Home
>
Panasonic
>
Communications System
>
Panasonic All-in-One Headset Wx Ch2050 Operating Instructions
Panasonic All-in-One Headset Wx Ch2050 Operating Instructions
Have a look at the manual Panasonic All-in-One Headset Wx Ch2050 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 5
5
qHead Band and Head Pad
Adjustable to your head by sliding the head pad.
wBattery Lock [EJECT]
When removing the battery, slide out the lock.
When loading a new battery, insert the battery until the
lock clicks.
eBattery (Optional accessory)
See PRECAUTIONS.
rHead Pad Cushion
tStrap (Standard accessory)
ySwitch Pocket
Do not open the lid. Should be opened only by qualified
service personnel or system installers.
uEarphone Pad
iMicrophone Boom
Adjust the microphone position to your mouth by rotat-
ing...](http://img.usermanuals.tech/thumb/58/75053/w64_wx-ch2050_en_om_d-4.png "Page 5
5
qHead Band and Head Pad
Adjustable to your head by sliding the head pad.
wBattery Lock [EJECT]
When removing the battery, slide out the lock.
When loading a new battery, insert the battery until the
lock clicks.
eBattery (Optional accessory)
See PRECAUTIONS.
rHead Pad Cushion
tStrap (Standard accessory)
ySwitch Pocket
Do not open the lid. Should be opened only by qualified
service personnel or system installers.
uEarphone Pad
iMicrophone Boom
Adjust the microphone position to your mouth by rotat-
ing...")
![Page 6
6
OPERATING PROCEDURES
Notes:
•Transmission using the talk [T] or page [P] button is
allowed for a single headset at a time. A continuous
beep or distorted sound will be heard in a headset that
tries to transmit while another person is operating.
•Maintain a distance of more than 0.3 m (1 ft) between
the headset and the order taker, or more than 1 m (3 ft)
between the headset and the center module.
●Preparations
Prior to operating the headset, confirm that the system
setup for the headset, center module,...](http://img.usermanuals.tech/thumb/58/75053/w64_wx-ch2050_en_om_d-5.png "Page 6
6
OPERATING PROCEDURES
Notes:
•Transmission using the talk [T] or page [P] button is
allowed for a single headset at a time. A continuous
beep or distorted sound will be heard in a headset that
tries to transmit while another person is operating.
•Maintain a distance of more than 0.3 m (1 ft) between
the headset and the order taker, or more than 1 m (3 ft)
between the headset and the center module.
●Preparations
Prior to operating the headset, confirm that the system
setup for the headset, center module,...")
![Page 7
7
●Communications with Customers
[TALK]
Any store personnel wearing the headset can communicate
bidirectionally with any customer who is at the menu board.
1. Select a proper sound level by pressing the [
▲] or [▼]
button.
2. You will hear a tone in the headset when a vehicle
arrives at the menu board.
Note:The tone duration varies depending on the set-
tings made in the center module.
1. Press the talk [T] button and speak to the customer.
A short beep repeats in the headset.
2. Press the button again...](http://img.usermanuals.tech/thumb/58/75053/w64_wx-ch2050_en_om_d-6.png "Page 7
7
●Communications with Customers
[TALK]
Any store personnel wearing the headset can communicate
bidirectionally with any customer who is at the menu board.
1. Select a proper sound level by pressing the [
▲] or [▼]
button.
2. You will hear a tone in the headset when a vehicle
arrives at the menu board.
Note:The tone duration varies depending on the set-
tings made in the center module.
1. Press the talk [T] button and speak to the customer.
A short beep repeats in the headset.
2. Press the button again...")
![Page 13
13
1. Press the power button to turn off the headset.
2. While holding down the talk [T] and page [P] buttons
simultaneously, press the power button to turn on the
headset.
The headset enters the setup mode where the indica-
tors and buttons have different functions than in normal
operation.
3. Select a default channel setup from four options, press-
ing the [T] button.
4. Press the [A/B] button to move to the talk setup and
page setup.
