Panasonic Digital Disk Recorder Wj Hd200 Operating Instructions

							71
Mail Setup (MAIL SETUP)
8Alarm Mail Setup (ALARM MAIL SETUP)
Sending Mail (SEND MAIL)
OFF: 
Does not send.
ON: Sends an e-mail to a maximum of four recipi-
ents when an alarm operates.
Attaching Alarm Image (ATTACH ALARM IMAGE)
OFF:
Does not attach.
ON:Attaches the image of the alarmed channel to
the mail.
Mail Server Address (MAIL SERVER ADDRESS)
Enter from the keyboard.
Sender Address (FROM ADDRESS)
Enter from the keyboard, and click the SET button.
8Set Mail Address (SET MAIL ADDRESS)
Enter from the keyboard, and click the [SET] button. 
A maximum of four addresses can be set.
8Delete Mail Address (DELETE MAIL ADDRESS)
Enter or select the address you wish to erase,
and click the [DELETE] button.
Note:Use the VIEW.HTML to open the attached image
and view it in the normal aspect. Otherwise, it will
be vertically reduced to half size.
Network Video Setup
(NETWORK VIDEO SETUP)
8Live & Playback Image Setup (LIVE & PLAY
IMAGE SETUP)
Video Rate (VIDEO RATE)
Applicable rates: 
FAST, MIDDLE, SLOW, VERY
SLOW 
Click the [SET] button.
8Live Sequence Setup (LIVE SEQUENCE SETUP)
Use Sequence (USE SEQUENCE)
OFF: 
Does not run the sequence.
ON: Runs the sequence.
Auto Skip (AUTO SKIP)
OFF: 
Displays any step where no video is input as
a blackout screen.
ON: Skips any step where no video is input.
Camera Channel (CAM CH)
Available channels: 
CH1 - CH8, OFF
Duration (TIME)
Available durations: 
FAST, MIDDLE, SLOW, VERY
SLOW
Click the [SET] button. 
						

							72
qMain Control Panel Tab
Opens the main control panel.
wAlarm List Tab
Opens the alarm list. 
eNetwork Status Display
LIVE, LIVE SEQ, PLAY, >> (FF), 
						

							73
@2Next Frame Button (NEXT FRAME)
Forwards the frame one step to the next while pausing.
@3Recording Button (REC)
Starts recording.
@4Recording Stop Button (REC STOP)
Stops recording.
!7Fast Forward Button (FF)
Fast-forwards the recorded image on the WJ-HD200 to
the end position.
!8To the Latest Frame Button (TO LATEST)
Jumps the recorded image to the latest frame of the
record.
!9Previous Frame Button (PREV FRAME)
Returns the frame one step to the previous.
@0Pause Button (PAUSE)
Pauses the playback image.
@1Stop Button (STOP)
Stops playbacks including REW, PREV FRAME, PAUSE,
PLAY, NEXT FRAME, and FF.
Main Control Panel
8Camera Selection Button (Camera Select) 
Click any of the buttons. 
The selected camera channel will be displayed in the
image area.
8Multiscreen Selection Button (Multiscreen Select)
Clicking the button displays the respective multiscreen.
8Live Sequence Button (LIVE SEQUENCE)
Clicking the [LIVE SEQUENCE] button runs a series of
live images in the preset sequence and for the preset
display time.
8Alarm Reset Button (ALARM RESET)
The activated alarm event is reset.
12
8
3 
						

							74
8Time & Date Search Button (TIME&DATE
SEARCH)
Clicking the button will display the time and date search
dialog.
1. Specify the date, time, and channel. 
2. Click the [SEARCH] button.
The image will be searched, and displayed in the
image area.
Note:Searching may take 18 seconds at worst particu-
larly when the recorder runs simultaneous recording
and playback, and/or when the targeted image is of
small size.
8Camera Control View Button (CAMERA CONTROL VIEW)
Clicking the [CAMERA CONTROL VIEW] button opens
the window.
Camera Selectbutton displays the live image of the
selected camera number.
Main Control Panel Tabreturns the window to the
main control panel.
ZOOM (WIDE/TELE)buttons zoom the image in or out.
FOCUS (FAR/NEAR/AUTO)buttons adjust the focus of
the image. When AUTO is clicked, the camera will
adjust the focus by itself.
IRIS (CLOSE/OPEN/RESET)buttons adjust the iris of
the image. When RESET is clicked, the iris will return to
the factory default setting.
AUTO PAN (ON/OFF)buttons allow the camera to pan
endlessly within the preset range. 
PRESETallows the camera to turn to the preset posi-
tion specified by the number.
PAN/TILT Control:
Clicking the desired direction in the image display area
will move the camera if it is mounted on a pan/tilt table.
The image display area is assigned panning/tilting
function with the mouse click. The 25-split (5x5) areas
are invisible, but each represents a moving direction:
up, down, right or left.
UP
DOWN LEFT
RIGHT 
						

