Panasonic Cf 08 Owners Manual

							31
„When terminating the connection
Perform the following operation.
zTap [Start] - [Log Off] - [Log Off].

You can terminate the connection using the following 
operation.
zTap   (A), and when the message appears, tap  .
CAUTION
zIf you tap [Start] - [Shut Down], the power for the server itself will be turned off.
Make the settings (only for the Supervisor)
„When settings have been changed
Before turning off the wireless display, save (back up) the settings making refer-
ence to step 
9 in “First-time Operation” (Îpage 27).
„When deleting settings
Perform the following procedure.
ADouble-tap   on the desktop and double-tap [Flash Delete].
BConnect your wireless display to a power outlet. 
(Îpage 19)
CTap [Delete Backup].
When the confirmation message appears, tap [Yes].
Deleting data will start.
DWhen the message “Backup data has been deleted.” appears, tap  .
NOTENOTE
zWhen you turn on the wireless display next time, the calibration screen will 
appear. 
(Îpage 20)
„When returning the wireless display to its condition at the time of shipment
Perform the following procedure while the wireless display is turned off.
AConnect your wireless display to a power outlet. 
(Îpage 19)
CF-08.book  31 ページ  ２００６年４月６日　木曜日　午後６時３８分 
						

							32
Starting Up/Shutting Down
BPress the power button with the keyboard button and USER button (Îpage 
38
) pressed until the message “Reset the device to factory default...” appears.
zWhen the [Enter Password] screen appears, enter the Supervisor Pass-
word and tap [OK].
CSelect [Yes].
NOTENOTE
zWhen you turn on the wireless display next time, the calibration screen will 
appear. 
(Îpage 20)
1 Press the power button for one or two seconds until the 
message “Preparing to Power off…” appears.
zWhen shutting down forcefully, press the power button for four seconds 
or longer.
Shutting Down (power off the wireless display)
CF-08.book  32 ページ  ２００６年４月６日　木曜日　午後６時３８分 
						

							33
LCD (Touchscreen)
Using the Stylus
Use the stylus provided to perform operations on the 
touchscreen. The stylus is located in the stylus holder 
(A), and can be held like a pen or pencil. The following 
operations are possible on the touchscreen.
Tapping
You can select an item on the screen by tapping it with 
the stylus. This operation is called a “tap”. 
Dragging
You can drag on item on the screen by holding the sty-
lus down over the item and then moving the stylus. This 
operation is called a “drag”.
Tapping and Holding
You can tap and hold the stylus on an item to see a list 
of actions available for that item. On the pop-up menu 
that appears, tap the action you want to perform.
Right-clicking
You can execute the right click operation. (Îpage 38)
Handling the Stylus
zClean the stylus tip and screen prior to operation. Foreign particles can scratch 
the screen and impede the operation of the stylus.
zUse the provided stylus only on the screen. Using it for any other purpose may 
damage the stylus and scratch the screen.
CF-08.book  33 ページ  ２００６年４月６日　木曜日　午後６時３８分 
						

							34
LCD (Touchscreen)
Handling the Touchscreen
zUse the provided stylus with CF-08. Do not use an implement other than the 
stylus that comes with the wireless display.
zDo not place any object on the surface or press down forcefully with sharp-
pointed objects (e.g., nails), or hard objects that can leave marks (e.g., pencils 
and ball point pens).
zDo not operate the wireless display when such things as dust are on the LCD.  
Do not allow substances such as oil to contact the LCD. The cursor may not 
work properly in such cases.
Aligning the touchscreen
Align the touchscreen if the cursor does not correctly move to the position where 
the stylus touches the touchscreen of the wireless display.
ADouble-tap   on the desktop, and double-tap [Stylus].
BTap the [Calibration] tab, and tap [Recalibrate].
Rotating the screen
To rotate the screen, perform the following procedure.
ADouble-tap   on the desktop.
BDouble-tap [Rotate].
CAdd the check mark for [0 degrees (Landscape)], [90 degrees], [180 
degrees] or [270 degrees], and tap [Rotate]. 
The screen will rotate to the position selected.
Using the following procedure, you can set the screen to rotate to a preset position 
with the press of a single button. 
zHere, we will explain how to make the following settings: 
• Button to be used/push length: keyboard button/long push
• Setting angles: [0 degrees (Landscape)] and [90 degrees]
CF-08.book  34 ページ  ２００６年４月６日　木曜日　午後６時３８分 
						

							35
ADouble-tap   on the desktop.
BDouble-tap [Buttons].
CAssign [Rotate Screen] to the keyboard button, long push, and tap  . 
DDouble-tap [Rotate].
EAdd the check mark for [0 degrees (Landscape)] and [90 degrees], and tap 
.
FSave the above setting.
Refer to step 
9 of “First-time Operation” (Îpage 27).
GPress the keyboard button for more than 2 seconds.
The screen will rotate to [90 degrees]. 
If you press the keyboard button once more, the screen will return to [0 
degrees (Landscape)].
zYou can set the screen to rotate to a preset position using Quick Menu, just like 
the button setting above. (Îpage 39)
CF-08.book  35 ページ  ２００６年４月６日　木曜日　午後６時３８分 
						

