Panasonic Color CCTV Camera Wv Cf314 Wv Cw324 Operating Instructions

							21
Camera system setting [SYSTEM SETUP] 
Performs  the  settings  relating  to  the  camera  system  such  as  synchronization,  alarm  input/output  terminal  and  privacy  zone.  The 
following settings can be configured on the “SYSTEM SETUP” screen displayed from the top screen. 
Refer to page 5 for how to call up the screen. 
10. Synchronization method [SYNC]
Only internal synchronization (INT) can be used. 
Multiplexed vertical drive (VD2) synchronization cannot be used.
11. Privacy zone setting [PRIVACY ZONE]
When undesired portions in the camera shooting area (on the screen) exist, those portions (privacy zone) can be set to be hidden. Up 
to 8 portions can be specified for the privacy zone. 
ON (1): Grays the zone. 
ON (2): Mosaics the zone. 
OFF (default): Displays the zone normally. 
Follow the procedure below to set the privacy zone. 
Note:
	 •	 The	privacy	zone	function	is	disabled	at	initializing	the	unit,	i.e.	right	after	turning	on	the	power.	
  **ZONE NUMBER 1 /8** 
PUSH SETPOSITION
UPPER LE FT
 RET TOP END DEL 
            -     +ZONE LEVEL  ..I.... 2
“SYSTEM SETUP” screen
“ZONE NUMBER” screen
 ON(2)
    **SYSTEM SETUP** 
SYNC          INT
PRIVACY ZONE
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN   OFF
  -     +
LDC           I......  0
 RET TOP END
Step 1
Move the cursor to “PRIVACY ZONE”, select “ON (1)” or “ON (2)”, and press the [SET] button. 
→  The “ZONE NUMBER” screen appears. 
Step 2
Move the cursor to the number at the right of the title and select the z\
one number using the [ RIGHT] or [LEFT] button. 
Step 3
Move the cursor to “POSITION” and press the [SET] button. 
Step 4
Press  the  [UP],  [DOWN ],  [RIGHT],  and  [LEFT]  buttons  to  determine  the  left  upper  position  of  the  zone  to  be  set  and  press  the  [SET] 
button. 
“SYSTEM SETUP” screen
    **SYSTEM SETUP** 
SYNC          INT
PRIVACY ZONE  OFF
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN   OFF
   -     +
LDC           I......  0
 RET TOP END 
						

							22
Step 5
Press the [UP], [DOWN ], [RIGHT], and [LEFT] buttons to determine the lower right position of the zone to be set and press the [SET] 
button. 
→  An asterisk “*” will be displayed after the number and the zone s\
etting will be saved. 
Step 6
When  “ON  (2)”  is  selected  for  “PRIVACY  ZONE”,  the  mosaic  level  may  be  adjusted.  The  mosaic  level  may  be  set  through  “ZONE 
LEVEL”. (Range: 1 to 4) 
Note:
	 •	 To	delete	a	zone,	select	the	zone	number	and	press	the	[SET]	button	after	moving	the	cursor	to	“DEL”.	
	 •	 To	change	the	settings	of	a	zone,	select	the	zone	number	and	repeat	from	step	3.	
12. Image stabilizer setting [STABILIZER]
Whether or not to enable the image stabilizer is determined. 
This function is effective for the case that the camera is installed at \
a place with slight shaking. 
ON: Enables the image stabilizer. 
OFF (default): Disables the image stabilizer. 
Important:
	 •	 When	 “ON”	is	selected	 for	the	 image	 stabilizer,	 the	view	 angle	 becomes	 narrower	and	the	resolution	 becomes	lower.	When	“ON”	
is selected for the image stabilizer, check the view angle and resolution at camera installation. 
	 •	 The	image	stabilizer	function	may	not	work	for	the	following	subjects	or	conditions.
	 	 •	Dark	subject	
	 	 •	Less	contrasty	subject	(e.g.	white	wall)	
	 	 •	Subject	shaking	at	excessive	speed		
	 	 •	Large	amplitude	image	shaking
13. Electronic zoom setting [EL-ZOOM] 
Whether or not to use the electronic zoom is determined. 
ON: Uses the electronic zoom. 
OFF (default): Does not use the electronic zoom. 
When “ON” is selected, the zoom factor and the panning/tilting set\
tings can be configured. 
Follow the procedure below.
      **EL-ZOOM**      **EL-ZOOM****EL-ZOOM**
PUSH SET
PUSH SET
ZOOM
PAN/TILT
PUSH SET
PUSH SETZOOM
PAN/TILT
PUSH SET
PUSH SETZOOM
PAN/TILT
U ZOOM D U TILT D/L PAN 
R
“SYSTEM SETUP” screen “EL-ZOOM” screen  Pan/tilt setting screen
Zoom setting screen
 RET TOP END  RET TOP END RET TOP END
 OFF
    **SYSTEM SETUP** 
SYNC          INT
PRIVACY ZONE
STABILIZER    OFF
EL-ZOOM       ON
UPSIDE-DOWN   OFF
  
