Panasonic Cz Rtc4cz Rtc3 Operating Instructions Manual

25(EN)
Temp range
4Select the item and set to [].
▲ ▼ → ◄ ► → 
 
5
Set the temperature range.
▲ ▼ → ► → ▲ ▼ → 
 →  
(Press 2 times to fi nish.)
Setting range
•  Cool/Dry: 18 °C to 30 °C
•  Heat: 16 °C to 30 °C
•  Auto: 17 °C to 27 °C
  To set in series     Repeat from step 4 without pressing .
Note
•  Temp auto return
When [Return type] is set to [Saving], this functions only when the temperature set in step 
5 saves more energy than the changed temperature.
e.g. When Cool 26 °C is set and the...

26(EN)
Energy Saving
  Auto shutoff
When the operation is stopped at a specifi ed time (e.g. closing time) and 
resumed afterwards, this function detects the operation status at regular 
time intervals and stops operation automatically.
Detect the operation status at regular time intervals and stop the operation automatically.
(e.g. 60 min)
ON
OFF 21:00 22:08DetectDetect Detect
23:009:00 60 min 60 min 60 min
Closing timeOpening time
Auto shutoff in effect
Leaves the 
shop without 
turning off 
A/C.If...

27(EN)
Stop time
Time to stop operation (Time when Auto shutoff is activated)
5
Set.
hour               minute
▲ ▼ → ► → ▲ ▼ → 
 →  
(Press 2 times to fi nish.)
End time
Time when Auto shutoff stops
5
Set.
hour               minute
▲ ▼ → ► → ▲ ▼ → 
 →  
(Press 2 times to fi nish.)
Timer
Time interval to detect operation status after 
[Stop time]
5
Set.
▲ ▼ → 
 →  
(Press 2 times to fi nish.)
•  10 min to 180 min
(by the 10 min) 

28(EN)
Energy Saving
  Schedule peak cut
This reduces the operation capacity for 
the specifi ed time period.
1
Display the menu screen.
  To return to the last screenPress .
  To return to the top screenPress  2 times.
2
Select [Energy saving].
▲ ▼ → 
3
Select [Schedule peak cut].
▲ ▼ → 
4
Enter the password.
▲  ▼ → ► → 
(Repeat)
5Set [Select enable/disable] to [].
▲ ▼ → ◄ ►
6
Select [Set schedule].
▲ ▼ → 
 
7
Change the setting.
Select the fi eld to register.
▲ ▼ → 
 
Large
Small
11:00 13:00 16:00...

29(EN)
8
Set the start time and end time.
▲  ▼ → ► → ▲ ▼ → 
(Repeat)
9
Select the operation capacity.
▲ ▼ → 
 →  
(Press 2 times to fi nish.)
  To set in seriesRepeat from step 4 without pressing .
  To change• Select the fi eld to change in step 7 
above.
• Select [Change].
▲ ▼ → 
•  Following the above steps 8 to 9, 
select the start time, end time and 
operation capacity.
  To delete• Select the fi eld to delete in step 7 
above.
• Select [Delete].
▲ ▼ → 
• Select [YES].
◄ ► →  →  
(Press 2 times to fi...

30(EN)
Energy Saving
  Repeat off timer
This stops operation after a certain 
period of time each time operation 
is performed.
(e.g. When forgetting turning off)
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Energy saving].
▲ ▼ →  
3
Select [Repeat off timer] and set to 
[
].
▲ ▼ → ◄ ► → 
4
Set the timer to stop.
▲ ▼ → 
 →  
(Press 2 times to fi nish.)
•  10 min to 180 min
(by the 10 min)
ON
OFF 60 min
Finishes 
working...

31(EN)
Outing Function
This function prevents the room temperature from rising too high 
(or dropping too low) when no one is in the room due to outing, etc.
  
  
  
  
•  
  
•  
• •  
 
• 
 
  
 
 
     

32(EN)
Outing Function
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Outing function]
▲ ▼ → 
3
Select [Select enable/disable] 
and set to [
].
▲ ▼ → ◄ ► → 
4
Select [Set lower/upper limit temp.].
▲ ▼ → 
5
Set the temperature range.
▲ ▼ → ► → ▲ ▼ → 
 →  
(Press 2 times to fi nish.) 

33(EN)
Initial Settings  Clock     Clock type     Operation lock
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Initial settings].
▲ ▼ → 
3
Select the item to set.
▲ ▼ → 
Clock
4
Set the date and time.
▲ ▼ → ► → 
 →      (Repeat)
Clock type
4
Select the type to display.
▲ ▼ → 
 →   
(Press 2 times to fi nish.)
AM/PM
24 h
Operation lock
4
Select the type of lock and set to 
[
].
▲ ▼ → ◄ ► →  
 
(Press 2 times to 
fi nish.)...

34(EN)
Initial Settings
The room to which the remote controller belongs can 
be easily identifi ed.
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Initial settings].
▲ ▼ → 
3
Select [Controller name].
▲ ▼ → 
4
Enter the name. (Repeat the same 
procedure for all characters.)
▲ ▼ → ◄ ► → •  Up to 16 characters.
(Space is included in the number of 
characters.)
  To change the character type
Select the character type with ▲ ▼ 
◄...