Panasonic Color CCTV Camera Wv Cw500 WV CW504SE Series Installation Guide

31
Optional Heater Unit WV-CW5H (option)
Installing  the  heater  unit  enables  the  camera  to  operate  in  a  low-temperature  environment  below 
–30  °C.  The  heater  turns  on  automatically  when  the  temperature  inside  the  camera  drops  below 
+10  °C  and  turns  off  when  the  temperature  rises.  A  small  fan  inside  the  unit  will  minimize  conden-
sation on the surface of the enclosure caused by changes in ambient temperature unless tempera-
tures change too rapidly.  Important:...

32
About the setup menus
Performing  each  setting  item  in  the  setup  menu  should  be  completed  in  advance  to  use  this  unit. 
Perform the settings for each item in accordance with the conditions of the camera shooting area. 
Refer to the operating instructions (PDF) for further information. 
Setup menu list
Setup itemDescription
CAMERA ID This item specifies the camera title. The camera title that indicates th\
e 
camera location and other information about the camera is created 
with...

33
Setup itemDescription
SPECIAL CHROMA GAIN Adjusts the chroma level. 
AP GAIN Adjusts the aperture level. 
PEDESTAL Adjusts the pedestal (brightness) level. 
PIX OFF Corrects image defects such as flaws. 
CAMERA RESET Restores the settings in the setup menu to the default settings. 
SER.NO. Displays the serial number of this unit. 
LANGUAGE Selects a language to be used in the setup menu.
     

34
Screenshot 2
The  setup  mode  changes  to  "ENABLE",  and 
the setup menu becomes ready to be set. 
Basic operation
The description below explains how to operate the setup menu basically. 
The operations in the setup menu are performed with the operation buttons (+ page 12) after call-
ing up the setup menu on the connected video monitor.
The operations in the setup menu can also be performed through the system controller (option). 
Screenshot 1
Hold  down  the  setting  button  for  more...

35
Screenshot 3
The  selected  setup  screen  in  the  setup  menu 
appears on the screen. 
Note:
	 •	 If 	the 	top 	screen 	of 	the 	setup 	menu 	is	
called  up  with  the  operation  buttons  while 
a  camera  image  is  displayed,  the  setup 
mode  is  always  "DISABLE"  to  prevent 
operation  errors.  To  configure  the  settings 
in  the  setup  menu,  change  the  setup 
mode to "ENABLE". 
	 •	 The	cursor	is	a	reversely	highlighted	part.	
    
    **CAMERA SETUP** 
SCENE1
 ALC...

36
Screen transition diagram
 MODEL   WV-CW500 SERIES
CAMERA ID     OFF
CAMERA   
SYSTEM
BACK-FOCUS   
SPECIAL
LANGUAGE
 
 END   SETUP DISABLE
    **CAMERA SETUP** 
SCENE1
 ALC          ALC    
 SHUTTER      OFF
 AGC          ON(HIGH)
 SENS UP      OFF
 WHITE BAL    ATW1
 DNR          HIGH
 BW MODE      AUTO1
 i-VMD
 RET TOP END
    **SYSTEM SETUP** 
SYNC          INT
LENS          PANASONIC
PRIVACY ZONE  OFF
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN   OFF
 RET TOP END
  **BACK-FOCUS SETUP**  
ABF...

37
Troubleshooting
Before asking for repairs, check the symptoms with the following table. 
Contact  your  dealer  if  a  problem  cannot  be  solved  even  after  checking  and  trying  the  solution  in  the 
table or a problem is not described below. 
SymptomCause/solutionReference 
pages
No image displayed
•		 Are	the	power	cord	and	coaxial	cable	
connected appropriately?
→   Check whether the connection is 
appropriately established.  29
•		 Is	the	adjusting	monitor	connected?
→   Check whether...

38
Specifications
• Basic
Power source: WV-CW500: 220 to 240 V AC 50 Hz 
    WV-CW504: 24 V AC 50 Hz, 12 V DC
Power consumption:  WV-CW500:  5.1 W (without heater unit) 
16 W (with heater unit)
    WV-CW504: 24 V AC:  3.4 W (without heater unit) 
14 W (with heater unit)
     12 V DC: 280 mA*
Ambient operating temperature:  –10 °C to +50 °C
    –30 °C to +50 °C**
Ambient operating humidity:  Less than 90 % (no condensation)
Water resistance:    Camera: IEC60529 (IP66)***
Shock resistance:   50J,...

39
   When using smoke dome cover (option): 
    Color Mode:  0.2 lx at F1.4 WIDE 
0.006 lx (sensitivity up x32, at F1.4 WIDE)*
    BW mode:   0.02 lx at F1.4 WIDE 
0.0006 lx (sensitivity up x32, at F1.4 
WIDE)*
    * Converted value
Signal-to-noise ratio:   50 dB (AGC Off)
Dynamic range:  54 dB typ. (Super Dynamic 5 ON)
Monitor output:  VBS: 1.0 V [p-p]/75 Ω, PAL, RCA jack
Functions:
  Camera title:    Up to 16 characters (alphanumeric characters, marks)
  Light control mode setting:  ALC/ALC+
  Super...

40
Standard accessories
CD-ROM*  ................................................................... 1 pc.
Installation Guide (this book)   ....................................... 1 pc.
*The CD-ROM contains the operating instructions (PDF). 
The following parts are used during installation procedures.
Base cover   ................................................................. 1 pc.
Camera mount bracket   ............................................... 1 pc.
Fixing screw for camera mount bracket...