Panasonic A47 Dome Camera Quick Start Guide

							Network Mini Dome Camera·Quick Operation Guide  20 Figure 2-12 Fix the Adapter Plate 3. Install the dome drive to the adapter plate.  Figure 2-13 Fix the Dome Drive  
						

							Network Mini Dome Camera·Quick Operation Guide  214. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.  Figure 2-14 Install the Front Cover 5. Tear off the protection film softly to complete the installation.   Do not tear off the protection film until the installation is completed.  Do not touch the inside face of the bubble with your hands. 2.4 Wall Bracket Mounting Steps:  
						

							Network Mini Dome Camera·Quick Operation Guide  221. Install the wall bracket to the wall with the supplied screws in the wall bracket package.  The matched ceiling bracket model is DS-1272ZJ-120B, and you need to purchases it separately if wall bracket mounting is adopted.  Figure 2-15 Install Wall Bracket 2. Fix the adapter plate to the wall bracket.  Figure 2-16 Fix the Adapter Plate  
						

							Network Mini Dome Camera·Quick Operation Guide  233. Fix the dome drive to the wall bracket with the supplied screws.  Figure 2-17 Install the Camera 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.  Figure 2-18 Install the Front Cover 5. Tear off the protection film softly to complete the installation.   Do not tear off the protection film until the installation is completed.  
						

							Network Mini Dome Camera·Quick Operation Guide  24 Do not touch the inside face of the bubble with your hands. 2.5 Install the Micro SD Card This series of camera supports local storage, please refer to the following steps to install the micro SD card. Steps: 1. Remove the front cover by loosening the set screws on it.  Figure 2-19 Remove the Front Cover 2. Insert the micro SD card to the card slot until you hear a click. 3. (Optional)Slightly push the inserted micro SD card to uninstall it from the camera.  
						

							Network Mini Dome Camera·Quick Operation Guide  25 Figure 2-20 Install and Uninstall Micro SD Card Mirco SD Card 
						

							Network Mini Dome Camera·Quick Operation Guide  263 Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or PCNVR software to search and change the IP of network camera.  The following figure shows the cable connection of network camera and PC:  Figure 3-1 Wiring over LAN  Set the IP address of the camera for accessing via LAN. Steps: To set the IP address, please use the Advidia Camera Finder Utility as described below:  To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the Advidia Camera Finder Utility.  
						

							Network Mini Dome Camera·Quick Operation Guide  27Refer to the following introductions to set IP address with the Advidia Camera Finder Utility software (for more detailed instructions please download the Camera Finder manual from the Advidia Website www.advidia.com/support):  After launching the Advidia Camera Finder software, it automatically searches the online devices from the subnet where your computer is located.  This search may take 30 seconds or more depending on network size. After searching it will show total number and information of the Advidia cameras found on the network. Device information including the device type, IP address, port number, gateway, etc. will be displayed.  Figure 3-2 Advidia Camera Finder Note: To perform a manual search for additional cameras:  
						

							Network Mini Dome Camera·Quick Operation Guide  28Click the refresh icon  to refresh the online device list manually. The newly discovered devices will be added to the list. Note: You can click on each column heading to order the information.  Modify device information Steps: 1). Select the device(s) to be modified in the device list as shown in Figure 3-3.  2). Click on “File” and select “Login Manager ” as shown in Figure 3-4 to enter the username and password information of selected device(s). 3). Enter the username and password information of the admin account of each device you wish to modify in the “Username” and “Password” fields and click the Save icon  to save the changes. 4). Close the Login Manager and select “Launch Edit Table” under the “Edit” menu dropdown or with Ctrl+E as seen in figure 3-5.  Figure 3-3 Select a Device  
						

							Network Mini Dome Camera·Quick Operation Guide  29     Figure 3-4 Login Manager   Figure 3-5 Launch Edit Table