Panasonic Aj Rc10g Operating Instructions Manual

E-10
ENGLISH
Parts and functions (Continued)
Basic camera operations (Continued)
!9GAIN display
This displays the image gain of the camera 
recorder. The initial value is the gain value 
at the time when the GAIN switch on the 
camera recorder was set to “L”.
!10M.GAIN 3 button
When this button is pressed, the image gain 
of the camera recorder is increased.
The lamp is on only when this button is 
pressed.
!11M.GAIN 4 button
When this button is pressed, the image gain 
of the camera recorder is...

E-11
Parts and functions (Continued)
Basic camera operations (Continued)
!14MATRIX ON button
This button switches the matrix function ON/
OFF. Even if the MATRIX is set to “OFF” in 
the menu of the camera recorder, it switches 
to “ON” when this button is pressed. “A” and 
“B” of the MATRIX TABLE and the settings 
for the table can be set with the menu on the 
unit.
The lamp is on when the MATRIX is ON; 
otherwise, the lamp is off.
!15DTL OFF button
This button switches the DETAIL function of 
the camera...

E-12
ENGLISH
Parts and functions (Continued)
Volume settings
!1VR ACTIVE button
This is a button to approve/inhibit operations 
of the GAIN volumes from !2 to !3 and the 
BLACK volumes from !4 to !6.
When the power of the unit is on, it inhibits 
operations.
The lamp is on when the approving/ 
operations are activated; otherwise, the 
lamp is off.
!2R GAIN volume
This adjusts the Rch gain.
The absolute value/relative value mode can 
be switched in the GAIN-VR-MODE item of 
the WHITE menu of the unit....

E-13
Parts and functions (Continued)
Menu operation of the unit
!1LCD panel
This displays the menus for items selected 
with the menu operation buttons !2, !5, !8, 
!11, !14 and !17.
This is also capable of displaying the time 
code.
!2BLACK/SHAD button
This selects the large item displayed on the 
LCD panel. The display will switch to 
BLACK # SHAD # before entering into the 
menu mode # BLACK step by step every 
time the button is pressed.
!3BLACK lamp
This lamp is on when BLACK is selected on 
the LCD...

E-14
ENGLISH
Parts and functions (Continued)
!14KNEE/FUNC button
This selects the large item displayed on the 
LCD panel. The display will switch to KNEE 
# FUNC # before entering the menu mode 
# KNEE step by step every time the button 
is pressed.
!15KNEE lamp
This lamp is on when the KNEE is selected 
on the LCD panel.
!16FUNC lamp
This lamp is on when the FUNC is selected 
on the LCD panel.
!17SHUTTER/SYSTEM button
This selects the large item displayed on the 
LCD panel. The display will switch to...

E-15
Parts and functions (Continued)
Rear panel
!1Camera connection connector
To connect the 10-pin camera control cable.
!2VIDEO OUT connector
An NTSC or PAL monitor is connected for 
operating the menu on the main unit of the 
camera recorder.
!3Cable length selector switch
This switch is on for a 50 m cable.
!4Frequency characteristics 
adjustment volume
This adjusts the frequency characteristics of 
the VIDEO signals.
!5Level adjustment volume
This adjusts the level of the VIDEO signals.
!6Covering...

E-16
ENGLISH
Basic operations
When the power is on
When the POWER button is pressed, the lamp 
for the PANEL ACTIVE button is on, and the 
settings of the camera recorder are read into the 
unit.
The respective numerical values are displayed 
on the PRE/A/B display, CC/ND display, GAIN 
display, and the IRIS display, while R GAIN and B 
GAIN are displayed on the LCD panel.
In this case, only the PANEL ACTIVE button, the 
SW ACTIVE button, the VR ACTIVE button, the 
AUTO IRIS button, M.PED volume and the...

E-17
Basic operations (Continued)
Operation of the camera recorder
1) Operation of the display interlocking 
switch
Select the white balance settings by using the 
PRE/A/B button and monitoring the PRE/A/B 
display.
The state of the camera recorder filter is 
displayed on the CC/ND display.
If two filters are installed on the camera 
recorder, it is impossible to switch the filters 
from the unit but it is possible to switch the 
display by using the FILTER ND/CC button.
The ND filter is indicated with...

E-18
ENGLISH
Basic operation (Continued)
Operation of the camera using the unit volume
When the lamp of the PANEL ACTIVE button is 
on, operations of the M.PED volume and the 
IRIS volume are enabled. When the lamp of the 
AUTO IRIS button is on, the IRIS volume 
functions as the volume for setting the target 
value of the auto iris. When the lamp of the VR 
ACTIVE button is on, operations of the GAIN 
volume and the BLACK volume are enabled.
In the unit menu, it is possible to select whether 
the GAIN...

E-19
Basic operation (Continued)
3) M.PED volume
When the volume operation is enabled, the 
unit operates in the absolute value mode 
where the value is fixed in accordance with 
the position of the volume. The value will be 
“0” by clicking the center.
The variable amount is within a range 
between the minimum value of –200 and the 
maximum value of +200 with the center value 
of 0.Operation of the scene file
The unit has five sets of scene files and is 
capable to storing the current settings as a...