							75
Clicking the alarm list tab on the main control panel opens
the list.
Alarm events are listed with event numbers, dates, channel
numbers, and event types.
PREVbutton returns the list page to previous one.
NEXTbutton opens the next page.
Alarm List Searchbutton opens the search dialog.
Event types are abbreviated as follows in the list.
TERM: The alarm terminal on the rear of the WJ-HD200
is activated.
VMD: The built-in Video Motion Detector operates.
PC:The recorder received an alarm from a PC.
Alarm List
Specify the month, day, year, and time of the event you
wish to search.
Click the [OK] button. The dialog disappears, and the
searched event will be highlighted in the alarm list.
Note:Searching may take 18 seconds at worst particularly
when the recorder runs simultaneous recording and
playback, and/or when the targeted image is of small
size. 
						

							Slow image refreshment and/or slow
response to operations Remote operations are not accepted
while BUSY indicator is lit.
When accessing via the network:
76
Phenomenon
Power is not turned on.
Error message NO DISK is displayed
on the monitor.Connect the power cord to AC outlet.
TROUBLESHOOTING
Power cord not properly connected
No disk available
Disconnection of camera, camera
cable, or VIDEO IN BNC.
Ventilation blocked, or failure of cooling
fan
HDD status may have changed, or a
malfunction may have occurred.
Lens cap not removed from the cam-
era, some device is not turned on, or
brightness and contrast of the monitor
are improperly adjusted.Refer to HDD MAINTENANCE in
Appendix to confirm the HDD status.
Consult your dealer when a malfunction
is found.
Connect the respective camera, cable,
or connector properly.
Remove obstacles, or consult your
dealer for servicing.
Reset the recorder to the factory
defaults (page 24) and enter a new
password.
Check the HDD status referring to HDD
MAINTENANCE. Consult your dealer
when a malfunction is confirmed.
Detach the lens cap, turn on the
device, or adjust the monitor. Error message CH n LOSS (n=1-8) is
displayed on the monitor.
Error message TEMP ERROR is dis-
played on the monitor.
Administrator password cannot be
recalled.
DISK MENU appears when turning on
the power.
Camera picture is not displayed on the
monitor.
Cause What to do
Nine-split display does not function. Set it to ALL.QUAD ONLY may be set for MULTI
SELECT MODE.
Setup menus supplied from the Matrix
Switcher are not recorded.The WJ-HD200 does not record non-
interlace video.
Wait until the preceding accesses end.
Wait until the preceding accesses end. Front panel buttons on the recorder are
being operated, or more than four PCs
access the recorder.
Network is busy.
Intermittent sound reproduction  Network is busy.
No click sound desired. Change the setting as follows: Control
Panel 
→Sound Multimedia →Sound
Tab 
→Explorer →OFF Default setting is ON. 
						

