Panasonic Cf30 Service Manual

9-9
9.1.16. Removing the Display  Unit
1. Remove the 2 Screws  and the 4 Screws .
2. Remove the Display Unit.
Screws : DRYN4+J10FKL
Screws : DXSB4+15FNLB
9.1.17.  Removing the LCD Rear Cabinet, 
Hinge L and R
1. Remove the 4 Screws. 
2. Remove the 2 Wireless Antenna Corner Covers.
3. Remove the 4 Screws  and 2 Screws. 
4. Remove the left and right LCD Cover Side Covers.
5. Remove the 4 Screws. 
6. Remove the LCD Rear Cabinet.
7. Remove the LCD Latch.
8. Remove the 2 Screws. 
9. Remove the Hinge L and R....

9-10
9.1.18. Removing the  Inverter PCB,  TS PCB 
and LCD Unit
1. Remove the 2 Screws. 
2. Disconnect the 3 Cables from the 3 Connectors.
3. Remove the Inverter.
4. Disconnect the 2 Cables from the 2 Connectors. 
(CN200,CN201)
5. Remove the TS PCB.
6. Remove the 2 Drop Holders.
7. Remove the LCD Unit.
Screws : DRQT26+D4FKL
9.1.19.  Removing the  Antenna  PCB L and R
1. Remove the 4 Screws .
2. Remove the W-LAN ANT Cover L and R.
3. Remove the 2 Screws. 
4. Remove the Antenna PCB L and R.
Screws :...

9-11
9.2. Reassembly Instructions
9.2.1.  Attention when CF-30  series  is  repaired
• Please execute writing BIOS ID when you exchange the Main Board.
• Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.
9.2.2.  Setting the  Antenna PCB L and R
1. Set the Antenna PCB L and R using the 2 Screws. 
2. Fix the W-LAN ANT Cover L and R using the 4 Screws.

Screws : DRHM5054XA
Q  Arranging the Antenna L and R Cables




LCD Rear Cabinet...

9-12
9.2.3. Setting the  Inverter  PCB, TS PCB and LCD Unit
1. Set the LCD Unit to the LCD Front Cabinet in order.
2. Attach the 2 drop holders.
3. Connect the Cable to the Connector. (CN200,CN201)
4. Connect the 3 Cables to the 3 Connectors.
5. Fix the Inverter PCB using the 2 Screws. 
Screws : DRQT26+D4FKL
Q  Preparation of Inverter

LCD Unit
LCD Front Cabinet Inverter PCB
TS PCB
LCD Drop Holder
LCD Drop 
Holder
A
B
AB
C
C
to Connector
(CN200)
Connector
(CN200)Connector
(CN201)
Wrap Inverter Shield...

9-13
Q
 Assembly of LCD Unit
9.2.4.  Setting the LCD  Rear Cabinet, Hinge L and R
1. Fix the Hinge L and R using the 2 Screws. 
2. Set the LCD Latch.
3. Fix the LCD Rear Cabinet using the 4 Screws.  No1 to
No4
4. Fix the left and right LCD Cover Side Cover using the 4 Screws  and 2 Screws. 
5. Fix the 2 Wireless Antenna Corner Cover using the 4 Screws. 
Note: Tighten the Screws in the numbered order (No1 to No4).
Screws : DRHM5054XA
Screws : DRSB26+10HKL
Screws : DRSB4+10FKL
Screws : DRYN4+J10KLT
Attach...

9-14
9.2.5. Setting the Display  Unit
1. Fix the Display Unit using the 4 Screws.  No1 to No4
2. Fix the Display Unit using the 2 Screws.  No1, No2
Note: Tighten the Screws in the numbered order (No1 to No2).
Tighten the Screws in the numbered order (No1 to No4).
Screws : DRYN4+J10FKL
Screws : DXSB4+15FNLB
9.2.6.  Setting the Handle and Power SW
1. Set the WM SW using the 2 Screws. 
2. Set the Power SW.
3. Set the Handle.
4. Fix the Handle Base L and R using the 2 Screws. 
Screws : DRSN4+6FKLT
Screws :...

9-15
9.2.7. Setting the Palm  Top Cover Sheet,  Palm Top Cover,  Touch Pad Adhesion Seat,  Touch
Pad SW Knob, LED PCB And SW LED PCB
1. Set the SW LED PCB.
2. Attach the Power LED Packing Sheet to the LED Spacer
Sheet.
3. Attach the LEDX6 Spacer Sheet on the SW LED PCB.
4. Fix the SW LED PCB using the Screw. 
5. Attach the PW LED Sheet.
6. Pass the Cable of LED PCB through the hole 1 on the Top Cabinet, then set the LED PCB.
7. Attach the LES Spacer Sheet on the LED PCB.
8. Set the touch Pad SW Knob In...

9-16
Q
 Assembly of Power SW
Q  Assembly of Palm Top Cover
12    2
25    2
10    1
3    5
Attach the Battery Cushion
Attach the DC Gasket
Tighten of Screw  
Power SW LED 
Panel is set
FPC Power SW is set
Safety Working 
Attach the TP 
FPC Tape Cable Power
Connection* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2\
 Battery Pack Insertion Slot
Attach the Battery Slide Sheet (on Battery Cushion)Avoid air leaking into it.  Avoid coming off 4 corners.
Fit to the line.
Ensure...

9-17
9.2.8. Setting the  I/O  PCB
1. Open the Connector Cover and Lid Cover.
2. Fix the I/O PCB using the 4 Screws.  No1 to No4
3. Fix the I/O PCB using the 4 Screws.  No1 to No4
Note: Tighten the Screws in the numbered order (No1 to No4).
Screws : DFHE5058ZB
Screws  : DRHM5104ZA
9.2.9.  Setting the SD  PCB, Express Card
and PCMCIA Card
1. Fix the PCMCIA Card using the 4 Screws. 
2. Fix the Express Card using the 4 Screws. 
3. Fix the SD PCB using the 2 Screws. 
Screws : DRQT26+D4FKL
Screws :...

9-18
9.2.10. Setting the Ma in PCB
1. Fix the Main PCB using the 7 Screws  and Screw.
 No1 to No8. 
2. Set the Modem Cable.
3. Connect the Cable to the Connector (J2) and fix the MDC.
4. Attach the Tape.
5. Attach the 1394 Sheet.
6. Fix the MDC using the 2 Screws. 
7. Fix the Modem LAN Case using the 2 Screws. 
8. Attach the 2 Modem Cable Sheets.
9. Fix the ICH Plate using the 3 Screws  and Screw
.
10. Connect the Cable to the Connector (CN4,CN11) 11. Attach the Tape.
12. Attach the Coin Battery.
13....