Panasonic Aj D95dc Operating Instructions Manual

21
Display position
The position of the superimposed display characters
can be changed by setting setup menu items No.004
“CHARA H-POS” and No.005 “CHARA V-POS.” 
(See page 29)
Superimposed Screens

When the PAGE button and DATA+ button or DATA–
button are pressed, the counter display appears
temporarily on the TV monitor while these buttons are
held down to enable the setting to be checked.
Even while the PAGE button is pressed, the settings
can be performed using the DATA+ button or DATA–
button while...

22

OWhen the beginning or end of the tape has been
detected in the VTR operation mode, “BOT
(beginning of tape)” or “EOT (end of tape)” is
displayed at the beginning of the line. 
Examples of what is displayed:
EOT STOP
(stop mode at end of tape)
BOT STANDBY OFF
(standby mode at beginning of tape)
OIn the T&S&R mode, one of the following error
displays appears on the third line (line with the
amount of remaining tape).
[FAN STOP]:
This appears when the cooling fan has stopped.  
When this happens,...

23
Setup (Initial Settings)
The unit’s main settings can be performed and
checked using the on-screen menus which are
displayed on the video monitor connected to the unit. 
It is also possible to perform and check the settings
using the item numbers and setting numbers which
appear on the front panel’s display area.
A user setting memory is provided.  The desired
settings can be stored in this memory in advance for
use during operation.
Setting method using on-screen
menus
Set the LOCAL/MENU/REMOTE...

24
Setup (Initial Settings)
SET–UP MENU 
NO
FACTORY (ALL)
FACTORY (NOT SYSTEM)
USER (ALL)
USER (NOT SYSTEM)
Press the MENU-UP button or MENU-DOWN
button to move the cursor to FACTORY (ALL),
and press the SET button.
OIf this operation is performed with the cursor
moved to FACTORY (NOT SYSTEM) instead,
all the factory settings except for the SYSTEM
menu settings will be restored.
OIf this operation is performed with the cursor
moved to NO, the factory settings are not
restored, and operation is returned...

25
How to load the user defaults
Set the LOCAL/MENU/REMOTE switch to the
MENU position.
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.1
Press the RESET button.
The unit is set to the default setting mode, and
the default setting screen appears on the video
monitor.2
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the LOAD
position, and press the SET button.
The unit is set to the LOAD mode, and the load
screen appears on the video...

26
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the NO position,
and press the SET button.
The menu protection is now released.3
Set the LOCAL/MENU/REMOTE switch to the
LOCAL or REMOTE position.
The unit is set to the menu protect mode.
When the LOCAL/MENU/REMOTE switch is set
to the MENU position, the menu setting mode is
not established, and “MENU PROTECTED”
appears on the video monitor screen.

If the LOCAL/MENU/REMOTE switch is set to
the MENU position while holding down the...

27
SYSTEM menu
Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
00 ENCODER SEL
0000
0001
REMOTE
LOCAL
For setting whether the encoder adjustments (for the analog video output
signals) are to be performed by the external encoder remote controller or
the unit.
0: Adjustments are performed by the external encoder remote controller.
1: Adjustments are performed by the unit.
The underlining indicates the factory setting.
01 VIDEO LEVEL 0000
0128
0255–128
0
127For setting the...

28
09 SCH FINE 0000
0255–128127For finely adjusting SCH.
Maximum variation range: ±45 degrees
Together with the SCH COARSE adjustment, 360 degrees are covered.
SYSTEM menu
Item Setting
No.Superimposed
display No.Superimposed
display Description of setting
10 AV PHASE 0000
0255–128127For adjusting the phase of the audio output to the video output.
Variation range: Increments of 20.8 µs
Setup Menus

OThe ( ) setting items are not initialized by the regular menu resetting operation.
20 P.ON LOAD
0000...

29

OIf the PAGE button and DATA+ button or DATA– button are pressed when the CHARA H-POS or
CHARA V-POS item has been set, the counter display appears temporarily while this button is held
down to enable the setting to be checked.
Even while the PAGE button is pressed, the settings can be performed using the DATA+ button or
DATA– button while the actual status is checked.
000 LOCAL ENA
0000
0001
0002DIS
ST&EJENAFor setting the switches which can be operated on the front panel when the
REMOTE/LOCAL...

30
100 SEARCH SPEED
0000
0001X4.1X8.4For setting the speed at which the tape is to be decelerated when the
search switch on the front panel has been pressed.
0: 4.1a
normal tape speed
1: 8.4a
normal tape speed
101 SHTL MAX
0000
0001
0002
X8.4
X16
X32
For setting the maximum speed in the shuttle mode when the external
controller connected to the 9-pin remote connector is used.
0: 8.4a
normal tape speed
1: 16a
normal tape speed
2: 32a
normal tape speed
103 AUDIO MUTE
0000
0001OFFONFor setting the status...