Olympus Vp 1 Projector User Manual

E-21
Connecting Personal Computers and Video Equipment
Connections with Video Connectors
Video Equipment with VIDEO Connectors
* Make the connection to the VIDEO connector of the projector using a video cable.
Video Equipment with S-VIDEO Connectors
* Make the connection to the VIDEO connector of the projector using an S-video cable.
PC
VIDEO AUDIO
S-VIDEO
VIDEO
S-Video cable (Suppled item)Video deck, DVD player,
document camera, etc.
Video cable (Supplied item)
Note
Please see Page E-28 “Input...

E-22
PC
VIDEO AUDIO
CrCbY
Pr Pb YCOMPONENT
COMPONENT
Connecting Personal Computers and Video Equipment
Connections with Component Video Sources
When the Video Connectors are Y, Cb, and Cr Connectors* Make the connection to the projector’s VIDEO connector using a component cable (which is available
as an option).
DVD player, HD video
deck, etc.
Note
* Please see Page E-28 “Input Selection” for information about making input selections.
* YCbCr cannot accept the input of signals other than NTSC 3.58 and...

E-23
Connecting Personal Computers and Video Equipment
Connections with Audio Connectors
* Make the connection to the projector’s AUDIO jack using an audio cable.
* The built-in speaker of the projector provides monaural audio.
* To enjoy convincing audio reproduction, please connect the audio output of the video equipment to
your audio system.
PC
VIDEO AUDIO
R LAUDIO
Audio cable (Supplied item)Video equipment, personal computer
Note
The AUDIO jack of the projector is a 2.5 mm diameter stereo mini jack....

E-24
Power Cable Connections and Switching the Power On/Off
There is an order in which the power cable is connected and the power is switched on/off.
Operating
1Connect the AC IN connector of the projector and the power outlet using the sup-
plied power cable.
The POWER indicator will light amber, the cooling fan will rotate at low speed, and the unit will enter
the standby mode.
POWER
AU
TO M
EN
U
STATUSP
O
W
ERSOURCEQ
U
ICK
M
EN
U
PC
AUDIOVIDEO
STATUS
POWER
Lit amber
To wall outlet
Firmly plug in all...

E-25
Power Cable Connections and Switching the Power On/Off
Finishing
1Switch off the power of the connected equipment
2Switch off the power of the projector
Main unit operation: Press and hold the POWER button for 1 second.
Remote control operation: Press the POWER OFF button.
ON OFFPOWER
The “Power Off” indication will appear.
When the red bar extends fully (in about 5 sec-
onds), the projection screen will go off and the
unit will enter the power off operation.
Note
* The operation can be cancelled by...

E-26
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal
being input to the projector.
Projection Screen Position Adjustment
Adjust the projection image to the screen.Check that the screen is set level and vertically.
(1) If the image is shifted to the left or right, move the main unit horizontally. (Align the center of the
screen and the center of the lens of the main unit.)
(2) If the image is shifted vertically, move the...

E-27 Using the Adjusters
Adjustment of the Projection Screen
(
1)
POWER
AUTO MENU
STATUSPOWERSOURCEQUICK
MENU
(
1)
(
2)
POWER
AUTO MENU
STATUSPOWERSOURCEQUICK
MENU
PC
AUDIOVIDEO
Raising the projection image
While viewing the projection im-
age, press and hold the front ad-
juster buttons located at the left
and right (1) and, raise the projec-
tor to align the image with the
screen, then release your fingers
(2).
Turn the left and right front adjust-
ers for fine adjustment.
Adjust so that there is no...

E-28
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see “Menu Operation Method” on Page E-37 and
the various items on Pages E-46 to E-60.
Input Selection
This operation selects the input signal to be projected.
Main unit operation: Press the SOURCE button.
(It will not function while the menu or the quick menu is displayed.)
When Auto Source is On
If there is no input signal at the source...

E-29
Automatic Adjustment of Analog RGB
General Operation
MENU
AUTO
SOURCE
QUICK
MENU
ON OFF
FREEZE MUTE PIP
DIGITAL RGB YPbPr
VIDEO S-VIDEO YCbCr
QUICK ASPECT AUTOPOWER
This function automatically adjusts the position shift of the analog
RGB input signal, the size of the picture, vertical striping, and
color infidelity.
Normally, this function is adjusted automatically at the time of sig-
nal selection.
Main unit operation/Remote control operation: Press the
AUTO button. (This will not function while...

E-30
DIGITAL RGB YPbPr
VIDEO S-VIDEO YCbCr
QUICK
CANCELMENU
ASPECT AUTO
Image of the Personal Computer
(when selecting digital RGB or analog RGB)
Each press of the ASPECT button advances the selection one
step in the sequence of Auto → Direct → Real, and then repeats.
Auto ............ Automatically enlarges or reduces the image to project a
full screen in a ratio of 4:3
Direct .......... Maintains the aspect ratio and projects a picture of the maxi-
mum displayable size
Real ............ Projects the...