Panasonic Cf 07 Mk1 Winxp Owners Manual

Model No.CF-07 Series
Reference Manual
Personal Computer
®
Contents
We recommend that this Reference Manual be printed.
LED Indicators...................................................2
Standby/Hibernation Functions.......................3
Security Measures.............................................7
Computing on the Road .................................11
Battery Power.................................................12
CD-ROM Drive* ...............................................17
PC...

2
This indicator lights when the hard disk drive is accessed.
Not lit: Battery pack is not connected or charging not
being performed.
Orange* : Charging in progress.
Green* : Fully-charged.
Blinking green: Battery is discharging to prescribed charging level
in high temperature mode.
Red: The battery level is very low (the charge is less
than approx. 9% capacity).
Connect the AC adaptor. You can use the com-
puter when the indicator light is orange. If you do
not have an AC adaptor, save your data and...

3
Standby/Hibernation Functions
Starting Up Your Computer Quickly
We recommend plugging in the AC adaptor if the standby function is to be
used for a long period of time. If the AC adaptor cannot be connected, we
recommend that hibernation mode be used instead of the standby mode.
If the standby or hibernation function is used repeatedly, the computer may
not work properly. To stabilize computer operations, we recommend shutting
down Windows on a regular basis (about once a week) without using the...

4
Standby/Hibernation Functions
Precautions
Before entering the standby or hibernation mode
Save all data.
When a file in an external device such as a CD drive, external hard disk, or ATA
card is opened, close the file.
Do not enter either the standby or hibernation mode under the following condi-
tions.  You may corrupt your data or file, the standby or hibernation function may
not work, or the computer (or peripherals) may fail to work properly.
• When the hard disk drive indicator (
) ( page 2) or...

5
After releasing your finger from the power switch, do not touch the power switch
until the power indicator goes off or blinks.
At the “beep” sound, release your finger from the power switch.  If you continue
to press down on the switch and hold it for more than four seconds, the unit will
emit a second “beep” then power off.  Data not previously saved will be lost.
Even when [When I press the power button on my computer] is set to [Shut
down] with [Start] - [Control Panel] - [Performance and...

6
Standby/Hibernation Functions
Resuming Operation
Until resuming is complete (requires about 30 seconds), avoid the following:
• Touching the external keyboard (except for password input), touchscreen, or
power switch.
• Using external mouse or other peripheral devices
• Connecting or disconnecting the AC adaptor.
• Shutting down or restarting Windows.
• Entering the standby or hibernation mode again.
When resuming from the hibernation mode, it may take one or two minutes until
the DISPLAY READY...

7
Security Measures
To prevent unauthorized access of your computer, the various security measures are provided below.
You should set your “Supervisor Password” and “User Password” (The User Password
can only be set when the Supervisor Password has been set).
Without the password, access to your computer is impossible.
 Starting up when the password is set
When [Password on boot] of [Security] menu is set to [Enable], enter your pass-
word*1 and press   Enter   .
When you do not want your computer to be...

8
Security Measures

Setting the Supervisor Password (enabling, changing, disabling)
1Run the Setup Utility ( page 28)
2Using either     or     , select [Security]
3Using either     or    , select [Set Supervisor Password] and
press   Enter
4
Enter your password at [Enter Current Password] and press
Enter
5Enter your password at [Enter New Password] and press
Enter
To disable the Supervisor Password
Press only   Enter
6Re-enter your password at [Confirm New Password] and press
Enter
To disable the...

9
Security Measures

Setting the User Password (enabling, changing, disabling)
1Run the Setup Utility ( page 28)
2Using either     or    , select [Security]
3Using either    or    , select [Set User Password] and press
Enter
4
Enter your password at [Enter Current Password] and press
Enter
5Enter your password at [Enter New Password] and press
Enter

 To disable the User Password
Press only   Enter
6Re-enter your password at [Confirm New Password] and press
Enter

 To disable the User Password
Press only...

10
Security Measures
1
Run the Setup Utility ( page 28)
2Using either    or    , select [Security]
3Using either    or    , select [Hard Disk Lock] and press
  Enter
4To enable the Hard Disk Lock
Select [Enable] and press    Enter
At [Caution], press   Enter   .
To disable the Hard Disk Lock
Select [Disable] and press    Enter
5Press   F10   and select [Yes], then press   Enter
If your computer requires repair
Contact Panasonic Technical Support.
Be sure to set [Hard Disk Lock] to [Disable].
In the...