-     +
LDC           I......  
0
 RET TOP END
Step 1
Move the cursor to “EL-ZOOM” and select “ON” and press the [SET] button. 
→  The “EL-ZOOM” screen appears.  
						

							23
Step 2
Move the cursor to “ → PUSH SET” of “ZOOM” and press the [SET] button. 
→  The zoom setting screen appears. 
Step 3
Adjust the angular field of view by changing the electronic zoom factor (up to 2x) using the [UP] or [DOWN] button, and press the [SET] 
button. 
Note:
	 •	 When	the	zoom	factor	is	incremented,	resolution	will	be	deteriorated.	
Step 4
Move the cursor to “ → PUSH SET” of “PAN/TILT” and press the [SET] button. 
→  The pan/tilt setting screen appears. 
Step 5
Press the [UP], [DOWN], [RIGHT], and [LEFT] buttons to determine the position of the area to be set and press the [SET] button. 
The position can be changed in the range of zoom factor set in the zoom \
setting screen. 
14. Upside-down setting [UPSIDE-DOWN] 
ON: The video image can be reversed upside down. 
OFF (default): The video image cannot be reversed upside down.
15. Lens distortion correction [LDC]
The image may be distorted depending on the lens used and the zoom factor. By adjusting the lens distortion correction setting, the 
distorted image can be converted to match the square monitor and achieve effects desired by the user. 
Note:
	 •		 	Depending	on	the	lens	used,	complete	correction	may	not	be	achieved.	 
						

							24
Back focus setting [BACK-FOCUS SETUP] CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
Selects  the  back  focus  setting  type  and  performs  fine  adjustment.  The  following  setting  can  be  configured  on  the  “BACK-FOCUS 
SETUP” screen displayed from the top screen. Refer to page 5 for how to call up the screen.
The lens adjustment shall be performed before the back focus adjustment.
16. Auto back focus setting [ABF]
Move the cursor to “→ PUSH SET” of “ABF” and press the [SET] button.
→   The  auto  back  focus  function  provides  back  focus  adjustment  to  automatically  focus  on  a  subject  located  in  the  center  of  the 
screen.
17. Manual back focus setting [MANUAL-ADJ]
To fine adjust the back focus, move the cursor to “MANUAL-ADJ”, press the [SET] button, and press the [RIGHT] or [LEFT] button to 
adjust the back focus manually.
18.  Auto  back  focus  settings  for  switching  between  color  and  black-and-white 
modes [CL ↔
B/W]
Move the cursor to “C/L ← →B/W” and select the back focus adjustment type from the following:
AUTO:   Adjusts  the  back  focus  function  automatically  and  corrects  out  of  focus  when  switching  between  color  and  black-and-white 
images.
FIX (default): The back focus function will not adjust automatically when switching be\
tween color and black-and-white images.
Important:
	 •	 The	 auto	back	 focus	 function	 is	used	 for	back	 focus	 adjustment	 at	installation	 and	for	focus	 correction	 at	switching	 between	the	
color  and  black-and-white  modes  after  installation.  This  function  is  not  a  function  that  is  supposed  to  be  operated  continuously 
such as the auto focus function.
	 •	 When	 focus	missing	 occurs	due	to	secular	 change	 in	the	 lens	 and	installation	 environment	 or	peripheral	 temperature	 change,	the	
back focus adjustment is required again.
	 •	 The	following	are	recommendation	for	back	focus	setting	in	accordance	with	subjects.
For such case (subject conditions) Select this (recommendation)
Back focus adjustment“C/L←  → B/W” switching
	 •	 Normal	subject	 “ABF” “AUTO”
	 •	 Frequently	moving	subject	 Fine  adjustment  with  “MANUAL-ADJ”  after 
“ABF”“FIX”
	 •	 Subject	with	remarkable	illuminance	change
 
