Panasonic Digital Disk Recorders Wj Hd309 Operating Instructions

							161
Check item/RemedyProblemPage
The additional disk space of
HDD is not displayed.
The available disk space of
HDD is not displayed on the
right bar.
Cannot establish a connection
via the network.
Response or Image update
takes time.
The power cord insulation is
damaged.
The power cord, plug and con-
nectors get hot during use.
The power cord gets hot when
bent or stretched.
Inspect the power cord, power plug and connectors periodically.•Check if Disk End Mode is set to STOP.
•Check if the Disk End Mode is set to STOP.
•Check the network settings of the unit and PC.
•Check if the network is crowded.
•The power cord, plug and connectors are worn out. This may result in electric
shock or a fire. Unplug the power plug from the AC outlet immediately, and
refer to qualified service personnel.
•Check the host registration setting. When host authentica-
tion is set to ON, you cannot establish the connection
from computers other than the PC registered as the host.
•Check if there is a partition in the HDD.
•Check if there is a partition in the HDD.
Refer to p. 95.
Refer to p. 95.
Refer to the Net-
work Setup In-
structions (PDF).
– Refer to p. 119
and 124. –
–
Rebooting of the unit occurs
while displaying the splash
startup screen.
–
When the unit fails to find all of the connected extension units
(WJ-HDE300 series) previously mounted for the following rea-
sons, it may take time to start up because the unit will be
restarted while displaying the splash startup screen. They are
normal operations.
• When dedicated cables connecting the unit and the extension
units are not firmly connected or detached
• When all of the extension units previously mounted are
disconnected 
						

							162
General
SPECIFICATION
Power source:
Power consumption
Ambient operating
temperature
Ambient operating
humidity
Dimensions
Weight
Input/Output
Video
Audio
Others
*
1When power is not supplied, the video output signal was not sent from the unit even if a video input signal is supplied.
*2Non-voltage N.O. Contact, 100 mA, +5 V pull-up
*3Open collector output, maximum under conditions of 24 V DC and 100 mA or less
*4High (+12 V, 6.3 mA)
*530 KΩ, 5 V pull-up, –100 mA, N.O. Contact
*65 V pull-up, –100 mA, Non-voltage N.O. Contact input
*7200 mA at maximum
*8Changeable with the mode switchVideo input connectors
Cascade input connector
Video output connectors
Monitor output connectors
Monitor output connector
(VGA)
S-video output connector
Video output connector
(front panel)
Audio input connectors
Expansion connector Audio output connectors
Copy connectors
Control connectors
Alarm port
RS-485 ports
DATA ports
SERIAL connector
Ethernet port220 V - 240 V AC, 50 Hz
85 W
+5°C to +45°C (41 °F - 113 °F)
Less than 85 %
420 mm (W) X 88 mm (H) X 350 mm (D) [16-9/16 (W) X 3-7/16 (H) X 
13-3/4 (D)] (excluding rubber feet and projections)
9.5 kg(21 lbs.)
1 V [P-P] / 75 Ω, with auto termination loop-thru, vertical timing pulse mul-
tiplexed, x8 (1 to 8 CH) (BNC)
1 V [P-P] / 75 Ω, with auto-termination loop-thru, 
x8 (9 to 16 CH) (BNC)
1 V [P-P] / 75 Ω(BNC)
1 V [P-P] / 75 Ω, active loop-thru output, x8 (1 to 8 CH) (BNC)*
1
1 V [P-P] / 75 Ω, active loop-thru output, x8 (9 to 16 CH) (BNC)
1 V [P-P] / 75 Ω, x2 (BNC)
RGB output, x1 (15-pin D-sub)
Y = 1 V [P-P] / 75 Ω, C=0.286 V [P-P] / 75 Ω, x1 (S-video output connec-
tor)
1 V [P-P] / 75 Ω, x1 (RCA pin)
–10 dB, 10 KΩ, x4 (RCA pin)
High-speed serial interface, 480 Mbps (theoretical value), x1
High-speed serial interface, 480 Mbps (theoretical value), x2
Emergency recording input*
2, additional space warning output*3(for
devices connected to copy connectors), HDD trouble output*3, camera
trouble output*3, trouble output*3, electricity failure recovery completion
output*4, time adjust input/output*5, sequence switching input/output*5,
electricity failure detection input*2, external recording mode switching*2
(25-pin D-sub) , +5 V output *7
1 to 8 CH alarm input*6, 1 to 16 CH alarm input*2, 1 to 16 alarm output*3,
alarm recovery input*2, alarm suspension input*5(25-pin D-sub)
RS-485 (full duplex/half duplex*
8), x2 (RJ-11)
RS-485, x2 (RJ-11)
RS-232C, x1 (9-pin D-sub)
10 Base-T/100 Base-Tx (RJ-45) –10 dB, 600 Ω, unbalanced, x2 (RCA pin) 
						

							163
STANDARD ACCESSORIES
CD-ROM* ............................................................................ 1
Operating Instructions (this manual)  .................................. 1
The following are for installation:
Power Cord  ......................................................................... 2
Rack Mounting Bracket  ...................................................... 2
Screw for Rack Mounting Bracket  ...................................... 4
Cable Clamp ....................................................................... 1
Screw for Cable Clamp  ...................................................... 1
Hard Disk Drive Fixing Screw  ............................................. 4
*The following are included on the CD-ROM:
Viewer software
Plug-in software
Network Operating Instructions (PDF)
Network Setup Operations (PDF) 
						

							Matsushita Electric Industrial Co., Ltd.
Osaka, Japan
http://www.panasonic.co.jp/global/
2004     © Matsushita Electric Industrial Co., Ltd.  All rights reserved.NM0104-2034      3TR001707CAA       Printed in Japan