Palm M130 Handheld Instructions Manual

3
CHAPTER 1
Introduction to Your Handheld
This chapter explains the physical buttons and controls on your Palm™ m100 
series handheld, how to use your handheld for the first time, how to add expansion 
cards to your handheld, and how to use HotSync
® technology to synchronize your 
handheld and Palm™ Desktop software.
Getting to know your Palm™ m100 series handheld
What is a Palm m100 series handheld?
Palm m100 series handhelds will help you stay organized and on time, and keep 
up with daily tasks while...

Chapter 1 Introduction to Your Handheld
4
System requirements
To install and operate Palm Desktop software, your computer system must meet 
the following requirements:
Minimum requirements: Windows 
nIBM-compatible Pentium-class computer 
nWindows 95*/98/Me/NT 4.0*/2000**/XP** (* Windows 95/NT operating 
systems require a serial cradle/cable, sold separately. ** User must have 
administrator rights to install Palm Desktop software.)
n30 MB available hard disk space
nVGA monitor or better (16 bit or High...

Getting to know your Palm™ m10 0 series handheld
5
Handheld components
Locating front panel controls
 
Power button/ 
Backlight controlTurns your handheld on or off and controls the backlight feature. If 
your handheld is turned off, pressing the power button turns the 
unit on and returns you to the last screen you viewed.
If your handheld is turned on, pressing the power button turns the 
unit off. Pressing the power button for about two seconds sets the 
brightness of the backlight to high or low....

Chapter 1 Introduction to Your Handheld
6
Using the backlight
When your handheld is on, a backlight illuminates your screen and enables you to 
see the information, even under difficult lighting conditions. The backlight 
brightness is initially set to high, but you can set the brightness to low to save 
power. When you set the brightness, your handheld remembers your preference 
until you change the brightness. 
To set the backlight:
nPress the power button and hold it down for about two seconds....

Upgrading from another Palm OS handheld
7
Upgrading from another Palm OS handheld
If you already own a Palm OS handheld, you must install the version of Palm 
Desktop software that comes with your new handheld. To upgrade quickly and 
easily, perform the tasks described in the following sections. Some tasks are 
specifically for upgrading.
StylusServes as a pointing and writing device for navigating through 
applications and entering data on your handheld. To use the 
stylus, slide it out of the storage...

Chapter 1 Introduction to Your Handheld
8
Preparing to use your handheld
Before you begin using your handheld and Palm Desktop software, you must 
complete a few easy installation tasks. 
To use your handheld and Palm Desktop software, complete the following:
n(If upgrading) Perform a HotSync operation using your old handheld and 
cradle/cable. This ensures all data on your handheld is on your desktop 
computer.
nConnect the HotSync cradle/cable that comes with your Palm m100 series 
handheld to your...

Preparing to use your handheld
9
To remove the cover:
1.Open the cover and grasp the hinge with your thumb.
2.Gently rock the cover from one side to the other until the hinge prongs release 
from the slots on the top edge of your handheld.
To reattach the cover:
nAlign the hinge prongs with the slots on the top edge of your handheld, and 
then insert one prong at a time until the prongs lock inside the slots.
Changing the face plate
You can personalize the appearance of your handheld by changing the face...

Chapter 1 Introduction to Your Handheld
10
To remove the face plate:
1.Remove the flip cover.
2.Lift the face plate tab slightly to separate it from your handheld and pull the 
existing face plate away from your handheld.
To attach the face plate:
1.Align the bottom edge of the new face plate with the slot on the bottom edge of 
your handheld.
2.Gently press the top of the face plate onto your handheld until it clicks into 
position.
Connecting the HotSync cradle/cable
IMPORTANTThe HotSync cradle/cable...

Preparing to use your handheld
11
3.Connect the power cord that attaches to the back of the cradle’s USB port 
connector to the AC adapter cord.
4.Plug the adapter into any AC current outlet.
Charging the handheld
Your handheld is recharged  each time you place the handheld in the cradle. Just 
place your handheld in the cradle for at least two hours for an initial charge before 
you use it. Then place it in the cradle for ten to fifteen minutes each day to recharge 
the battery to full capacity. 
If the...

Chapter 1 Introduction to Your Handheld
12
Palm Desktop software
Palm Desktop software extends many of the functions of your handheld to your 
computer and serves to back up all your data. Viewing and editing your data using 
Palm Desktop software is optional. However, when you use it with your handheld 
and the built-in HotSync technology, you can fully synchronize the information on 
your handheld with the information on your computer. 
It is a good idea to back up your data in case something happens...