							36
Battery Power
NOTENOTE
zOnce the battery is fully charged, the wireless display performs recharging only 
when the battery level becomes less than approximately 95%, so overcharging is 
avoided.
You can check the remaining battery charge using any of the following methods.
zDouble-tap   on the desktop, double-tap [Power] and tap the [Battery] 
tab.
zPress the keyboard button or USER button (Îpage 38) and run Quick Menu 
(Îpage 39).
Battery Indicator
Battery indicatorBattery status
Not litThe battery pack is not inserted or not being charged. 
Pulsing orangeCharging is in progress. 
GreenThe battery is fully-charged.
RedThe remaining battery is approximately 9% or less.
Blinking redThe battery pack or the charging circuit is not operating 
normally.
Blinking orangeThe battery cannot be charged temporarily due to the fol-
lowing reason: 
zIts internal temperature is out of the acceptable range. 
Checking the Remaining Battery Charge
CF-08.book  36 ページ  ２００６年４月６日　木曜日　午後６時３８分 
						

							37
You can reduce power consumption using the following method.
When using the battery, the wireless display can be used for a longer period of 
time.
Power conservation effects can be achieved even when the AC adaptor is connected.
zDouble-tap  on the desktop, dou-
ble-tap [Power] and tap the [Schemes] 
tab.
Power consumption can also be mini-
mized with detailed settings; for exam-
ple, by reducing the time setting for 
[Turn off LCD].
The battery pack is a consumable item so the replacement (CF-VZSU44U) will be 
necessary. If the battery operation time becomes noticeably short, replace with a 
new battery.
How to remove/insert the battery pack:Îpage 17
Replacing the Battery Pack
CF-08.book  37 ページ  ２００６年４月６日　木曜日　午後６時３８分 
						

							38
Buttons
You can display screens for frequently used 
functions and applications by pressing the key-
board button   or USER button   on this 
wireless display.
Two functions can be assigned to each button; 
one that starts up with a short push (less than 2 
seconds) and one that starts up with a long 
push (more than 2 seconds).
At the time of purchase, the following functions or applications are assigned to 
each button.
*1To execute the right click operation:
APress the USER button for more than 2 seconds.
You can use the right click once.
Each time after this, before using the right click once, execute step 
A above.
You can also execute the right click operation using Quick Menu (Îpage 39).
Customizing buttons
ADouble-tap   on the desktop and then double-tap [Buttons].
BWhen the [Buttons] screen appears, tap  , and then select the function 
name in accordance with the button positions and short/long push that you 
want to set.
CTa p  .
DSave the above setting.
Refer to step 
9 of “First-time Operation” (Îpage 27). Keyboard button
Short push Input Panel (Îpage 41)
Long push Input Panel Selector (Îpage 42)
USER button
Short push Quick Menu (Îpage 39)
Long push
Right Click*1
CF-08.book  38 ページ  ２００６年４月６日　木曜日　午後６時３８分 
						

							39
Quick Menu
Quick Menu is used to display information about the wireless display, or to enable 
frequently used functions and applications to be launched quickly without going 
through Control Panel (Îpage 53). 
At the time of purchase, Quick Menu can be 
launched with a short push of the USER button 
.
How to change Quick Menu launching method: 
Îpage 38
A. Battery
Display remaining battery level 
(Same setting for [Power] in Con-
trol Panel).
B. Wireless
Display status of wireless LAN.
C. Volume
Set and change sound volumes 
(Same setting for [Volume & 
Sounds] in Control Panel).
D. Brightness
Set and change display backlight 
brightness (Same setting for 
[Backlight] in Control Panel).E. Buttons
Start up frequently used functions and 
applications.
At the time of purchase, [Right Click]
*1, 
[Input Panel Selector] (Îpage 42), 
[Control Panel] (Îpage 53) and [Stylus 
Calibration] are set in Quick Menu.
*1To execute the right click operation:
ATap [Right Click].
You can use the right click once.
Each time after this, before using the right 
click once, execute step 
A above.
You can also execute the right click opera-
tion by pressing the keyboard button or 
USER button. (Îpage 38)
CF-08.book  39 ページ  ２００６年４月６日　木曜日　午後６時３８分 
						

							40
Quick Menu
Customizing buttons
ADouble-tap   on the desktop and then double-tap [Quick Menu].
The [QuickMenu Application Assignment] screen will appear.
BIn [1. Select Button], tap one button to which the function or application is to 
be assigned from among the four buttons. 
CIn [2. Assign a Function], tap  , and then select the function or application 
to be assigned. 
DTa p  .
ESave the above setting.
Refer to step 
9 of “First-time Operation” (Îpage 27).
CF-08.book  40 ページ  ２００６年４月６日　木曜日　午後６時３８分