Panasonic Digital Disk Recorders Wj Hd500a Operating Instructions

11
&6Electronic Zoom Button (EL-ZOOM)
Use this button to enter or exit the electronic zoom
mode.
In the EL-ZOOM mode an image presently displayed in
single spot can be enlarged and compressed on the
Multiscreen Monitor.
&7Group Selection Button (GROUP SELECT)
Selects the camera group from among group 1, 2, 3
and 4.
The LED will light while any of the groups is selected.
&8Index Button (INDEX)
Displays the all record list (list and thumbnail) or alarm
and emergency list depending on the status of the...

4. Insert the absorbers on to the chassis as shown in the
figure.
5. Place the hard disk on the chassis, then fix it with the
four screws and sleeves with the earth lug as shown in
the figure.
6. Set the unit address with the jumper connector on the
hard disk drive, as shown in the figure, for example.
7. Install the hard disk with the chassis into the Disk
Recorder by sliding it from the front.
8. Plug in the power cable and interface flat cable pre-
pared in the power inlet and interface connector of...

13
5. Place the Motion Detector Board on the Analog Board,
as shown below, and plug in the boards.
6. Fix both boards with the 3 supplied screws, as shown
below.
7. After installing the board, connect CN403 and the main
board, then secure them by tightening the screws
shown below.Installing the Optional Motion
Detector Board
The Motion Detector Board WJ-HDB501 is installed exclu-
sively in the WJ-HD500A Disk Recorder.
1. Unplug the power cord from the WJ-HD500A Digital
Disk Recorder, or disconnect the...

14
Installing the Optional Network Board
The Network Board WJ-HDB502 is installed exclusively in
the WJ-HD500A Disk Recorder.
1. Unplug the power cord from the WJ-HD500A Digital
Disk Recorder, or disconnect the plug from the AC out-
let.
2. Remove the top cover of the Disk Recorder by remov-
ing the 11 screws, as shown in the figure.
3. Remove the small plate covering the 10/100BASE-T
port hole on the rear of the Disk Recorder by removing
the screw shown in the figure.
4. Remove the 6 screws on the...

15
Mounting into the Rack
The Disk Recorder can be mounted into the rack as
described below.
1. Remove the four rubber feet by removing the four
screws from the bottom of the Disk Recorder.
2. Place the rack mounting brackets on both sides of the
Disk Recorder and tighten with the four supplied
screws (M4 X10).
3. Install the Disk Recorder with the rack mounting brack-
ets in the rack, securing it with four screws (not includ-
ed).
Cautions:
• The cooling fan inside the Disk Recorder is subject to
wear...

16
CONNECTIONS
Shown below are examples of system connections.

ON
OFFPOWER
ON
OFFPOWER
REMOTO
TIMER
OPERATE
FULL
HDD
SEQUENCESET LOCK
ALARM
ALARM
RESET
ALARM
SUSPENDMULTISCREEN
SELECT
SET UP
/ESCGROUP
SELECT
SPOTMULTISCREEN
DAYLIGHT SAVINGS
EL-ZOOM
COPYREC PREVIEWINDEXSTOP PLAY/    PAUSE REC
FWD REV
ALARM SEARCH
DISPLAYREC STOP1234
1314151691011125678
Digital Disk
Recorder
WJ-HD             A 
FS16 16Spot Monitor
Multiscreen Monitor Digital Disk Recorder WJ-HD500A
Remote Controller
WV-CU50
16 Cameras...

17
Connection with the Remote
Controller
Connect the Remote Controller to the REMOTE port on the
rear of the Disk Recorder with the supplied modular cable.
Connection with the Camera Sites
Connect cameras (or camera site equipment) to the VIDEO
IN connectors (1 to 16) on the rear of the Disk Recorder
with the coaxial cable.
Connection with the Monitors
Connect the monitors to the SPOT OUT connector and
MULTISCREEN OUT connector on the rear of the Disk
Recorder with the coaxial cable.
16
1615
1514
14...

18
Alarm Port Connection
The ALARM port can be used for connecting the alarm sen-
sor and alarm control switches. It is also used to synchro-
nize the sequence as shown below.
• Connect the sensor switches to the ALARM port on the
rear of the Disk Recorder, as shown in the example
below.
Designation Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13Alarm Input 1
Alarm Input 2
Alarm Input 3
Alarm Input 4
Sequence Timing Input
Alarm Reset Output
Ground
Alarm Recover Input
Alarm Output
Alarm Input 10
Alarm Input 11...

19
• Time adjustment can be enabled connecting with the
external device as shown below.
• The Extension Units are installed in the system for
extending its disk capacity.
Connect each thermal error output from the Extension
Units with the CONTROL Port on the rear of the WJ-
HD500A Disk Recorder as shown below.
The WJ-HD500A will display the warning for thermal
error on the monitor.Control Port Connection
The CONTROL port can be used for controlling the system
with the outboard device as shown below....

20
(Remaining HDD Capacity Alarm Output)
CONTROL Input/Output(15)
Alarm Device
Relay, etc. (6)Ground
Power Failure Process
Completion OutputUPS Shut Down
Line Fail signal
(Normally Open)
CBefore connecting the UPS,
   refer to the manual of
   your UPS. Power Failure Detect Input
Ground Common
Power Cable Disk Recorder
WJ-HD500A
CONTROL(19) (17) (16)
Uninterrupted
Power Supply
to AC outlet
Connection with the Uninterrupted Power Supply (UPS)
• The figure shows an example of how to connect a UPS as...