							77
SPECIFICATIONS &
APPENDIX 
						

							78
SPECIFICATIONS
General
Power Source Required: 120 V AC, 60 Hz
Power Consumption: 45 W
Ambient Operating Temperature: +5 °C - +45 °C (41 °F - 113 °F)
Ambient Operating Humidity: Less than 85 %
Dimensions: 420 mm (W) x 44 mm (H) x 350 mm (D)
16-9/16 (W) x 3-7/16 (H) x 13-3/4 (D)
Weight: 5.2 k
g(11.4 lbs.)
Input
Video Input: 1.0 V[p-p]/75 ΩComposite video signal with 75 ΩAutomatic Termination / Looping
through (x8)
Audio Input:–10 dB 10 kΩunbalanced, RCA standard jack
Image Process
Compression System: JPEG
Pixel Rate: 672 x 224
Refresh Rate: 30 FPS maximum
Output
Video Output: 1.0 V[p-p]/75 ΩComposite video signal/Looping through (x8)
Video Output Front Panel: 1.0 V[p-p]/75 ΩComposite video signal (x1)
Audio Output:–10 dB 600 Ωunbalanced, RCA standard jack (x1)
Audio Output Front Panel:–10 dB 600 Ωunbalanced, RCA standard jack (x1)
Spot Monitor Output: 1.0 V[p-p]/75 ΩComposite video signal (x1)
Multiscreen Monitor Output: 1.0 V[p-p]/75 ΩComposite video signal (x1)
Control Port
Alarm/Remote Port: 25-pin Full Pitch D-sub connector (x1)
Alarm Input 1-8, Alarm Reset Input, EXT REC Input, Time Adjust Input, Sequence
Input: Low-active, Non-voltage N.O. Contact, ≥100 ms
Alarm Recovery Output 1, Disk End Status Output, Time Adjust Output,
Warning Output, REC Status Output, Sequence Output: Low-active, Open-collector,
24 VDC 100 mA max.
Alarm Output 1, Play Status Output: Low-active, Open-collector, 
12 VDC 100 mA max.
Alarm Output 2: High-active, 12 V 4.7 kΩ
Alarm Recovery Output 2: High-active, 12 VDC 220 Ω
RS-485 (PS
•Data): 6-conductor modular jack (RJ-11)
RS-232C: 9-pin Full Pitch D-sub connector
10/100BASE-TX Port: 10Base-T and 100Base-TX, 8-conductor modular jack (RJ-45)
Protocol Installed: TCP/IP, HTTP, FTP, SMTP, SNMP, DNS, DDNS
Security: Password-protected
Hard Disk Drive
Built-in: 120 GB (x1)
Extension: Optional 1 unit, available using built-in bracket
Weight and dimensions shown are approximate.
Specifications are subject to change without notice. 
						

							79
STANDARD ACCESSORIES
Rack Mounting Bracket  ............................................................... 2 pcs.
Screw for Rack Mounting Bracket (M3x10) ................................. 6 pcs.
Absorber ...................................................................................... 4 pcs.
Sleeve .......................................................................................... 4 pcs.
Hard Disk Fixing Screw  ............................................................... 4 pcs. 
						

							80
Item
SHIFT
SETUP
FUNCTION
Step playback REW Alarm record
playback/stop Setup menu display on/off
The top of the oldest record will be
accessed. Jump to oldest
UP
LR
UP
DOWNR
WV-CU360
APPENDIX
Remote Control from System Controller
A system controller having PS•Data capability can control the WJ-HD200. The table compares operations of the WJ-HD200
and of the system controller WV-CU360. Make certain that the protocol selection for the WJ-HD200 is set to PS
•Data.
Setup item selection
Parameter selection
Cursor return to setup or
last screen restored
Alarm list display on/off
Alarm event searchWJ-HD200 Note
Button lock is released automatical-
ly by opening the setup menu.
Hold down
2 seconds
STOPSETUP
/ESC
PUSH–   PAUSESET//
PUSH–   PAUSESET//
PUSH—   PAUSESET//Press
CAM
SET
STOPSETUP
/ESC
STOPSETUP
/ESCPLAYCAMMON
ESC SET
SETUP
FUNCTION
Hold down
2 seconds
DOWN LR
UP
LR
DOWN LR
UP
DOWN LR
MON
ESCALM RESET
ALM RECALLSHIFT
RecordingRECSETUP
FUNCTIONSHIFT
Playback and recording
stop
Playback stop
Recording stopSTOPSETUP
/ESC
STOPSETUP
/ESC
REC STOP
SETUP
FUNCTIONSHIFT
PlaybackPLAYSETUP
FUNCTIONSHIFT
PausePUSH–   PAUSESET//SETUP
FUNCTIONSHIFT
Step playback FWDPUSH–   PAUSESET//STEP/
PUSH–   PAUSESET//STEP/
SETUP
FUNCTIONSHIFTSETUP
FUNCTIONSHIFT
Skip playback FWDPUSH–   PAUSESET//REW/FF/SHIFT
SETUP
FUNCTION
Skip playback REWPUSH–   PAUSESET//REW/FF/
Jump to latest
The top of the latest record will be
accessed.PUSH–   PAUSESET//REW/FF/Press 
JogDial
SETUP
FUNCTIONSHIFTPUSH–   PAUSESET//REW/FF/Press 
JogDial
SETUP
FUNCTIONSHIFT
SETUP
FUNCTIONSHIFT
SHIFT
SETUP
FUNCTION
Exclusive use to stop playback
Exclusive use to stop recording
Hold down
2 secondsHold down
2 seconds
Press
JogDial
Press
JogDial
Lower layer menu
PUSH–   PAUSESET//
      1/2         1PLAY        2PLAY  
3FF          2FF           1FF
1/2         1PLAY        2PLAY
  3REW       2REW        1REW