5. Select a talk mode, pressing the [T] button.
6. Select a page...](http://img.usermanuals.tech/thumb/58/75053/w64_wx-ch2050_en_om_d-12.png "Page 13
13
1. Press the power button to turn off the headset.
2. While holding down the talk [T] and page [P] buttons
simultaneously, press the power button to turn on the
headset.
The headset enters the setup mode where the indica-
tors and buttons have different functions than in normal
operation.
3. Select a default channel setup from four options, press-
ing the [T] button.
4. Press the [A/B] button to move to the talk setup and
page setup.
5. Select a talk mode, pressing the [T] button.
6. Select a page...")
11 ●DIP Switch Setup An eight-bit DIP switch is provided for system setups. The initial setting is marked with an asterisk *. 1. Press the power button to turn off the headset. 2. Set the switches as follows. SW#1: For selection of a radio frequency suitable for the location ON: Applies the US frequency to the headset. OFF: Applies the Canadian frequency. SW#2:Not used SW#3:Not used SW#4:Not used SW#5: Not used SW#6: Enables or disables the tone squelch function. ON: Outputs audio after detecting the tone squelch. OFF: Outputs audio disregarding the tone squelch. Notes: •Set the switch to the normal ON position. Pay attention to a high level noise that may be out- put when set to OFF. •SW#6 and SW#8 are used for channel interfer- ence check while turning on the headset. See below. 1 SW# 2 3 4 5 6 7 8Location Function Tone Squelch Talk Lock ResumptionUSA* ON ON* ON ON*CANADA OFF OFF* OFF* OFF* OFF* OFF OFF* SW#7:While talking with a customer in the TALK lock mode, you may need to contact store personnel in the PAGE mode which interrupts the TALK mode. This switch specifies the status of the interrupted TALK lock mode after ending the PAGE mode. ON:Resumes the TALK lock mode. OFF:Releases the TALK lock mode. SW#8: ON ●Channel Interference Check SW#6 and SW#8 have the specific function of checking whether or not there is radio wave interference in the select- ed channel group. 1. Press the power button to turn off the headset. 2. Set the switches as follows, and turn on the headset. A loud noise will be heard in the headset. SW#6: OFF SW#8: ON 3. Listen to the sound while repeatedly pressing the [A/B] button. Only random noise will be heard if there is no interfer- ence. The presence of any foreign sound indicates that there is interference.
12
● Operation Mode Setup
Three operation modes can be set up to adapt the headset to your requirements.
•Default channel setup
•Talk lock/ Talk PTT (press to talk)
•Page lock/Page PTT
Indicator
Selected ModeSelection
Transition
Exit
Off
PowerA/B channel
RedGreen
Default Channel Setup
Selected
Channel A/B Button
A
BEnable Disable
Talk Setup
Talk Lock
Talk PTT
Page Setup
Page PTT
Page Lock
PTT stands for press to talk.
The default settings are enclosed in bold lines in the table.Blink
On
Blink
Blink
On
OnOn
On
On
Blink
Blink
A
B
EnableDisable
Press
[POWER]. ——— —
—
—
—
—
—
—
While holding down
and buttons,
press [POWER].
TP
—
T
T
P
—
—
A/B
13 1. Press the power button to turn off the headset. 2. While holding down the talk [T] and page [P] buttons simultaneously, press the power button to turn on the headset. The headset enters the setup mode where the indica- tors and buttons have different functions than in normal operation. 3. Select a default channel setup from four options, press- ing the [T] button. 4. Press the [A/B] button to move to the talk setup and page setup. 5. Select a talk mode, pressing the [T] button. 6. Select a page mode, pressing the [P] button. 7. Press the [A/B] button to confirm that the indicators show the three modes selected for the default channel, talk and page. 8. Press the power button to turn off the headset, then turn it on again. The newly selected operation mode will be applied to the headset.
PANASONIC CANADA INC.5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010Panasonic Digital Communications & Security CompanyUnit of Matsushita Electric Corporation of America Information Systems Group Zone Office1707 N.Randall Road, Elgin, IL 60123 (866) 472-6767 Printed in Japan2003 © Matsushita Electric Industrial Co., Ltd. All rights reserved.N0403-2103 3TR001649CAA Imprimé au Japon