	 •	 Subject	with	low	illuminance	
	 •	 Too	bright	or	reflective	subject	
	 •	 Subject	through	a	window
	 •	 Place	where	the	lens	easily	becomes	dirty
	 •	 Subject	with	less	contrast	such	as	white	wall
	 •	 Subject	with	remarkable	depth
	 •	 Subject	with	heavy	flicker
	 •	 Subject	with	horizontally	parallel	lines	such	as	a	shutter
Note:
	 •	 The	back	focus	adjustment	can	be	also	performed	through	the	operation	buttons.	
“BACK-FOCUS SETUP” screen
    **BACK-FOCUS SETUP**  ABF           PUSH SET
MANUAL-ADJ
C/L  B/W      FIX
 RET TOP END 
						

							25
Special menu setting [SPECIAL SETUP] 
The special menu setup is performed including the setting of the camera image quality and the communication configuration when a 
receiver is used. The following settings are to be configured on the “SPECIAL SETUP” screen displayed from the top screen. 
Refer to page 5 for how to call up the screen. 
19. Chroma level adjustment [CHROMA GAIN] 
Press  the  [RIGHT]  or  [LEFT]  button  to  adjust  the  color  density  of  the  camera  image.  When  the  level  indicator  moves  in  the  “+” 
direction,  the  color  becomes  deeper,  and  when  the  level  indicator  moves  in  the  “–”  direction,  the  color  becomes  lighter.  Be  sure  to 
view a vector chromaticity indicator or a video monitor when the adjustment is performed.\
 
20. Aperture level adjustment [AP GAIN]
Press  the  [RIGHT]  or  [LEFT]  button  to  adjust  the  image  quality.  When  the  level  indicator  moves  in  the  “+”  direction,  the  image 
becomes sharper, and when the level indicator moves in the “–” direction, the image becomes softer. Be sure to view a video monitor 
when the adjustment is performed.
Note:
	 •		Moire	(interference	 fringes)	may	be	observed	 when	shooting	 a	subject	 with	fine	pattern	 such	as	a	carpet	 or	a	curtain.	 In	such	 a	
case, move the indicator in the “-” direction to reduce moire. 
21. Pedestal level adjustment [PEDESTAL] 
Press  the  [RIGHT]  or  [LEFT]  button  to  adjust  the  pedestal  level  of  the  camera.  When  the  level  indicator  moves  in  the  “+”  direction, 
the  image  becomes  brighter,  and  when  the  level  indicator  moves  in  the  “–”  direction,  the  image  becomes  darker.  Be  sure  to  view  a 
waveform monitor or a video monitor when the adjustment is performed. 
22. Pixel compensation [PIX OFF] 
Flaws of pixel in the displayed camera image are corrected. Up to 16 points can be corrected. 
CW324L
CW314L
CW304L
CF314L
CF304L  In order to see more clearly the flaws of pixel, please cover the lens with objects to make\
 the image black totally. 
Follow the procedure below. 
      **PIX OFF**
  1     2     3     4
  5     6     7     8
  9    10    11    12
 13    14    15    16
1
DEL 000 000
“SPECIAL SETUP” screen “PIX OFF” screenPixel compensation positioning scree n
 RET TOP END
   **SPECIAL SETUP**
CHROMA GAIN   ...
.I..160
AP GAIN        ..I.
... 32
PEDESTAL       .I.
.
... 16
              -      +
PIX OFF
CAMERA RESET  PUSH SET
 SER.NO. XXXXXXXX
 RET TOP END
“SPECIAL  SETUP” screen
   **SPECIAL SETUP**
CHROMA GAIN    ...
.I..160
AP GAIN        ..I.
... 32
PEDESTAL       .I.
.
... 16
              -      +
PIX OFF
CAMERA RESET  PUSH SET
 SER.NO. XXXXXXXX
 RET TOP END 
						

