your System Coordinator.
Internal calls using extension
buttons
1. Pick up the receiver.
2. When ¼ appears beside an
extension button, then dial.
Holding Calls
1. Press ú.Ê Ê The ¼ flashes beside the line on hold.
2. Press the line button with the flashing ¼ to return to the call.
Check the display for confirmation or additional information.
Automatic hold
Calls are put on hold automatically when you switch from one line to another.
This button operates the telephones built-in microphone and speaker in place
of the receiver.  Your System Coordinator can program Handsfree to your
telephone.
Making calls
1. Press © instead of picking up the receiver.
Switching between Handsfree and handset
1. Press © and replace the handset to switch to Handsfree.
2. Pick up the receiver to switch back.
Using Mute
1. Press © to turn the microphone OFF.
2. Press ©Ê again to turn the microphone ON.
1. Press a line  button without ¼ , then dial your call.
2. When answered, pick up the receiver, or press ©.
3. If the call is not answered, or the  line is busy,  press ¨.
Dialing without
lifting the handset
ºLine 1
Æ
º
4321
ú
©
External calls using extension
buttons
1. Pick up the receiver.
2. When ¼ appears beside the
extension button, then dial á
(or your systems external line
access code) and the number. 
						

							4P0749850  Issue 02 Printed in Canada
About memory
buttons
Programming memory buttons
Features
1. If you are on a call or an open line
with dial tone, press ú
or ¨.
2. Press Ä¥Ü.
3. Press a memory button.
4. Press Ä and the feature
code.
5. Label your new button.
Programming
memory buttonsExternal autodial
1. If you are on a call or an open line
with dial tone, press ú
or ¨.
2. Press Ä¥Ú.
3. Press a memory button.
4. Dial the external number.
5. Press
OK to store the number.
6. Label your new button.
Erasing memory buttons
1. If you are on a call or an open line
with dial tone, press ú
or ¨.
2. Press Ä¥Ú.
3. Press the memory button you
want to erase.
4. Press
OK to erase the button.
Remember:Press Ä¥â to check a memory or line button.
Internal autodial
1. If you are on a call or an open line
with dial tone, press ú
or ¨.
2. Press Ä¥Û.
3. Press a memory button.
4. Dial the internal number.
5. Label your new button.There are two types of memory
buttons: single-memory and dual-
memory.  Memory buttons store
telephone numbers or feature
codes to give you one touch
dialing or feature activation.
Dual-memory buttons
To use the bottom function, press
the dual-memory button.
To use the top function, press the
shift button, then press the dual-
memory button.
Single-memory buttons
Single-memory buttons are the
buttons with indicators other than
line or Handsfree buttons.
Music ON
Shift
Mom
Home George
Dentist
Line Pool
Call Timer
BottomTop