							26
Step 1
Move the cursor to “PIX OFF” and press the [SET] button. 
→  The “PIX OFF” screen appears. 
Step 2
Select a number (1 to 16) with which a pixel compensation point is registered and press the [SET] button. 
→  The pixel compensation positioning screen appears. 
Step 3
Press the [UP], [DOWN], [RIGHT], and [LEFT] buttons to move the crosshair cursor to the center of the flaw to be corrected and press 
the [SET] button. 
→   The  flaw  is  corrected  and  the  pixel  compensation  point  is  registered.  The  “PIX  OFF”  screen  appears  again.  An  asterisk  “*”  is 
attached at the right side of the number when registration is completed. The coordinate is expressed in figures. 
Note:
	 •		To	 clear	the	registered	 pixel	compensation	 point,	move	the	cursor	 to	“1”	 of	the	 right	 of	“DEL”,	 use	the	[RIGHT] and [LEFT] buttons 
to select the number with which the target pixel compensation point is registered and press the [SET] button. The registered pixel 
compensation point is cleared, and an asterisk “*” at the right side of the number disappears\
. 
23. Default resetting [CAMERA RESET] 
The settings in the setup menu are restored to the default settings. 
Move the cursor to “ → PUSH SET” of “CAMERA RESET” and hold down the [SET] button for more than 2 seconds to enter the next 
screen. 
To return to the previous screen without resetting, move the cursor to “NO” and press the [SET] button. To restore the default settings, 
move the cursor to “YES” and press the [SET] button. 
Note:
	 •		The	data	of	the	registered	pixel	compensation	points	is	not	cleared.		
	 •		To 	set 	whether 	to 	reset 	the 	camera, 	select 	“YES” 	or 	“NO” 	by 	using 	the 	[SET] 	button. 	To 	set 	with 	a 	controller, 	refer 	to 	the	
instruction manual of the controller. 
24. Serial number viewing [SER.NO.] 
Displays the serial number of this product.  
						

							27
Camera language selection [LANGUAGE SETUP]
A  language  for  the  setup  menu  is  selected  from  the  following:  The  language  selection  can  be  made  on  the  “LANGUAGE  SETUP” 
screen displayed from the top screen. 
Refer to page 5 for how to call up the screen.  
Move the cursor to “LANGUAGE” and press the [RIGHT] or [LEFT] button to select the target language, then move the cursor to “SET”, 
and press the [SET] button. 
Select the target language from the following. 
JAPANESE/ENGLISH (default)/FRANÇAIS/ESPAÑOL/DEUTSCH/ITALIANO/PУCCKИЙ/
中文  
Note:
	 •		When	the	language	is	changed,	the	specified	camera	title	is	cleared.	
“LANGUAGE SETUP” screen 
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END 
						

							28
Shortcut operation 
Use  of  a  system  controller  with  the  “Camera  function”  button  allows  users  to  perform  the  shortcut  settings  with  use  of  the  numeric 
keypad and camera function button. The available shortcut operations wit\
h this unit are shown as follows. 
System	controller	operationSetting contents
[9] + [0] + [Camera function]  Black-and-white control (D&N) ON
[9] + [1] + [Camera function]  Black-and-white control (D&N) OFF
[9] + [2] + [Camera function]  Black-and-white control (D&N) AUTO1
[9] + [3] + [Camera function]  Camera title (CAMERA ID) ON
[9] + [4] + [Camera function]  Camera title (CAMERA ID) OFF
[9] + [8] + [Camera function]  Electronic zoom ON
[9] + [9] + [Camera function]  Electronic zoom OFF
[1] + [6] + [8] + [Camera function]  Black-and-white control (D&N) AUTO2
[1] + [6] + [9] + [Camera function]  Iris of lens (IRIS) OPEN
[1] + [7] + [0] + [Camera function]  Iris of lens (IRIS) CLOSE
[1] + [7] + [1] + [Camera function]  Electronic shutter (SHUTTER) ON 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L 
[1] + [7] + [2] + [Camera function]  Electronic shutter (SHUTTER) OFF 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L 
[1] + [7] + [3] + [Camera function]  Electronic shutter speed, 1 step faster 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L 
[1] + [7] + [4] + [Camera function]  Electronic shutter speed, 1 step slower 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L 
[1] + [7] + [5] + [Camera function]  Gain adjustment (AGC) ON
[1] + [7] + [6] + [Camera function]  Gain adjustment (AGC) OFF
[1] + [7] + [7] + [Camera function]  Electronic sensitivity up (SENS UP) FIX ON 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L 
[1] + [7] + [8] + [Camera function]  Electronic sensitivity up (SENS UP) FIX OFF 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L 
[1] + [7] + [9] + [Camera function]  Electronic sensitivity, 1 step up (FIX)  
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L 
[1] + [8] + [0] + [Camera function]  Electronic sensitivity, 1 step down (FIX)  
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L
 
CW324L
CW314L
CW304L
CF314L
CF304L 
[1] + [8] + [1] + [Camera function]  Electronic sensitivity up (SENS UP) AUTO ON
[1] + [8] + [2] + [Camera function]  Electronic sensitivity up (SENS UP) AUTO OFF
[1] + [8] + [3] + [Camera function]  Electronic sensitivity, 1 step up (AUTO) 
[1] + [8] + [4] + [Camera function]  Electronic sensitivity, 1 step down (AUTO)
[1] + [9] + [0] + [Camera function]  Time for switching at D&N AUTO, 2 seconds 
[1] + [9] + [1] + [Camera function]  Time for switching at D&N AUTO, 10 seconds
[1] + [9] + [2] + [Camera function]  Time for switching at D&N AUTO, 30 seconds 
[1] + [9] + [3] + [Camera function]  Time for switching at D&N AUTO, 60 seconds 
[2] + [0] + [1] + [Camera function]  Image stabilizer (STABILIZER) ON 
[2] + [0] + [2] + [Camera function]  Image stabilizer (STABILIZER) OFF
[2] + [1] + [3] + [Camera function]  Scene file 1
[2] + [1] + [4] + [Camera function]  Scene file 2
[2] + [1] + [5] + [Camera function] Gain (AGC), 1 step up 
[2] + [1] + [6] + [Camera function] Gain (AGC), 1 step down 
						

							http://panasonic.net
Importer's name and address to follow EU rules:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg F.R.Germany
© Panasonic System Networks Co., Ltd. 2013 sL0313-0    PGQP1452ZA    Printed in Chinahttp://panasonic.net
Importers name and addr ess to follow EU rules:
Panasonic T esting Centre
Panasonic Marketing Eur ope GmbH
Winsber gring 15, 22525 Hamburg  F.R.Germany
© Panasonic System Networks Co., Ltd. 2011
sC1111-0       PGZC1027ZA
http://panasonic.net
Importers name and addr ess to follow EU rules:
Panasonic T esting Centre
Panasonic Marketing Eur ope GmbH
Winsber gring 15, 22525 Hamburg  F.R.Germany
© Panasonic System Networks Co., Ltd. 2011
sC1111-0       PGZC1027ZA
http://panasonic.net
Importers name and addr ess to follow EU rules:
Panasonic T esting Centre
Panasonic Marketing Eur ope GmbH
Winsber gring 15, 22525 Hamburg  F.R.Germany
© Panasonic System Networks Co., Ltd. 2011
sC1111-0       PGZC1027ZA